Related Manuals for Gearmore FM-60
Summary of Contents for Gearmore FM-60
- Page 1 FINISHING MOWER Operation, Service & Parts Manual For FM-60, FM-72, SFM-72, & SFM-84 February 2000 FORM: FinishingMowerBook.QXD...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction ......1 Safe Operating Rules ..... .2 Operational Safety . -
Page 3: Introduction
INTRODUCTION We welcome you as an owner of a Gearmore mower. Please read the following instructions and refer to them when required. This manual contains valuable information about your new Gearmore Mower. It has been carefully prepared to give you helpful suggestions for operating, adjusting, servicing and ordering repair parts. -
Page 4: Safe Operating Rules
SAFE OPERATING RULES The area to be mowed should be a clean area, free of debris. Do not operate on steep hillsides. Do not allow passengers on tractor or mower. Keep all safety shields in place at all times. Always shut mower and tractor completely off before performing any maintenance on mower. -
Page 5: Operational Safety
OPERATIONAL SAFETY FAILURE TO OBSERVE THE FOLLOWING MAY RESULT IN SERIOUS INJURY OR DEATH. ONLY A PROPERLY TRAINED OPERATOR SHOULD OPERATE THIS MOWER. KEEP ALL OTHERS OFF TRACTOR AND MOWER. NEVER ALLOW CHILDREN TO OPERATE TRACTOR AND MOWER. BEFORE OPERATING MOWER: Read operator’s manual carefully for safe operation of this mower. - Page 6 OPERATIONAL SAFETY DANGER DANGER Keep away - Rotating Blades To prevent serious injury or death To prevent serious njury ordeath * Never operate mower if shields when blades are rotating due to and guards are not in good engine running. condition or have been removed.
-
Page 7: Set-Up Instructions
SET-UP INSTRUCTIONS Your Gearmore Finishing Mower has been carefully assembled at the factory. By following a few simple instructions, your Finishing Mower will be ready for dependable service. This Finishing Mower is designed to fit most tractors equipped with a standard three (3) point system. -
Page 8: Belt Replacement
BELT REPLACEMENT TO REPLACE BELT: STEP 1 Remove PTO shaft. STEP 2 Remove top cover. STEP 3 Loosen nut on adjustment pulley to allow for movement. (See Figure D) STEP 4 Loosen nut on right side of “L” bracket. (See Figure D) STEP 5 Loosen belt by moving adjustment pulley in opposite direction you would to tighten belt. - Page 9 BELT REPLACEMENT Page 7...
-
Page 10: Parts Diagram
PARTS DIAGRAM Page 8... -
Page 11: Parts List
PARTS LIST REF# PART NO. DESCRIPTION 403684 124685 124686 403687 Top Cover 403024 403025 403025 403025 Gearbox Plate 312647 312647 312647 Idler Pulley Bracket 312641 312641 Double Idler Pulley Bracket 502300 502300 502300 Spindle Unit - Single 502301 502301 Spindle Unit - Double 164090 164090 164090... -
Page 12: Gearbox Assembly
GEARBOX ASSEMBLY Page 10... - Page 13 GEARBOX ASSEMBLY REF# PART NO. DESCRIPTION 155005 Bearing 185007 Input Gear - 184000 Gearbox 185010 Input Gear - 184005 Gearbox 131031 Snap Ring 186010 Input Shaft 155010 Bearing 129010 Housing 131035 " Pipe Plug 131040 " Pipe Plug 185005 Output Shaft - 184000 Gearbox 185006 Output Shaft - 184005 Gearbox 131045...
-
Page 14: Blade Spindle Assembly
BLADE SPINDLE ASSEMBLY REF# PART NO. DESCRIPTION 155009 Ball Bearing 156026 Seal 502311 Spindle Pulley w/Nut & Key (502300 Spindle) 502312 Spindle Pulley w/Nut & Key (502301 Spindle) 502310 Blade Bolt Set (3) w/Washer 191302 Spindle Cap Page 12... -
Page 15: Driveline
PTO DRIVELINE 147022 REF# PART NO. DESCRIPTION 170120 Roll Pin 151045 Male Tube End Yoke 151040 Implement End Yoke 151050 Female Tube End Yoke 151035 Tractor End Yoke 151091 Inner Tube 14 Series 151090 Outer Tube 14 Series 170015 Cross Kit #4 170110 Quick Disconnect Pin 124310... -
Page 16: Limited Warranty
Our obligation shall be limited to repairing or replacement of any part, provided that such part is returned within thirty (30) days from date of failure to Gearmore through the dealer from whom the purchase was made, transportation charges prepaid.