Advertisement
Beforeyoustart...
Remove all contents from the upper
cabinet.
Important: Observe all governing
codes and ordinances.
Check location where microwave oven
will be installed. The wall must be
strong enough to support the microwave
oven weight of 150 lbs., plus the weight
of any items placed inside the
microwave or the upper cabinet. The
location should be away from strong
draft areas, such as windows, doors,
and strong heating vents. The
microwave oven should be located for
convenient use in the kitchen.
Proper installation is the installer's
responsibility. A qualified technician
should install this microwave oven.
Make sure you have everything
necessary for correct installation.
It is the responsibility of the installer to
comply with the installation clearances
specified on the serial/rating plate.
The serial/rating plate is located
Excessive Microwave Energy
Exposure
. Do Not attempt to operate this
microwave oven with the door
open.
. Do Not tamper with or defeat
the safety interlocks.
. Do Not place objects between
the microwave oven front face
and the door.
. Do Not allow soil or cleaner
residue to accumulate on
sealing surface of microwave
oven door.
. Do Not operate microwave
oven if it is damaged.
. The microwave oven door
must close properly to provide
safe operation. Do Not use
microwave oven if door is bent;
hinges and latches are broken
or loose; or door seals, sealing
surfaces or glass are broken.
n
The microwave oven should
only be adjusted and repaired
by a qualified repair person.
. Have a qualified repair person
check for microwave leakage
if a repair is made.
Failure to use microwave oven
except as instructed may result
in exposure to excessive
microwave energy.
behind the micr&vave oven door on
the front frame of the microwave oven.
Electrical ground is required. See
Electrical requirements.
II I
For comer installations,
allow
enough clearance to fully open
door so that rack and cooking
utensils can be removed
Y
I-
30" min cabinet
opening width
c
I
Y
t
15" minimum'microwave
oven to cooking surface
or countertop
30" min~clearance from
. . .
Wall construction should
be a minimum of 2" x 4"
wood studding and 3/8"
thickness drywall or
Use templates included
with installation
instructions.
Remove all packaging material from
inside microwave oven. Check the
microwave oven for damage - see
WARNING for excessive microwave
energy exposure. If any damage is
evident, do Not operate the microwave
oven until it is checked by an authorized
Whirlpool service technician
Personal Injury Hazard
Two people are required to lift
this microwave oven.
Failure to use more than one
person during installation may
result in personal injury.
. This microwave oven must be
mounted against and supported
by a flat, vertical wall.
. This microwave oven must be
attached with two lag screws
to a minimum of one, vertical
2" x 4" wall stud.
H Do Not mount microwave oven
to an island or peninsula cabinet.
w The microwave oven top and
rear supporting structures must
be capable of supporting 150 lbs.,
plus the weight of any items
placed inside the microwave
oven or upper cabinet.
Failure to mount the microwave
oven as instructed could result in
personal injury and/or property
damage.
Electrical Shock Hazard
It is the customer's responsibility:
. To contact a qualified
electrical installer.
. To assure that the electrical
installation is adequate and in
conformance with National
Electrical Code, ANSVNFPA 70-
latest edition*, and all local codes
and ordinances.
Failure to do so could result in fire,
electrical shock or other personal
injury.
Tools and
materials needed
Property Damage
Place a portion of carton or another
heavy material over the countertop
or cooktop before installing the
microwave oven. Do Not use a
plastic cover.
Failure to protect cooking surface
or countertop could result in
property damage.
I
NOTE:
Do Not use this microwave oven
for commercial purposes. This
microwave oven is designed for
household use only.
316" and 314"
wood drill bits
Parts supplied
for installation:
saber saw V 6-j ,.
//A
m
4, l/4" x 3"
toggle bolts
69
4 spring
toggle-heads
2, l/4" x 2" bolts
m Take special care when drilling
holes into the wall. Electrical
wires may be concealed behind
the wall covering and contact
with them could result in
electrical shock.
m Locate any electrical circuits
that could be affected by the
installation of this product and
disconnect power circuit.
Failure to do so could result in
electrical shock.
screwdriver
II
-
gq
4,114" x 2" lag screws
&
1, power cord clamp and
1, mounting screw
2 tapping screws
(dark-colored)
(bright-colored)
measuring rape
carton or another heavy material
1 power cord
bushing
l
Copies of the standard listed
may be obtained from:
National Fire Protection Association
Batterymarch
Park
Quincy, Massachusetts
02269
for covering countertop
Special hardware and tools are required
for brick or masonry walls. At least four
anchor bolts must be anchored into the
wall and the mounting area must be
capable of meeting the 150 lb.-weight
requirement.
2 filter screens
Panel A
Advertisement
