Related Manuals for Allnet ALL0239-3G
Summary of Contents for Allnet ALL0239-3G
-
Page 1: User Manual
ALL0239-3G Wireless-N Router ALL0239-3G 3G Mobile Broadband plus 4-Port Wireless-N Router User Manual ALLNET GmbH – www.allnet.de... -
Page 2: Table Of Contents
User Manual Table of Contents About the Product ......................... 3 Features..........................4 Requirements ........................5 Package Content ........................6 Device Design ........................7 Getting Started ........................10 Plan Your Network....................11 Remove or Disable Conflicts ................... 12 Installing your Router ....................13 Connecting to the Internet .................. -
Page 3: About The Product
Easy to install and Use By connecting a HSDPA USB modem into USB port of ALL0239-3G, Internet access can be accessed and shared virtually anywhere within a wire or wireless broadband network. You can also directly connect Ethernet-based devices to its built-in 4-port full-duplex 10/100 switch. -
Page 4: Features
User Manual Features 2-in-1 dual function Router - HSPA support for 3G mobile broadband plus 4-port wireless N router Support HSDPA/HSUPA (3.5G) USB modem connection - to offer a network connection with full mobility Converts single user 3G USB modem into a multiple users ready WiFi Router - to share the mobile Internet connection with your family, friends and colleagues Support IEEE802.11b/g and 11n (draft 2.0) wireless standard - data transfer rate reaches up to 300Mbps... -
Page 5: Requirements
User Manual Requirements Your computer must meet the following minimum requirements. Internet Explorer 7 or Mozilla 3.0.5 CD-ROM Drive Ethernet network adapter Page 5 of 47... -
Page 6: Package Content
User Manual Package Content The package should contain the following items: ALL0239-3G • CD Content • 12.0V, 1A Power Adapter (Model SWM11-12120) • Easy Start Guide • If any of the items is missing please contact the dealer from whom the equipment was purchased. -
Page 7: Device Design
User Manual Device Design Front Panel Behavior Description UMTS 3.5G Easy Connect and Disconnect to your 3.5G Connect/Disconnect Button broadband. No power is supplied to the device. Power Steady Connected to an AC power source. Light UMTS (3.5G) Internet connection is active UMTS (3.5G) Internet connection is off Active USB device is connected to the router No active USB device connected to the router... - Page 8 User Manual Connected to a Modem No Modem connection Connected to an Active Ethernet Device Ethernet 1-4 No Ethernet Connection Blinking Transmitting/Receiving Data Press for two seconds (or until the LED blinks) to start WPS pairing. Wireless client must be WPS-enabled and must be pressed within 2 minutes.
-
Page 9: Back Panel
User Manual Back Panel Label Description Ethernet Port 1-4 Connecting with computers/devices using an Ethernet cable Connect to a modem using an Ethernet cable Reset Press for 3 seconds to reset to the Factory Default. Connect to a 3G USB modem stick, USB storage, USB Port printer and alike. -
Page 10: Getting Started
User Manual Getting Started Plan your Network You may need to check Remove/Disable some setting or disable some application before Conflicts installation. Connect the modem, computer, and power Setup the adaptor to the router. Router Open a browser to access the Web User Interface Connect to the and then use Setup... -
Page 11: Plan Your Network
User Manual Plan Your Network 1. Using a 3G USB Modem Stick 2. Using a DSL/Cable modem Page 11 of 47... -
Page 12: Remove Or Disable Conflicts
User Manual Remove or Disable Conflicts To make sure the router installation moves on smoothly, you need to remove or disable conflicts that may interfere the installation. Probable conflicts may include: Internet sharing applications • Proxy software • Security software •... -
Page 13: Installing Your Router
User Manual Configuring Internet Properties To set the Internet Properties: 1. Click the Start button, and then click Run. This opens the Run dialog box. 2. Type in inetcpl.cpl, and then click Ok. This opens the Internet Properties. 3. Click the Connections Tab. 4. -
Page 14: Connecting To The Internet
User Manual Using a DSL or Cable Modem If you choose to use a DSL or Cable modem you are required to have the following: DSL or cable modem Active Internet Account 1. Connect your DSL or Cable modem to the router’s WAN port using an Ethernet cable. 2. - Page 15 Active Internet Account 7. UMTS 3G connection Please connect your USB modem stick to ALL0239-3G and make sure that your data SIM card is properly inserted to the modem. 3G Access Point Settings – Choose between List and Manual. List will provide the APN set by your Internet Service Provider.
- Page 16 User Manual Username and Password – Some ISP may require a Username and Password set by the Operators. Please contact your ISP if you don’t have this information Choose your preferred Connection Method Connect Manually – This connection method requires you to manually press the ‘Connect’...
- Page 17 User Manual 8. WAN Connection Please connect your DSL or Cable modem to ALL0239-3G WAN port using an Ethernet cable, make sure that you have an active Internet account. Connection Type Static IP – select this if your ISP provides you the IP address, Subnet mask, Gateway and DNS server addresses.
- Page 18 9. Setup your wireless connection, tick Wireless Enabled to activate your wireless connection and set the SSID for your ALL0239-3G. Click Next to continue. 10. Under Summary page verify the settings made then click ‘Apply’ for the settings to take effect.
-
Page 19: Wps (Wi-Fi Protected Setup)
User Manual WPS (Wi-Fi Protected Setup) WPS button allows you to activate Wi-Fi Protected Setup (WPS). When you press the WPS button it automatically detects and connects wireless clients into the wireless network by broadcasting the wireless network settings from your Access Point to you wireless device/s. To setup WPS: 1. -
Page 20: About The Web User Interface
User Manual About the Web User Interface To Access the Web User Interface When you router is already setup open your Web Browser and on the Address bar type in http://192.168.1.1 Username: admin Password: admin The WEB GUI includes the following settings for your router: Basic Mode •... -
Page 21: Basic Mode
This pane will show you the Internet connection type and status of your ALL0239-3G. Local Network This pane will show you the lists of the clients that are connected to your ALL0239-3G. Storage This pane will show you the status of the mass storages that is connected to your ALL0239- 3G. -
Page 22: Printer
Printers using the USB port come with a software installation CD for installing the printer drivers and applications. The drivers for the printers must be installed on the computer first to prepare it to use the printer when it’s connected to the ALL0239-3G. Refer to the printer’s documentation on how to install the drivers. - Page 23 User Manual 2. Click on the File Menu > Add Printer. 3. Click on Next on the Add Printer Wizard page. 4. Choose Local Printer attached to this computer and click Next, on the Local or Network Printer page. Page 23 of 47...
- Page 24 5. Choose Create a new port and on the drop down box choose Standard TCP/IP Port then click Next. 6. Click Next button on Welcome to the Add Standard TCP/IP Printer Port Wizard. 7. Enter your ALL0239-3G’s Default Gateway IP address 192.168.1.1 then click Next. Page 24 of 47...
- Page 25 User Manual 8. Under Additional Port Information Required choose Custom then click Next 9. Once the computer detects the printer on the Print Server, it will ask for the printer manufacturer and model, a list of printers will be shown, select the your printer from the list and click OK.
-
Page 26: For Windows Vista
User Manual 11. Click Finish to complete the installation. PRINTING A TEST PAGE AFTER INSTALLATION 1. Open the Printers and Faxes page from Control Panel. 2. Right click on the new printer and click on Properties. 3. Click on the Print Test Page button on the Printer properties page, the test page will be printed on the network printer. - Page 27 User Manual 3. Click on Add a Printer. 4. Click on Add a local printer then click Next. Page 27 of 47...
- Page 28 User Manual 5. Select Create a new port, on the drop down box choose Standard TCP/IP port then click Next. 6. Enter the Default Gateway IP address of your ALL0239-3G router 192.168.1.1 then click Next. Page 28 of 47...
- Page 29 User Manual 7. Under Additional Port Information Required window, select Custom then click Next. 8. Once the computer detects the printer on the Print Server, it will ask for the printer manufacturer and model, a list of printers will be shown, select the your printer from the list and click OK.
- Page 30 User Manual 9. Select Use the driver that is currently installed then click Next. 10. To print a test page click on Print a test page on the confirmation screen, click Finish to complete the installation. Page 30 of 47...
- Page 31 Apply. Note: Scanning, Faxing and Photocopying functions on Multifunction printers are currently not supported on the ALL0239-3G, Print function is the only feature that will work on these printers type when connected to the ALL0239-3G. Page 31 of 47...
-
Page 32: Wizard
User Manual Wizard This section will guide you on how to configure your ALL0239-3G to have an Internet connection. Language and Time Zone Select the Language and Time zone from the drop down box then click Next to continue. Internet Connection Type Select the Internet Connection type then click Next to Continue. -
Page 33: Wan Connection
User Manual Connect Manually – you need to press the Connect button each time Internet connection is • required. Always connected – Internet connection is always ON. You need to manually press the • disconnect button when Internet connection is not required. WAN connection On this section you can choose your Internet connection type from Static IP, PPPoE and DHCP. - Page 34 WPA Enabled - tick the box if your want to enable your wireless security. This will ensure wireless security on your network. e.) Passphrase - Enter the password that is required by your ALL0239-3G to connect via wireless. Summary This section will display the entire configuration that was set on your ALL0239-3G.
-
Page 35: Quick Setup
User Manual Quick Setup This section allows you to change the current settings of your ALL0239-3G without going to the step-by-step procedure on how to establish an Internet connection. Language and Time Zone This pane displays the time that you set on your ALL0239-3G. Configure the settings then click the Apply button for the changes to take effect. -
Page 36: Advanced Page
Router Subnet Mask – this is the router’s subnet mask. • DHCP Enabled- Your ALL0239-3G has a built in DHCP server. Your ALL0239-3G will • automatically assign an IP address to all the computers that will connect to your network. -
Page 37: Internet
User Manual Internet This section allows you to choose the Internet connection type that you would like to use. UMTS (3G) 1. 3G Access Point Settings –Choose between List and Manual. List will provide the APN set by your Internet Service Provider. Choose your Country, Internet Service Operator and the APN. Manual you need to manually key in the APN provided by your ISP. -
Page 38: Wireless
• SSID- this is your ALL0239-3G wireless network name. • Broadcast SSID- Uncheck the box to hide your ALL0239-3G wireless network name. • Wireless Mode – select the wireless connection mode on the drop down menu list. By default •... -
Page 39: Security
Select this if you want your wireless security to be disabled, it is advisable to Enable your wireless security to avoid unauthorized access to your network via wireless. • Set the WEP key on the required field. This is the password that your ALL0239-3G will require to connect to it via wireless. WEP default key You may choose from Hex to ASCII key format for your WEP key. -
Page 40: Port Forwarding
Filtering This section allows you to configure MAC filtering, IP filtering and URL filtering. By default ALL0239-3G will block all the MAC Addresses, IP Addresses and URL from accessing the specific rule/port set on the router. MAC Address Filtering This section enables both Port and MAC filtering. -
Page 41: Ddns (Dynamic Dns)
User Manual Note: All incoming access on your network is blocked. If you want to have an access within your network from WAN please use Port Forwarding. URL Filtering This section allows you to control the access to a certain Websites on the Internet by entering URL name on the required field. -
Page 42: Settings
User Manual Settings This section allows you to Back up, Save and Restore to factory default the router’s configuration. Backup Click the ‘Backup’ button to save the current settings of your router. If you will change the current configuration of your HW500-3G it is recommended that you backup the router’s current settings. -
Page 43: Reboot
User Manual Reboot Click the ‘Reboot’ button to reboot the device Page 43 of 47... -
Page 44: Password
User Manual Password This section allows you to change the default password setting of the router to access the Web GUI. Enter the new password then click apply. Page 44 of 47... -
Page 45: Regulatory Compliance Notices
User Manual Regulatory Compliance Notices European Regulations The product has been designed, tested and manufactured according to the European R&TTE directive 1999/5/EC. Page 45 of 47... - Page 46 The safety advice in the documentation accompanying the products shall be obeyed. The conformity to the above directive is indicated by the CE sign on the device. The ALL0239-3G 3G-Mobile Broadband plus 4-Port Wireless-N Router conforms to the European Directives 1989/336/EEC.
- Page 47 All other company or product names mentioned are used for identification purposes only and may be trademarks of their respective owners. Manufacturer: ALLNET GmbH ALLNET Deutschland GmbH Maistrasse 2 82110 Germering Tel. +49 89 894 222 22 Fax +49 89 894 222 33 E-Mail: info@allnet.de...
Need help?
Do you have a question about the ALL0239-3G and is the answer not in the manual?
Questions and answers