Advertisement
General Installation Manual
INSTALLATION
General
•
Please read this guide completely
before installation or use of the
modules.
This
section
electrical
and
specifications needed before using
your SANYO PV modules.
•
Modules should be firmly fixed in
place
in
a
manner
withstand
all
expected
including wind and snow loads.
•
The drilling and addition of ground
holes is permitted, but should be
avoided whenever possible to avoid
damage to the module.
additional
ground
necessary, they must not penetrate
the inner side of the aluminum frame.
Caution
is
advised
accidentally drilling, scratching, or
penetrating the back sheet surface of
the module.
If required, it is
recommended
to
add
ground holes to the outer aluminum
lip area of the module. In such case,
additional ground holes must be at
least 65 ㎜ away from any frame
corner.
•
For a non-integral module or panel, a
statement that the assembly is to be
mounted over a fire resistant roof
covering rated for the application.
•
Appropriate material should be used
for mounting hardware to prevent the
module frame, mounting structure,
and hardware itself from corrosion.
•
Install modules where they are not
shaded by obstacles like buildings
and trees. Especially pay attention to
avoid partially shading the modules
by objects during the daytime.
•
Please
contact
your
Authorized
Representative
questions regarding mounting profiles
for modules if needed.
Notes on Installation
•
Clearance between the roof surface
and module frame is required to allow
cooling air to circulate around the
back of the module. This also allows
any condensation or moisture to
dissipate. Install modules so that air
can circulate between the roof and
the module.
•
We recommend installation methods
shown in Figure 1. In some areas,
local electrical codes may govern the
installation and use of PV modules.
Operating Conditions
SANYO recommends that modules be
operated within the following Operating
Conditions. An installation location with
conditions
beyond
the
Conditions
or
with
other
Conditions (see below) should be avoided.
Operating Conditions of SANYO modules
are as follows:
1)
The modules should be operated only
in terrestrial applications. No space or
other Special Conditions (see below).
contains
2)
The ambient temperature should be
mechanical
within –20° C (-4° F) to 40° C (104° F).
3)
The relative humidity should be within
45% to 95%.
4)
The installation place should be less
suitable
to
than 1,000m (3,280ft) above sea
loads,
level. Installations more than 1,000m
(3,280ft) are allowed only if the wind
pressure load for a module is less
than 2,400N/m
When
Special Conditions
holes
are
1)
The
ambient
installation place are different from
the
to
avoid
Conditions.
2)
Salt
damage
installation place.
3)
Hail and snow damage is excessive
additional
at the installation place.
4)
Sand and dust damage is excessive
at the installation place.
5)
Air
pollution,
vapors, acid rain, and/or soot, etc. are
excessive at the installation place.
Installation (reference) – HIP - xxxNHE5, - xxxNHE5 - BO2
·
For questions regarding mounting profiles for modules, please co ntact your local dealer.
For questions regarding mounting profiles for modules, please co ntact your local dealer.
SANYO
with
Mounting
Mounting
Structure Rail
Structure Rail
Spring washer
Spring washer
Flat washer
Flat washer
Flat washer
Spring washer
Spring washer
Operating
Special
2
(50PSF).
temperature
and
recommended
Operating
is
severe
at
the
chemically
active
Installation (reference)
M6 Nut
M6 Nut
Flat washer
Section A-A
M6 Bolt
M6 Bolt
Section A - A
Figure1 : Installation
2
SPECIFICATIONS
Notes on Specifications
1)
Rated electrical characteristics are
within 10% of the values measured at
Standard
Test
Conditions
Irradiance of 1000W/m
temperature,
and
irradiance per IEC 60904-3.
2)
Under
normal
conditions,
photovoltaic module may experience
conditions that produce more current
and/or
voltage
than
standard component test conditions.
Accordingly, the values of Isc and
Voc should be multiplied by a factor
of 1.25 when
determining voltage
ratings, conductor capacities, fuse
sizes, and size of controls connected
to the module output.
3)
The current output for the modules
shown
in
the
Specifications
measured
at
Standard
Conditions.
These conditions may
not be frequently observed in actual
practice.
Application class of product
SANYO HIT PV-modules are applied to
application class A. Application class A for
HIP - xxx NE3, - xxxNE3 - BO - 2
Solar Module
Solar Module
A
A
A
A
Solar Module
Solar Module
Module
Module
Mounting Structure Rail
Mounting Structure Rail
(STC).
2
o
, 25
C cell
solar
spectral
a
reported
at
is
Test
Advertisement
