Phottix Mitros Instruction Manual
Phottix mitros ttl flash for canon
Hide thumbs
Also See for Mitros:
- Instruction manual (147 pages) ,
- Instruction manual (14 pages) ,
- Instruction manual (134 pages)
Related Manuals for Phottix Mitros
Summary of Contents for Phottix Mitros
- Page 1 Phottix Mitros TTL Flash for Canon INSTRUCTION MANUAL BENUTZERHANDBUCH MANUEL D’UTILISATION MANUAL DE INSTRUCCIONES INSTRUKCJA OBSŁUGI ISTRUZIONI D’USO РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ 说明书 Simp...
- Page 2 For advanced features please read this manual and be familiar with your camera Back / Left Side manual and operations. The Phottix Mitros TTL Flash for Canon is designed to work with Canon DSLR 1. LCD Display cameras and features ETTL I/II, Manual, Multi modes as well as Wireless Master/ 2.
-
Page 3: Installing Batteries
3. Lock the flash in position by pushing the locking lever to the right until the lock engages with a click. The Phottix Mitros TTL Flash comes with an attachable diffuser that can be add- 4. To Unlock, press the locking release button on the locking lever and slide to ed to the front of the flash head when needed. - Page 4 Overheating Protection The Phottix Mitros contains an overheating protection circuit that will slow flash recycle time to avoid overheating-related damage. Approximately 20 full-power flashes in a short amount of time will trigger this protection. A [ Hot! ] Icon will appear when the overheating protection circuit is in operation.
-
Page 5: The Lcd Display
1/1 – 1/128 (1 – 199) Hz A B C The LCD display on the Phottix Mitros flash contains important information re- In ETTL mode: HSS/SCS, FEB, EV garding flash settings and functions. In M mode: HSS/SCS, Group, Power Level... -
Page 6: Modeling Flash
The Phottix Mitros will remember flash settings. Mode, power levels, etc. will be To save battery power the Phottix Mitros TTL Flash is equipped with Idle and retained in the flash if it is turned off and then back on. -
Page 7: Flash Modes
Please note: - By default: FEB will be cancelled after three photos are taken. FEB can be set The Phottix Mitros has three flash modes: ETTL, Manual (M) and Multi (Strobo- in the Custom Functions screen (see C.Fn-03 below). scopic). - Page 8 This is a rough guideline: You may need to increase or decrease the shutter speed to get the desired result. In Manual Mode the flash will fire at the power level you set. The Phottix Mitros TTL Flash can be adjusted from 1/1 (full power) to 1/128 – 8 stops of adjustments Multi Stroboscopic Mode Output Chart in 1/3rd stop increments.
-
Page 9: Wireless Settings
Master with Flash mode: The Master flash on the camera will fire when a The Phottix Mitros can also be triggered as an Optical Slave (OS). In OS mode photo is taken. - Page 10 ETTL Modes 3. Pressing the buttons will cycle between Master with flash, Master without flash, Slave, OS and Off modes. A+B+C All three groups fire at an average of the total calculated output. 4. Select Master with flash or Master without flash. A:BC Groups A and B can be set by Flash Ratio (see below).
-
Page 11: Custom Functions
Custom Functions The Phottix Mitros TTL Flash comes with a number of programmable custom 3. Press the buttons to change the function within the menu. functions. To edit these functions (below): 4. Press the button to exit the C.Fn menu. - Page 12 7-9m/22.96-29.52 ft., Flash Information Display Reception angle: ±40°(horizontal), ±30°(vertical) For technical support or firmware upgrade checking the Phottix Mitros infor- Controlled slave groups: 3 (A, B, and C) mation may be need. To display the hardware, software, icon library and serial...