1. Manuals
  2. Brands
  3. Yeti Communications Manuals
  4. Radio
  5. Huracan HR-07-NZ
  6. Owner's manual

Yeti Communications Huracan HR-07-NZ Owner's Manual

10 meter amateur radio
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Summary of Contents for Yeti Communications Huracan HR-07-NZ

  • Page 2 CONGRATULATIONS on your purchase of a HURACAN HR-07-NZ 10meter amateur radio. Your HURACAN HR-07-NZ transceiver radio is designed to provide trouble-free service and state of the art, high performance SSB communications. This radio has been designed with the SSB eenthusiast in mind incorporating new circuitry for increased SSB stability and improved SSB audio.

  • Page 3: Specifications

    SPECIFICATIONS: HR-07-NZ 10 METER HF MOBILE TRANSCEIVER GENERAL Frequency Range: 10m Band 28.000-29.995 MHz. Export 25.000-29.995 export (5 bands 1mhz ea) NZ CB 26.330-26.770 40ch CB Band with channel readout Frequency Control: Phase Lock Loop (PLL) synthesizer. Frequency Tolerance: 0.005% Frequency Stability: 0.001% Operating Temp.
  • Page 4 TRANSMITTER Power Output (Max): 10w Carrier/50W PEP 50W PEP Modulation: AM = Class B Amplitude. FM = 2.5Khz @ 20mV 1Khz Audio in Spurious Emission -60dB AF Modulation Response AM / FM 450 – 2500 Hz RECEIVER Circuit Type : Dual-Conversion Superheterodyne Intermediate Frequencies : 1st IF / SSB IF ..
  • Page 5 Use 12-gauge wire on longer runs. Attach the mounting bracket to the vehicle first then mount the Huracan HR-07-NZ to the bracket. If the rear panel is not accessible you may want to attach the power and antenna cable prior to mounting.
  • Page 6 28.000mhz requires a longer antenna than Connect the PL-259 to the antenna connector 29.700mhz, because it is lower in frequency. on the rear panel of the Huracan HR-07-NZ. Due to the various methods of adjusting Make sure that the cable does not interfere with antennas for proper SWR we have chosen what the safe operation of the vehicle.
  • Page 7 Typically the vehicle’s ignition system or more pliers. specifically the alternator generates this TIPS for Antenna Adjustment noise. The Huracan HR-07-NZ is equipped with IF YOU ARE HAVING DIFFICULTIES IN a noise blanker circuit that is designed ADJUSTING YOUR ANTENNA...

  • Page 8: Front Panel Controls

    FRONT PANEL CONTROLS: 1. 2-DIGIT CHANNEL DISPLAY Displays operating channel does not display when in Free-band mode.Will display when in 10 meter mode (see options list) or N.Z auto select mode (see control #7). 2. VFO CONTROL: Rotate clockwise to increase frequency or counter-clockwise to decrease frequency. 3.
  • Page 9 11. R.F Power am/fm only: Variable RF Output Power. The transmitted power of the Huracan HR-07-NZ may be varied from 0 to 50 watts peak in Am/Fm modes. Rotate clockwise to increase RF output power. Rotate counter-clockwise to decrease RF output power .Variable 1-10 watts carrier Am Mode /1-50 watts...
  • Page 10 15. Rodger Beep: Activates the end of transmission, or roger beep, tone. When activated a 1 kHz tone will automatically transmit upon release of PTT switch .This notifies contacts that your transmission has ended and you are ready to receive their signal 16.

  • Page 11: Rear Panel Details

    3. Public Address (PA) Horn Jack A PA horn jack is located on the rear panel of the transceiver. The Huracan HR-07-NZ is designed to accept any standard PA horn for use with two-way transceivers. To operate in PA mode, please refer to the previous instructions.
  • Page 12 USING YOUR RADIO FOR THE FIRST TIME : PROCEDURE TO RECEIVE 1. Turn unit on by tuning ON / OFF VOLUME control clockwise. 2. Set the VOLUME for a comfortable listening level. 3. Set the MODE switch to the desire mode. 4.
  • Page 13 MICROPHONE PLUG REASSEMBLING: 1. Remove the retaining screw. 2. Unscrew the housing from the pin receptacle body. 3. Loosen the two cable clamp retainer screws. 4. Feed the microphone cable though the housing, knurled ring and washer shown in FIG. 3. The wires must now be soldered to the pins as indicated in the FIG.

  • Page 15: Receiving Ssb Signals

    Receiving SSB Signals There are four types of signals presently used for communications in an Amateur band: AM, FM, USB and LSB. When the MODE switch on your unit is placed in the AM position, only standard double sideband and in FM position, only frequency deviation, full carrier signals will be detected. An SSB signal may be recognized while in the AM or FM mode by its characteristic “...

  • Page 16: Options List

    OPTIONS LIST Introduction: The HURACAN HR-07-NZ is programmed for the 10 Meter Amateur Band out of the box, and covers a range of 28.000 -29.695 MHz in 5 khz steps standard. The frequency range can be extended for Export Use in 6 Band segments OF 1MHZ each containing 200 Channels (200 X 5KHZ STEPS= 1MHZ).

Table of Contents