Sub-Zero Undercounter Ice Machine Installation Manual
Hide thumbs
Also See for Undercounter Ice Machine:
- Installation manual (16 pages) ,
- Installation & operation manual (32 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sub-Zero Undercounter Ice Machine
Summary of Contents for Sub-Zero Undercounter Ice Machine
-
Page 1: Undercounter Ice Machine
INSTALLATION GUIDE Undercounter Ice Machine... -
Page 2: Table Of Contents
Contents Important Note Undercounter Ice Machine ..... 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Ice Machine Specifications . -
Page 3: Undercounter Ice Machine
The homeowner should keep this installation guide for future reference. Any questions or problems regarding the installation should be directed to your authorized Sub-Zero dealer or Sub-Zero customer care at 800-222-7820. You may also check the contact & support section of our website, subzero.com. -
Page 4: Ice Machine Specifications
Ice Machine Specifications Ice Machine Specifications OVERALL DIMENSIONS INSTALLATION " 23" (375) (584) TOP VIEW 24" (610) OPENING DEPTH " (854) 4" (102) 24" " " (610) (876) OPENING DEPTH OPENING (387) OPENING HEIGHT WIDTH 18" (457) SIDE VIEW FRONT VIEW 6"... - Page 5 Ice Machine Specifications subzero.com/specs Electrical Requirements The ice machine must be installed with adequate clear- The electrical supply for the ice machine must be installed ance for electrical connection at the rear of the unit. The by a qualified electrician in accordance with all applicable electrical supply for the ice machine requires installation of national and local electrical codes.
-
Page 6: Plumbing Requirements
Ice Machine Specifications Plumbing Requirements The ice machine must be installed with adequate clear- WATER SUPPLY LINE ance for water and drain connections at the rear of the For all ice machine models, locate the water supply line as unit. Prepare the water supply line and drain connection shown in the illustration below. - Page 7 The ice machine control board will monitor water usage and indicate when replacement is required. AIR GAP Replacement water filters are available through your authorized Sub-Zero dealer. For local dealer information, DRAIN TUBE visit the find a showroom section of our website, WATER WATER subzero.com.
-
Page 8: Ice Machine Installation
Ice Machine Installation Installation Requirements Installation • Installation must allow removal of the ice machine for Before moving the ice machine into position, make sure all cleaning and service. Service diagnostics are per- opening dimensions, electrical and plumbing requirements formed from the top of the ice machine. are complete and accurate. - Page 9 Ice Machine Installation subzero.com/specs Installation 8) Move the ice machine into its final position. INSTALL THE ICE MACHINE 1) Adjust the leveling legs close to the desired height. 9) Secure the ice machine by installing two #8 x " flat Refer to the illustration below.
- Page 10 Ice Machine Installation Reverse Door Swing The hinged side of the door may be reversed to the other 2) Remove the hinges from the door by removing the four side if needed. screws (two per hinge) that secure the hinges to the door.
-
Page 11: Ice Machine Installation
Ice Machine Installation subzero.com/specs Reverse Door Swing 5) Remove the ice machine top cover by removing the 8) Remove two screws from the lower edge of the bottom two screws along the back of the unit. Refer to the trim plate and slide the trim plate to the right, to cover illustration below. - Page 12 " (772) for panel specifications. If you have questions, contact Minimum Thickness " (16) your authorized Sub-Zero dealer or cabinet supplier. Maximum Weight 15 lbs (7 kg) For door handle hardware, a D-style pull, centered on the Dimensions based on "...
- Page 13 Ice Machine Installation subzero.com/specs Panel Installation Installation INSTALL KICKPLATE Once the ice machine is in position, install the kickplate Exercise caution when drilling holes for mounting using the screws provided. The kickplate must be hardware. This is especially critical with inset panels. removed for servicing.
-
Page 14: Installation Checklist
Ice Machine Installation Installation Installation Checklist To ensure a safe and proper installation, the following 90° DOOR STOP checklist should be completed by the installer to ensure Door stop pins provided with the ice machine will limit the that no part of the installation has been overlooked. door swing to 90°. -
Page 15: Service Information
Location of rating plate. The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero, Inc. ©Sub-Zero, Inc. all rights reserved. - Page 16 SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820 7024818 REV-A 2/ 2012...