Advertisement
OPERATING INSTRUCTIONS:
Using the Control Panel (See Fig. 3 Below):
Master Power Switch (A):
• Push button A to turn electric fireplace on. (Ensure that the red power light
"B" above the Master Power Switch is on - this confirms that the unit is plugged
in. It will turn from red to green when the Master Power Switch is pushed.
• The flame effect will automatically come on when the electric fireplace is on.
Fan Button (C):
• This is a High and Low setting for the fan and the heater. Note that the fan will
only come on if the thermostat temperature is set above the room temperature.
• The fan light (D) denotes the Low fan setting and the fan light (E) denotes
the High setting.
Timer (F):
• If a timer is desired, push this button once for a 1 hour timer, twice for a 2
hour time, etc (up to 12 hours). The time will show on the digital readout
screen. To reset, keep pushing the Timer button (F) until it returns to your
desired time setting. (Note that the timer is approximate and extreme caution
is necessary when the electric fireplace is left operating and unattended. Keep
children, invalids and and pets away from the unit when in use.)
Temperature Buttons - Increase (G) and Decrease (H):
• This electric fireplace is equipped with a thermostat. Press the Temperature
Button (G) to increase the temperature. Press the Temperature Button (H) to
decrease the temperature. (The electric fireplace heater and fan will only turn
on if the temperature setting is higher than the room temperature.)
The Temperature Digital Readout Screen (I):
• This screen shows the current setting of the thermostat in Celcius or
Fahrenheit degrees. See Button (L) to adjust the setting to C or F.
• Press on the "°C/°F" Button (L)on the control panel for 3 seconds and after
a short " beep" sound, the displayer will show the real room temperature for
5 seconds
• This screen will turn off after 5 minutes if there is no temperature adjustments.
• The temperature light (J) indicates if the digital reading is in Fahrenheit
and the temperature light (K) indicates the digital reading is in Celcius
NOTE: The fan will continue to work for several minutes when the heaters
turns off. This allows the infrared components inside the heater to cool
down.
Control Panel:
B
D
E
C
Call 1-877-744-3649 for assistance or email us at service@phoenixinno.com
FIG. 3
I
K
J
F
L
G
H
MC
Using the Remote Control:
This heater includes a remote control. To operate the appliance using the
remote control, ensure the red power light "B" is on. Each remote control is
shipped with a plastic tab inserted into the battery chamber to prevent
damage and power loss. Pls remove by pulling on the tab out of the
chamber. (See Maintenance Section). See below for directions to use the
remote control:
On/Off Button (N):
N
Push button N to turn
•
electric fireplace on.
O
Child Lock Feature (R):
Push this button (R)
•
once to unlock the control
panel functions and
P
remote control functions.
Please note that the
heater will automatically
R
lock the heater after 8
seconds without any
operations.
NOTE: If the remote controller is lost, please press on the Power switch
on the control panel for 3 seconds, the control will unlock after a short
"beep" sound."
Celcius / Fahrenheit Setting Button (T):
• Push the button (T) to change the heat readout settings.
Temperature Buttons - Increase (Q) and Decrease (P):
• This electric fireplace is equipped with a thermostat. Press the Temperature
Button (Q) to increase the temperature. Press the Temperature Button (P) to
decrease the temperature. (The electric fireplace heater and fan will only turn
on if the temperature setting is higher than the room temperature.)
ESO Button Energy Savings Option (U):
• Push this button (U) once to move the temperature setting easily to 68
degrees F (20 degrees C).
• Push the ESO Button (U) an additional time to release the appliance from
the Energy Savings Option.
NOTE: Direct the remote control at the appliance from 1 to 5 meter
distance for the remote control to function properly. The remote control
receptor is located in the control panel (Fig 1)
NOTE: For remote control battery replacement, use Lithium Cell CR2025 3V.
4
FIG. 4
Fan Button (S):
S
This is a High and Low
•
setting for the fan and
the heater. Note
that the fan will only
T
come on if the thermostat
temperature is set above
the room temperature.
Q
U
Advertisement
