Related Manuals for Presentation Switchers PS510
Summary of Contents for Presentation Switchers PS510
-
Page 1: Installation Guide
Presentation Switchers Series 500 Installation Guide PS510 Under Table Presentation Switcher October, 2012 • PN: DOC-000005-00A... - Page 2 Every eff ort has been made to ensure that the informa on in this manual is accurate. Presenta on Switch- ers, Inc., is not responsible for prin ng or clerical errors. Informa on in this document is subject to change without no ce. Page 2 Presentation Switchers, Inc.
-
Page 3: Table Of Contents
Connecting Display or Video Output Devices ................ 9 Connecting Audio Output Devices ..................10 Connecting Control Devices ....................11 Confi guring the PS510 ..............12 The Confi guration Software ....................12 Uploading the Settings ......................14 Save or Retrieve Settings ....................... 14 PS500 Display Control ..............15... - Page 4 Mode ............................19 Testing the Display Codes ...................... 20 Testing the Relays ........................20 Testing the Complete System ....................21 Enabling or Disabling the Display Control Feature ............. 21 Appendix ..................22 Series 500 Programming Codes .................... 23 Page 4 Presentation Switchers, Inc.
-
Page 5: Getting Started
This manual will provide detailed instruc ons to assist an installer with a typical under table in- stalla on of a PS510 presenta on switcher. This process is best outlined by the following steps. 1. Unpack the switcher from the box and separate all components. -
Page 6: Inserting Input Cards
PS510 enclosure to prevent accidental shock to yourself or to the equipment. The drawing below shows a sample layout of a PS510 enclosure. In this case, the system type is a PS510 with HDMI, DVI, and VGA inputs. - Page 7 The following precau ons must be taken. Do not open the protec ve conduc ve packaging un l you have read the following, and are at an approved an -sta c work sta on. Always discharge yourself by touching a grounded bare metal surface before picking up an ESD - sensi ve electronic component.
-
Page 8: Pre-Drill Mounting Holes
WARNING: Keep product away from poten al contact with human legs, knees, and other body parts. A PS510 is made of metal and can harm people if struck with suffi cient force. Pre-Drill Mounting Holes As Shown Pre-Drill Mounting Holes As Shown 1. -
Page 9: Connecting Devices
Connecting Display or Video Output Devices Connecting Display or Video Output Devices The PS510 presenta on switcher is equipped with HDMI and VGA connectors. These connectors are located on the opposite side of the input card assemblies. The HDMI and VGA outputs are simultaneous outputs and output the same resolu ons at all mes. -
Page 10: Connecting Audio Output Devices
Connecting Audio Output Devices Connecting Audio Output Devices The PS510 is equipped with a line level stereo audio output. Line level audio, by default, is a ste- reo audio balanced output. Using the male audio connectors provided (shown below), connect the audio signals as indicated below. -
Page 11: Connecting Control Devices
The serial port is connected directly to the display device. Codes are uploaded and stored in the PS510 using the PS500 Display Control U lity. When the system is shutdown and a input source is selected the projector is sent a “power on” command. When the signal is shut down and signal is lost, the PS510 issues a “power down”... -
Page 12: Confi Guring The Ps510
The Confi guration Software The Confi guration Software The PS510 Confi gura on So ware is available on the website on the PS510 produce web page. This applica on requires a connec on to the PS510 using RS-232. Page 12... - Page 13 The Audio Input Levels feature of the PS510 would allow you to set the audio level of the cable receiver box slightly lower such that all source devices have the same “nominal” level.
-
Page 14: Uploading The Settings
Polling rou nes are costly and o en interfere with the performance or responsiveness of the control panel. Uploading the Settings Uploading the Settings To confi gure the PS510, press the bu on “Program”. This uploads the confi gura on se ngs to the PS510. Page 14 Presentation Switchers, Inc. -
Page 15: Ps500 Display Control
PS500 Display Control The PS510 has a simple control system for controlling a display device (LCD, Plasma, or Projec- tor). The serial port is connected directly to the display device. Codes are uploaded and stored in the Series 500. When the system is inac ve and an input source is selected the projector is sent a “power on”... -
Page 16: Relay Form
Relay Form Relay Form The PS510 does not support relays. This screen is not applicable to the PS510 and was originally designed for the PS500, 7 slot rack mount systems. (Ignore references to Relays.) Contact Action Timing Test Form Test Form Select the Test pull down menu to access this form. -
Page 17: Connecting To The Switcher
Connecting to the Switcher Connecting to the Switcher Connect from a PC to the switcher using a RS-232 straight serial cable. A null-modum cable will not work. Setting Communication Baud Rates Setting Communication Baud Rates Using the Communica ons pull down menu, set the baud rate to the speed of the switcher. The switcher defaults to 115,200 baud. -
Page 18: Input Select
This rou ne is intended to save power and bulb life should a system be le on and nobody using the system - especially if a home room computer goes to sleep and dis- plays a black screen. Page 18 Presentation Switchers, Inc. -
Page 19: Testing The Display Codes
Testing the Display Codes Testing the Display Codes Connec ng Directly to the Display Device Connec ng Directly to the Display Device When tes ng display codes, the PC must be connected directly to the display device using a RS-232 cable. Ensure that the baud rate listed on the main form matches the baud rate of the display. -
Page 20: Appendix
Appendix Series 500 Programming Codes ..................21-22 Page 20 Presentation Switchers, Inc. - Page 21 Series 500 Programming Codes Series 500 Programming Codes Remove all spaces in sending string. “T” is the terminator. A Carriage Return is not required/accepted. Commands follow the AMX/AutoPatch standard of switcher communica ons - when possible. [ ] = Op onal items # = Replace with a number | = OR Input / Source Select...
- Page 22 Video image is restored. Power Saving Mode Enable power savings mode. RST is only way to return to normal operation. Examples Send Response None Put PS510 in power savings mode. Reset System Reset System. Reboot. Examples Send Response None Performs soft reset on system and hard reset on cards.
- Page 23 Presentation Switchers 15364 E. Valley Blvd City of Industry, CA 91746 United States of America www.Presenta onSwitchers.com US/CAN Toll Free: 800-614-9958 Voice: 909-829-5724 Fax: 909-532-5234 Series 500 Installation Guide Page 23...
Need help?
Do you have a question about the PS510 and is the answer not in the manual?
Questions and answers