Summary of Contents for Test-Um Lil' Buttie Ranger
- Page 1 LB250 Lil’Buttie ® TELEPHONE TEST SET with Amplified Speaker 805-383-1500 805-383-1595 www.test-um.com • • 808 Calle Plano Camarillo, CA 93012 •...
-
Page 2: Table Of Contents
6. Troubleshooting .................42 4.1.3 The MON Setting (MONITOR Mode)....20 6.1 Warranty ................42 4.2 Using the LCD Panel ............21 6.2 Calling Test-Um ..............43 4.3 Using the Mute Button .............22 6.3 Warranty Service ..............44 4.4 Using the Speaker Button..........23 6.4 Non-Warranty Service............44 4.5 Using the Function Button ..........24... -
Page 3: Specifications
Lil’ Buttie RANGER CHAPTER 1: Specifications Measurement — Voltage: 0 to 128 VDC ± 5%; 1. Specifications Current: 10 to 140 mA ±5%; Note: Do not attach test set to electric-power lines Interfaces — Telephone system: Modular telco; User Controls — One left-side-mounted TALK/BELL/MON slide Headset: 2.5 mm cell-phone type switch for operating mode;... -
Page 4: Introduction
It also comes with a cordura carrying case that holds the test set, head set and cord set. Optimum results with the Ranger are obtained with Test-Um supplied cord sets. See Section 7.1 for more available styles of cord sets. -
Page 5: Features And Benefits
Lil’ Buttie RANGER CHAPTER 2: Introduction hook line. The test set has high impedance with 2.2 Features and Benefits small series capacitance, so there won’t be any • Compact size with normal earpiece-to-microphones popping or clicking on the line when you attach spacing;... - Page 6 Lil’ Buttie RANGER CHAPTER 2: Introduction • Performs last-number redial and can also store – High voltage lockout for Pair Gain lines (high voltage digital lines) and recall as many as eight other preprogrammed numbers. Each of these phone numbers can –...
-
Page 7: The Ranger Illustrated
Lil’ Buttie RANGER CHAPTER 3: Installation and Battery Replacement 3. Installation and Battery Replacement 2.3 The Ranger Illustrated Figure 2-1 below shows the Ranger and indicates what 3.1 Connecting the Ranger to a Phone Line its various controls and other components are for. The Ranger is designed with a standard RJ-12 (6 wire Lanyard (hook) for hanging test set by RJ-11) modular jack for quick connection to a phone... -
Page 8: Connecting The Headset To The Ranger
Lil’ Buttie RANGER CHAPTER 3: Installation and Battery Replacement Figure 3-1. Connecting the cable set. 3.3 Replacing the Battery The Ranger comes with a battery installed, so you can use it right out of the box. But when the “low battery” icon comes on in the Ranger’s LCD panel, you’ll need to replace the current battery with another 9-volt alkaline battery. -
Page 9: Operation
Lil’ Buttie RANGER CHAPTER 4: Operation 4. Operation CAUTION! Do not over-tighten this screw — damage to the test set might result. If you have problems closing the battery door, 4.1 Using the TALK/BELL/MON Switch confirm that the battery is properly seated, the battery cable is properly routed and that the door is fully interlocked with The TALK/BELL/MON switch is on the left side of the the rest of the Ranger’s case. -
Page 10: The Bell Setting (Bell Mode)
Lil’ Buttie RANGER CHAPTER 4: Operation “Flash to connect” prompt on line 2. If you still want ™ When the Traffixguard High feature is selected as OFF to go offhook despite this voltage reading, press the in the setup menu: Ranger’s Flash key and the Ranger will go off hook and The Ranger does not check for line voltage exceeding attempt to operate normally. -
Page 11: The Mon Setting (Monitor Mode)
Lil’ Buttie RANGER CHAPTER 4: Operation or FAIL depending on the correctness of the received 4.2 Using the LCD Panel data. If you leave the TALK/BELL/MON switch in this The Ranger has a reflective type, super twisted liquid position when the Ranger is ringing, nothing will happen crystal display (LCD). -
Page 12: Using The Mute Button
Lil’ Buttie RANGER CHAPTER 4: Operation 4.3 Using the Mute Button 4.4 Using the Speaker Button When the test set is off hook in the TALK mode and the When the test set is in the TALK mode or MONITOR loudspeaker OFF, you can mute the output from the mode, the speaker button is used to turn the loudspeaker Ranger’s microphone by pressing down the mute button... -
Page 13: Using The Function Button
Lil’ Buttie RANGER CHAPTER 4: Operation 4.5 Using the Function Button 4.6 Using the Command Keys The Function (FCN) button acts to modify the operation There are sixteen pushbutton keys on the keypad of the of some of the keys on the keypad. The function button Ranger. - Page 14 Support (it dials the phone number for Technical 3.8 seconds to the usual interdigit delay between Support at the Test-Um factory.) dialed digits. (You might want to do this, for • If you press Recall and then press Tone or Pause,...
-
Page 15: Command-Key Functions In Scrolling-Recall And Setup Modes
TALK mode from or press Menu (Rcl) to escape back to normal operation. the first menu screen, Note: slot 9 is permanently pre-programmed to store the number of Technical Support at the Test-Um factory (805-383-1500.) -
Page 16: Setup Mode
Lil’ Buttie RANGER CHAPTER 4: Operation any current number will be cleared and the 4.8 Setup Mode number string you type in will become that slot’s To get into setup mode from TALK mode (normal new stored phone number. (Pause corresponds operation) or MONITOR mode, press FCN RCL (Menu) to a 3.8-second pause embedded in the number, or Recall twice. - Page 17 Lil’ Buttie RANGER CHAPTER 4: Operation combination to just advance the cursor (pressing • Call Waiting ID – Use this screen to turn the FCN [↓→] again will enter a space into the name Ranger’s Call Waiting Caller ID (CWCID) feature ON or OFF.
-
Page 18: Special Features
Lil’ Buttie RANGER CHAPTER 4: Operation • Guard High Volt – This screen allows the high volt- If you still want to connect, press the Flash key to connect. age lockout feature to be turned ON and OFF. The voltage is constantly updated, so while the Ranger (The factory default is ON.) Use the ↓→... -
Page 19: Automatic Power-Off
Lil’ Buttie RANGER CHAPTER 4: Operation voltage is displayed along with the messages “V TOO the screen in minutes. The TALK mode times out in HIGH!” “DISCONNECT NOW!!” The test set will display approximately 60 minutes with CWCID (Call Waiting this message and sound the alarm until the line voltage Caller ID) OFF and 30 minutes with CWCID ON. -
Page 20: On-Hook Caller Id
Lil’ Buttie RANGER CHAPTER 4: Operation end of the message, but the Ranger calculated 4.9.6 On-Hook Caller ID the checksum yy from the received data. While it’s in BELL or MONITOR mode, the Ranger • “Lost Carrier” – The Ranger detected the detects and displays on-hook Caller ID information. -
Page 21: Loudspeaker
Lil’ Buttie RANGER CHAPTER 5: Maintenance 5. Maintenance The test set decodes all 16 possible DTMF tones. The DTMF display remains on the screen for about two minutes unless the TALK/BELL/MON switch is changed You can clean the Ranger with a damp cloth. If the test or the FCN CL key combination is pressed to CLEAR set is very dirty, you may apply a small amount of liquid the display. -
Page 22: Troubleshooting
• the results of any testing (of the Ranger itself) other than Test-Um Inc. authorized personnel. In no that you’ve already done. event will Test-Um Inc. be liable for any incidental or consequential damages. -
Page 23: Warranty Service
All units returned for warranty repair will be repaired • Attach a description of the operational problem. or replaced free of charge, at the discretion of Test-Um Inc., and will be shipped freight prepaid. In the event • Include a contact name, phone number, and e-mail address (if possible). -
Page 24: Accessories
Approximately 5 feet in length Accessories can be obtained by contacting your local with modular plug and strain relief grommet distributor, or directly from Test-Um by contacting us on one end and self-piercing bent nose clips at 805-383-1500. Also see out website at www.test-um.com on the other end. -
Page 25: Modtest Adapters
Lil’ Buttie RANGER CHAPTER 7: Accessories 7.3 Modtest Adapters 7.4 Test Set Carrying Accessories • 4-Position Modtest Adapter, Part Number LB64 • Deluxe Swivel Belt Clip, Part Number LB60B Pass-through cable adapter with 6-position RJ-12 Plastic belt clip which can be attached with a jack on each end. - Page 26 NOTES NOTES...