Related Manuals for Navico WM-2
Summary of Contents for Navico WM-2
- Page 1 Installation Manual Navico WM-2 Sirius Satellite Weather & Radio Module English www.northstarnav.com. www.simrad-yachting.com Brands by Navico - Leader in Marine Electronics...
- Page 2 Please place the ESN sticker in the box below WM-2 – WEATHER/RADIO MODULE This ESN number is P/N: 000-10036-001 important. You will need it to activate S/N: 010036MMDDYYNNNN SIRIUS services see page 20 Contact SIRIUS at 1-800-869-5480...
-
Page 3: Preface
Preface FCC Statement This equipment has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio... -
Page 4: Table Of Contents
Pedestal mount ........... 10 Surface mount ..........11 Installing the weather module ....12 Mounting Location ........12 Wiring the WM-2 Weather Module ....13 Wiring guidelines ........13 Connectors overview ........13 Connect Power ........... 14 Audio connection ........16 Connecting to your display ...... - Page 5 Check status of the SIRIUS service..18 Simrad GB40 ..........19 SIRIUS activation ........20 Spare parts ..........21 Troubleshooting .......... 22 LED Information ......... 22 Module Data Retention ......... 23 Specifications ..........24 Dimensions ..........25 Preface | 5...
-
Page 6: Disclaimer
Disclaimer As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance. -
Page 7: Introduction
Introduction The Navico Satellite Weather Module (000-10036-001) is compatible with the following Navico displays: GB40 Functionality cross reference Display system Weather Satellite radio Simrad NSE GB40 *Some feature functionality could be limited depend on region. Parts List Part Number Description... -
Page 8: Required Tools
SRA-40 antenna with surface / pole mount Antenna Pole / Flush mount flange ‘O’ Ring Surface mount base Gasket Cable 7.62 m (25 ft) antenna cable Mounting screws (3) for SIRIUS antenna Documentation Installation manual, warranty card Required tools Screwdriver. Marking pencil, drill and drill bits 14 mm, 3 mm (9/16”, 7/64”), or other tools appropriate to your specific application may also be needed. -
Page 9: Installing The Antenna
Installing the antenna Select the mounting location Electromagnetic Interference Compass RADAR 1.2 m (4 ft) Min 0.5 m (20”) Min 1.8 m (6 ft) Min Radio or AIS Transmitter Do not cut or alter the antenna cable. Do not remove its connector. -
Page 10: Pedestal Mount
Pedestal mount Use mounting gasket 3 mm (7/64”) as a template for hole 14 mm (9/16”) locations. Drill pilot holes for mounting screws. Use 3mm (7/64th) drill bit. Drill 14 mm (9/16th hole for antenna cable. Secure base (C) and gasket (D) to the surface using 3 screws (E). -
Page 11: Surface Mount
Surface mount Mounting on surfaces up to 6 mm (1/4”) in thickness. 6mm (1/4” )max Antenna Lock washer and nut Antenna extension cable Mounting on surfaces 6 mm (1/4”) to 25 mm (1”) in thickness. 6mm (1/4” ) - 25 mm (1”) Antenna Extension shaft Lock washer and nut... -
Page 12: Installing The Weather Module
1.5 m (5 ft) Min Radio or AIS Transmitter WM-2 Description Navico WM-2 Weather module. Preferably mount on to a vertical surface with connectors facing down. Secure the module to the surface using the screws provided or other suitable fastener When mounted on a vertical surface. -
Page 13: Wiring The Wm-2 Weather Module
Network. Connect to the display system’s Ethernet network. Sirius satellite antenna connector. Power: Connect to 12 or 24 v DC. The WM-2 is pro- tected by an internal auto resetting fuse. Connect to a breaker or fuse to protect the cable... -
Page 14: Connect Power
WM-2 weather module The WM-2 has a voltage rating of 12 V DC or 24 V DC. (9 V DC - 32 V DC max range). The red wire should always be connected to (+) DC V using a fuse or thermal breaker (5 Amp) to protect the cable. - Page 15 The WM-2 weather module can be configured to turn on when the display is turned on. For NSE connect the Power Control wires. WM-2 Black Black Yellow Yellow Remote Power On Bus 12 - 24 V DC Simrad GB40 connect the Grey wire on the 12 pin utility cable...
-
Page 16: Audio Connection
Audio connection SIRIUS satellite radio can be accessed and controlled from certain Navico displays. The supplied audio cable is connected to an on board amplifier. WM-2 Description WM-2 Weather module Audio out cable (supplied) 7 pin to 2 x RCA male connectors. -
Page 17: Connecting To Your Display
Connecting to your display Simrad NSE8, NSE12 Description Simrad NSE8 or NSE12 Navico WM-2 Ethernet cables 5 pin yellow: Connect directly to one of the three Ethernet ports or to NEP —see below. NEP (Network expansion port) 5 port Ethernet switch alternative for larger or multi-display systems. -
Page 18: Enable Weather On Nse Display
Enable weather on NSE display MENU Enable audio if subscribed to service Check status of the SIRIUS service Activate your account see SIRIUS activation page 20. 18 | Connecting to your display... -
Page 19: Simrad Gb40
In order for GB40 to function properly, a software upgrade is needed, see your dealer for more information. Description Simrad GB40 NavComputer Navico WM-2 Weather module 8 Port Ethernet Linker Ethernet Adapter cable 5 pin yellow - RJ45 Ethernet cables RJ45 GB40 does not support Sirius Audio. -
Page 20: Sirius Activation
SIRIUS activation To use the WM-2 weather module. You must have a subscription to the SIRIUS weather / radio service. Individual weather and audio subscriptions are available. You can also purchase a subscription that includes both weather and audio. For more information visit www.sirius.com/marineweather... -
Page 21: Spare Parts
Spare parts Part No. Description 151-100006-01 WM-2 module box 000-00129-001 Power cable 000-10032-001 Audio cable Ethernet cables NSE: Part No. Description 000-0127-55 Adapter cable: Ethernet Yellow to RJ45 adap- tor 0.3m (1 ft) 000-0127-56 Adapter cable: Ethernet Yellow male to RJ45 female 2 m (6.5 ft) -
Page 22: Troubleshooting
Troubleshooting LED Information 22 | Troubleshooting... -
Page 23: Module Data Retention
Symptom Suggestion Allows overlays Attempt to display weather data over- but no data. lay on your unit. If the unit can ‘see’ the module (allows overlays) but does not yet display data, wait 5 minutes and check Precipitation overlay (updated every 5 minutes). -
Page 24: Specifications
Specifications Environmental Thermal Non-operating: -35°C to + 85° C Operating: -15°C to 55°C (5°F to 131°F) Humidity Non-operating: 66°C, 95%, humidity, 18 hours EMI/EMC FCC Part 15 Class B sub-part J Water ingress EN 60529: 1992 (IEC 529 1989): IPX6 Shock &... -
Page 25: Dimensions
Dimensions 204 mm (8.02”) 183 mm (7.20”) WM-2 Dimensions | 25...