Edge Products CS Quick Install Manual

CS/CTS QUICK INSTALL INSTRUCTIONS
Step 1: Locate the OBDII Port
Supplied Items Suggested Tools
The OBDII port is a 16-pin connector like the illustration be-
1. CS or CTS Device • Flat head screwdriver
low.
2. Arkon Windshield Mount
3. OBDII Cable
4. Mini USB Cable
5. Alcohol Wipe
6. Zip Tie Packet
1
2 3
4 5
6
OBDII LOCATIONS
Step 2: Connect/Route the OBDII Cable
Remove the panel on the
side of the dashboard to
provide access to route
the OBDII cable from the
OBDII port up to the top
of the dash.
OBDII PORT
*On some vehicles you may also
need to remove the panel directly
The OBDII port is located un-
under the steering wheel.
der the dash below
the steering wheel.
The OBDII port is
placed in different
locations under the
Once you've removed
dash for different
the necessary panels,
applications; refer to
connect the OBDII
the OBDII port loca-
cable to the OBDII
tion drawing (left) to
port, and route the
help you locate your
cable under the dash,
OBDII port. If you are
out the side panel, up be-
unable to locate your
tween the door seal trim
OBDII port, there may
and the edge of the dash.
be a sticker underneath
Tuck the cable back as far
*Note: Leave 6-10"
the steering column that may of cable exposed on
as you can as you route it
top of the dash so you
explain where your OBDII is
up to the dash.
have room to posi-
located.
tion the device.
Step 3: Position the Device Step 4:
Before you attach the
suction cup portion of the
Position the device
mount to the window at-
and the mount on
the windshield in the tach it to the device. Insert
desired location. the tabs on the mount into
Pay attention to the slots on the back of the
device and slide up (CTS)
where the suction
or to the side (CS) until it
cup will mount on the
stops.
windshield.
*The mounting tabs are a tight fit by
design to maintain a solid connection.
Once you've identified
the suction cup position
on the windshield, use
the supplied alcohol wipe
to thoroughly clean the
area. After you've wiped
the area clean, let it dry
for 2-3 minutes.
Connect the Mount and OBDII Cable Step 5: Position and Lock the Device on theWindshield
Once the alcohol has dried
you're ready to attach the
mount to the wind-
shield.
You'll notice that the mount has
a locking tab. This tab creates the
suction that will lock the mount
to the windshield. Make sure
the lock is in the "Unlocked"
position. Position the
mount where you've
cleaned the windshield,
press firmly, and push the tab to the
"Locked" position.
Next, insert the connector on the end
of the OBDII cable into the 16-pin
Once you've locked the mount to
connector on the back of the device
the windshield, use the adjustment
(this is easier if done prior to mount-
knobs to fine tune the viewing angle
ing the device on the window). The
and height of the the CTS/CS device.
connector only fits one way so be
sure that the locking tab is on the
bottom.
Note: The device will power on
automatically when it detects your
vehicle has started. If you wish to
power up the device without starting
your vehicle, ensure the key is in the
run position and touch the screen
(CTS) or a button (CS).
UNLOCKED
LOCKED
VERTICAL ADJ.
KNOB
This knob will allow you
to adjust the viewing
angle and height of the
device up or down.
VARIABLE ANGLE ADJ
KNOB
This knob will allow you to ad-
just the viewing angle of the
device in both horizontal and
vertical fashions. Use it to fine
tune your viewing angle.