Auto Standby - Onkyo TX-NR609 Instruction Manual

■
HDMI Through
Off
Auto:
Detects the signal and automatically selects the input
source.
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,
AUX, TV/CD, PORT:
Selects the input source for which the HDMI
Through function is enabled.
Last:
The HDMI Through function is activated on the
input source selected at the time of setting the AV
receiver to standby mode.
When enabling the HDMI Through function, regardless of
whether the AV receiver is on or in standby, both audio
and video streams from an HDMI input will be output to
the TV or other components via HDMI connection. The
HDMI THRU and HDMI indicators light when enabled
(HDMI is dimly-lit).
This setting is set to "Auto" automatically when the above
"HDMI Control (RIHD)" is set to "On".
Note
• Only the input source assigned to the HDMI IN via "HDMI
Input" is enabled (➔ page 44).
• The power consumption during standby mode will increase
during the HDMI Through function; however in the following
cases, the power consumption can be saved:
– The TV is in standby mode.
– You are watching a TV program.
• Refer to the connected component's instruction manual for
details.
• Depending on the connected component, the correct input source
may not be selected with the setting set to "Auto".
• This setting is set to "Off" automatically when the "HDMI
Control (RIHD)" setting is set to "Off".
■
Audio TV Out
Off
On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV's speakers.
Normally, this should be set to "Off".
Note
• If "On" is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, "TV Speaker" appears on the display by pressing
DISPLAY.
"
• When HDMI Control (RIHD)
" "
fixed to Auto .
• With some TVs and input signals, no sound may be output even
when this setting is set to " On
• When "Audio TV Out" or " HDMI Control (RIHD)" is set to
" On " and you're listening through your TV's speakers
(➔ page 17), turning up the AV receiver's volume control will
make the sound be output from the AV receiver's front left and
right speakers. To stop the AV receiver's speakers producing
sound, change the settings, change your TV's settings, or turn
down the AV receiver's volume.
" " "
is set to On , this setting is
" .
■
Audio Return Channel
Off
Auto:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT of
the AV receiver. To use this function, you must select the
TV/CD input selector and your TV must be ARC capable.
Note
• If you set "Audio Return Channel" to "Auto", the "Audio
Selector" settings of the TV/CD input selector will be
automatically switched to "ARC"
• The "Audio Return Channel" setting can be set only when the
"HDMI Control (RIHD)" setting is set to "On".
• This setting is set to "Auto" automatically when the "HDMI
Control (RIHD)" is set to "On" for the first time.
■
Lip Sync
Off
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
After changing the settings of the
(RIHD) " , " HDMI Through
Channel" turn off the power on all connected pieces of
equipment and then turn them on again. Refer to the
user's manuals for all connected pieces of equipment.

Auto Standby

■
Auto Standby
Off
On
When "Auto Standby" is set to "On", the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video
signal input.
"Auto Standby" will appear on the display and OSD 30
seconds before the Auto Standby comes on.
Default setting: On (European, Australian and Asian
models), Off (North American and Taiwan models)
Note
On"
• Set to " , the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2 is on.
(➔ page 54).
" HDMI Control
" or "Audio Return
En
57