Standard Horizon RAM3 Owner's Manual

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference including received, interference
that may cause undesired operation.
I A
NCLUDED CCESSORIES AND REPLACEMENT PART NUMBERS
1. 23-Foot Routing Cable (S8101512)
2. Rubber Cap (RA052520A)
3. Mounting Bracket (RA052510) & Screws (U24312020 x 4 pcs)
4. Microphone Hanger (RA458800: Black or RA436000: White) &
Screws (U40412220 x 2 pcs)
5. Ferrite Core (L9190182)
1
3
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD ( AUSTRALIA ) PTY., LTD.
Normanby Business Park, Unit 14/45 Normanby Road
Notting Hill 3168, Victoria, Australia

Declaration of Conformity

We, YAESU UK LTD. declare under our sole responsibility that the following
equipment complies with the essential requirements of the Directive 1999/5/EC.
Type of Equipment: Handset
Brand Name: STANDARD HORIZON
Model Number: CMP30
Manufacturer: Vertex Standard Co., Ltd.
Address of Manufacturer: 4-8-8 Nakameguro Meguro-Ku, Tokyo 153-8644, Japan
Applicable Standards:
This equipment is tested and conforms to the essential requirements of direc-
tive, as included in following standards.
EN 301 843-1 (2004-06)
EMC Standard:
EN60950-1:2006
Safety Standard:
The technical documentation as required by the Conformity Assessment pro-
cedures is kept at the following address:
Company: YAESU UK LTD.
Address: Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Disposal of your Electronic and Electric Equipment
Products with the symbol (crossed-out wheeled bin) cannot be
disposed as household waste.
Electronic and Electric Equipment should be recycled at a facil-
ity capable of handling these items and their waste byproducts.
In EU countries, please contact your local equipment supplier representative
or service center for information about the waste collection system in your
country.
2
4 5
Copyright 2011
VERTEX STANDARD CO., LTD.
All rights reserved.
No portion of this manual
may be reproduced
without the permission of
VERTEX STANDARD CO., LTD.
E A G 3 6 X 1 0 1
RAM3 CMP30
Remote Station Microphone
The RAM3 ( CMP30 ) allows you to remotely control all functions of Standard Horizon
fixed mount VHF radios which include the Quantum series, Matrix series, Quest-X,
Quest+, PS1000 and PS2000. The full dot matrix display and programmable keys
make operation simple and fast. Additional features include turning the radio on/off
and all DSC functions including Distress. When connected to the Matrix GX3000S, or
the Quantum series, this remote station microphone also controls the 30W PA/hailer
functions. The RAM3 ( CMP30 ) can be extended up to 70 feet using the optional CT-
100 (23 Foot) extension cable. The RAM3 ( CMP30 ) is backed by an industry leading
3-year waterproof warranty.
Owner's Manual
The details of the installation and operation of the RAM3 ( CMP30 ) is included
in the owner's manual of the compatible fixed mount radio, or it can be down-
loaded at www.standardhorizon.com. If you have any questions or comments,
please contact Standard Horizon Marine Product Support at 800/767-2450.
RAM3 CMP30 I
1. Connect the Extension Cable to the 8-pin connector on the transceivers rear panel,
then tighten the Cable Nut (Figure 1).
2. Referring to Figure 2, attach the supplied ferrite core as close as possible to the MIC
plug of the Routing Cable and External Speaker Connections, then snap its two
halves together. And then, wind some plastic tape around the ferrite core, to prevent
vibration from causing the two halves to split apart and fall off the wires.
3. Referring to Figure 3, make a 1.2" (30 mm) hole in the wall then insert the Exten-
sion Cable into this hole. Connect the Gasket and Mount Base to the Extension
Cable Connector using the Nut.
4. Drill the four Screw holes (approx. 2 mm) on the wall then install the Mounting
Bracket to the wall using four screws.
5. Put the Rubber Cap on to the Nut.
6. The installation is now complete. Connect the RAM3 ( CMP30 ) to the Extension
Cable Connector and tighten the Cable Nut.
F 1
IGURE
External Speaker
Ferrite Core
Connections
Snap together
Routing Cable or
CT-100 Extension Cable
As close as possible
F 2
IGURE
The routing cable can be cut and spliced, however care needs to be
taken when reconnecting the wires to ensure water integrity.
Before cutting the cable make sure it is not plugged into the radio. After
cutting you will notice there are the following wires:
Yellow, Green, Brown, Purple, Blue, Green, Red , and Shield
The Red and Shield wires are wrapped in foil. Remove the foil, and
separate the Red and Shield wires.
NSTALLATION
External Speaker Connections
Ferrite Core
Gasket
Wall
Routing Cable
Mounting Bracket
Nut
F 3
IGURE
NOTE
Cap