Table of Contents
Advertisement
Quick Links
Tomcat i875P S5102
Tomcat i875P
Copyright © TYAN Computer Corporation, 2003-2004. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from TYAN Computer
Corp.
All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following.
TYAN, Tomcat, i875P and S5102 are trademarks of TYAN Computer Corporation.
Intel, Pentium 4, and combinations thereof are trademarks of Intel Corporation.
Promise is a trademark of Promise Technology, Inc.
Award, AwardBIOS are trademarks of Award Software Incorporated.
Microsoft and Windows are trademarks of Microsoft Corporation.
IBM, PC, AT and PS/2 are trademarks of IBM Corporation.
ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.
Winbond is a trademark of Winbond Electronics Corporation.
Analog Devices is a trademark of Analog Devices, Inc.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
Information contained in this document is furnished by TYAN Computer Corporation and has
been reviewed for accuracy and reliability prior to printing.
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN products including liability or warranties relating to fitness for a particular purpose or
merchantability.
TYAN retains the right to make changes to product descriptions and/or
specifications at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting
from errors or inaccuracies of information contained in this document.
///
Revision 1.01
TYAN assumes no liability
i
http://www.tyan.com
User's Manual
S5102
Advertisement
Table of Contents
Related Manuals for TYAN Tomcat i875P S5102
Summary of Contents for TYAN Tomcat i875P S5102
- Page 1 TYAN retains the right to make changes to product descriptions and/or specifications at any time, without notice. In no event will TYAN be held liable for any direct or indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting from errors or inaccuracies of information contained in this document.
-
Page 2: Table Of Contents
Tomcat i875P S5102 Table of Contents Table of Contents Before you begin… ......................... iv Chapter 1: Introduction......................1-1 1.1 – Congratulations!...................... 1-1 1.2 – Hardware Specifications ..................1-1 Chapter 2: Board Installation ....................2-1 2.1 – Board Image ......................2-2 2.2 –... - Page 3 Tomcat i875P S5102 Table of Contents Viewing Drive Assignments ..................4-12 Deleting An Array....................4-12 Rebuilding A Mirrored Array..................4-14 Chapter 5: Diagnostics ......................5-1 5.1 Beep Codes ....................... 5-1 5.2 Flash Utility......................... 5-1 Appendix I: Glossary ......................6-1 Appendix II: Post Error Code for BIOS ................6-7 Appendix III: SMDC Information ..................
-
Page 4: Before You Begin
1x 34-Pin floppy drive cable 1x Ultra-DMA-133/100/66/33 IDE cable 1x Ultra-DMA-133/100/66/33 IDE cable 1x Tomcat i875P S5102 User’s Manual 1x Tomcat i875P S5102 Quick Reference Guide 1x TYAN driver CD 1x I/O shield 1 x Promise FastTrak 378 RAID Driver Diskette... -
Page 5: Chapter 1: Introduction
Intelligent Platform Management Interface (IPMI) monitoring through a Server Management Daughter Card. The Tomcat i875P S5102 are ATX form factor, onboard Gigabit Ethernet port, Fast Ethernet port, Serial ATA, IDE RAID and an onboard ATI 8MB PCI RAGE XL VGA. - Page 6 • PnP, DNI 2.0, WFM 2.0 Power Management • Support BIOS Boot Specification v1.01 (BBS) • Supports Watchdog timer ready and Note: TYAN reserves the right to add support or discontinue support for any OS with or without notice. http://www.tyan.com...
-
Page 7: Chapter 2: Board Installation
(i.e. power supply case). For the safest conditions, TYAN recommends wearing a static safety wrist strap. (2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the board in any way. -
Page 8: Board Image
Chapter 2: Board Installation 2.1 – Board Image The following is an image of the Tomcat i875P S5102. The above photograph is purely representative. Due to engineering updates and new board revisions, certain components may change and or be repositioned. The picture above may or may not look exactly like the board you received. -
Page 9: Board Parts
Tomcat i875P S5102 Chapter 2: Board Installation 2.2 – Board Parts LAN2 LAN1 J2 (VGA) CN1 (COM1) USB1 KB-MO1 (Optional) Winbond Intel GbE LAN W83627HF KB(Bottom) (Optional) Mouse(Top) Chassis Intel COM2 USB (Bottom) GbE LAN LAN (Top) Intel 10/100 LAN... -
Page 10: Block Diagram
Tomcat i875P S5102 Chapter 2: Board Installation 2.3 – Block Diagram The following is a block diagram of the Tomcat i875P S5102. mPGA478 ICS-952607 VRD10.0 Processor Socket 800/533/400 MHz System Bus ® Intel 875P Chipset Syatem Memory DDR 400/333/266 Channel A... -
Page 11: Jumper Settings & Definitions
Tomcat i875P S5102 Chapter 2: Board Installation 2.4 – Jumper Settings & Definitions Jumper Function Ref. Page Clear CMOS Page 2-5 Jumper Example Jumper OFF – open (without jumper cap) Jumper ON – closed (with jumper cap) CMOS Reset (JP3) -
Page 12: Connector Description
Tomcat i875P S5102 Chapter 2: Board Installation 2.5 – Connector Description Connector Function Ref. Page Chassis fan connector Page 2-6 COM2 port Page 2-7 SMDC Connector Page 2-7 CPU fan connector Page 2-6 SMBus_0 Connector Page 2-8 Front panel connector... - Page 13 Mouse(Top) Chassis Intel COM2 USB (Bottom) GbE LAN LAN (Top) Compatible with Tyan M3289 (SMDC) Intel 10/100 LAN See Appendix III for details In Tyan SMDC PWR1 RAGE XL Intel 875P NB - FAN SDRAM CPU - FAN USB3 S5102...
- Page 14 Tomcat i875P S5102 Chapter 2: Board Installation SMBus_0 Connector (J7) LAN2 LAN1 J2 (VGA) CN1 (COM1) USB1 KB-MO1 (Optional) Intel Winbond GbE LAN Pin 1: SMBUS_DATA W83627HF KB(Bottom) (Optional) Mouse(Top) COM2 Chassis Intel USB (Bottom) GbE LAN LAN (Top) Pin 2: GND...
- Page 15 Tomcat i875P S5102 Chapter 2: Board Installation EFI1 Connector LAN2 LAN1 J2 (VGA) CN1 (COM1) USB1 KB-MO1 (Optional) Winbond Intel GbE LAN W83627HF KB(Bottom) (Optional) Mouse(Top) Chassis Intel COM2 USB (Bottom) GbE LAN LAN (Top) Intel 10/100 LAN PWR1 RAGE XL...
- Page 16 Tomcat i875P S5102 Chapter 2: Board Installation Serial ATA Connectors (SATA1 & SATA2 & SATA3 & SATA4) SATA1 / SATA2 (from ICH5): RAID function is NOT supported SATA3 / SATA4 (from Promise PDC20378 chip): RAID function is supported LAN2 LAN1...
- Page 17 Tomcat i875P S5102 Chapter 2: Board Installation Front panel LAN display headers (J16, J17 and J18)** LAN2 LAN1 J2 (VGA) CN1 (COM1) USB1 KB-MO1 (Optional) Winbond Intel GbE LAN W83627HF Pin 4: GND KB(Bottom) (Optional) Mouse(Top) COM2 Chassis Intel USB (Bottom)
-
Page 18: Mounting The Motherboard
TYAN recommends using metal studs with screws that will fasten the motherboard more securely in place. - Memory Type: The Tomcat i875P S5102 supports unbuffered ECC and non-ECC type memory modules. Registered Memory is NOT supported. Below is a chart detailing what the most common motherboard studs look like and how they should be installed it. - Page 19 Tomcat i875P S5102 Chapter 2: Board Installation TIP: Use metal studs if possible, as they hold the motherboard into place more securely than plastic standoffs. 2-13 http://www.tyan.com...
-
Page 20: Installing The Memory
The following diagram shows the types of RAM modules you may encounter depending on your board: DDR Unbuffered DDR Unbuffered ECC Here are a few key points to note before installing memory into your Tomcat i875P S5102: • 128MB, 256MB, 512MB and 1GB unbuffered ECC and non-ECC PC2100/PC2700/PC3200 DDR memory modules are supported •... -
Page 21: Memory Installation Procedure
Tomcat i875P S5102 Chapter 2: Board Installation • Supported System Bus Frequency and Memory Speed Combinations CPU FSB DDR DIMM Type Memory Frequency 800MHz PC3200, PC2700*, PC2100 400, 333*, 266 MHz 533MHz PC2700, PC2100 333, 266 MHz 400MHz PC2100 266 MHz * When using 800MHz CPU FSB, PC2700 DDR DIMMS may run only at 320MHz (not 333MHz) due to chipset limitations. -
Page 22: Installing The Processor And Heatsink
Tomcat i875P S5102 Chapter 2: Board Installation 2.9 – Installing the Processor and Heatsink Your Tomcat i875P S5102 supports the latest processor technologies from Intel. Check the following page on TYAN’s website for latest processor support: http://www.tyan.com The following diagrams will detail how to install your processor: The diagram is provided as a visual guide to help you install socket processors and may not be an exact representation of the processors you have. - Page 23 Tomcat i875P S5102 Chapter 2: Board Installation Heatsink Installation After you are done installing the processor, you should proceed to installing the heatsink. The heatsink will ensure that the processor does not overheat, and will continue to operate at maximum performance. An overheated processor is also dangerous to the long-term reliability of the motherboard.
-
Page 24: Attaching Drive Cables
Attaching IDE drive cabling is simple. These cables are “keyed” to only allow them to be connected in the correct manner. TYAN motherboards have two on-board IDE channels, each supporting two drives. The black connector designates the Primary channel, while the white connector designates the Secondary channel. - Page 25 Tomcat i875P S5102 Chapter 2: Board Installation Serial ATA Attaching Serial ATA cables to the Serial ATA connectors is illustrated below: Se rial ATA Hard drive Serial ATA Cable Serial ATA Connector Serial ATA Cable Power Cable Simply plug in the BLACK END of the Serial ATA cable into the motherboard Serial ATA connector, and the other end(s) into the drive(s).
-
Page 26: Installing Add-In Cards
Tomcat i875P S5102 Chapter 2: Board Installation Below are some symptoms of incorrectly installed floppy drives. While they are minor and installing them incorrectly doesn’t cause severe problems, it may cause your system to freeze or crash when trying to read and/or write to diskettes. -
Page 27: Connecting External Devices
Tomcat i875P S5102 Chapter 2: Board Installation 2.12 – Connecting External Devices Connecting external devices to the motherboard is an easy task. The standard devices you should expect to plug into the motherboard are keyboards, mice, and printer cables. The... - Page 28 Tomcat i875P S5102 Chapter 2: Board Installation 10/100/1000 Mbps LAN1 Link/Activity LED Scheme PCB Rev.: MOAA / MOAB use only Normal Left Right Left LED Right LED Left LED Right LED Link Yellow Blink Green 10 Mbps Active Blink Yellow...
-
Page 29: Installing The Power Supply
Tomcat i875P S5102 Chapter 2: Board Installation 2.13 – Installing the Power Supply There are two power connectors on this motherboard. By default, this motherboard requires that you have an ATX12V power supply that has the standard ATX-style 20-pin connector, as well as an additional 4-pin square connector. -
Page 30: Chapter 3: Bios Setup
Tomcat i875P S5102 Chapter 3: BIOS Setup Chapter 3: BIOS Setup Installation The BIOS is the basic input/output system, the firmware on the motherboard that enables your hardware to interface with your software. This chapter describes different settings for the BIOS that can be used to configure your system. -
Page 31: Main Bios Setup
Chipset section unless you are absolutely sure of the outcome. The Chipset defaults were carefully chosen by TYAN or your system manufacturer for the best performance and reliability. Even a seemingly small change to the Chipset setup options may cause the system to become unstable or unusable. - Page 32 Tomcat i875P S5102 Chapter 3: BIOS Setup Advanced BIOS Features Use this menu to set the Advanced Features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registers and optimize your system's performance.
-
Page 33: Standard Cmos Features
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.2 – Standard CMOS Features In this section, you can alter general features such as the date and time, as well as access to the IDE configuration options. Note that the options listed below are for options that can directly be changed within the Main Setup screen. -
Page 34: Advanced Bios Features
Tomcat i875P S5102 Chapter 3: BIOS Setup Video: Defines video display mode. EGA/VGA / CGA 40 / CGA 80 / MONO Halt On: Determines if the computer should stop when an error is detected during power up. No Errors / All Errors / All, But Keyboard / All, But Diskette / All, But Disk/Key 3.3 –... - Page 35 Tomcat i875P S5102 Chapter 3: BIOS Setup Boot Sequence: Select 〔Press Enter〕to set Boot Sequence Swap Floppy Drive: This will swap your physical drive letters A & B if you are using two floppy disks. Enabled / Disabled Boot Up Floppy Seek: During Power-On Self-Test (POST), BIOS will determine if the floppy disk drive installed is 40 or 80 tracks.
- Page 36 Tomcat i875P S5102 Chapter 3: BIOS Setup Small Logo (EPA) Show: Toggles the display of the EPA Energy Star logo at POST. Enabled / Disabled CPU Feature: Phoenix – AwardBIOS CMOS Setup Utility CPU Feature Delay Prior to Thermal [16 Min]...
- Page 37 Tomcat i875P S5102 Chapter 3: BIOS Setup Boot Sequence: Phoenix – AwardBIOS CMOS Setup Utility Boot Sequence ►Hard Disk Boot Priority [Press Enter] Item Help First Boot Device [Floppy] _________________________ Second Boot Device [Hard Disk] Third Boot Device [CDROM] Menu Level ►►...
-
Page 38: Advanced Chipsets Features
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.4 – Advanced Chipsets Features In Advanced Chipset Features, you will be abled to adjust many of the chipset special features. Phoenix – AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable... -
Page 39: Integrated Peripherals
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.5 – Integrated Peripherals Options related to onboard peripheral features can be altered through the following: Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals ► OnChip IDE Device [Press Enter] Item Help ► Onboard Device... - Page 40 Tomcat i875P S5102 Chapter 3: BIOS Setup On-Chip Primary PCI IDE: The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select “Enabled” to activate each channel separately. Enabled / Disabled Primary / Secondary Master/ Slave PIO: The four IDE PIO (Programmed Input / Output) field let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.
- Page 41 Tomcat i875P S5102 Chapter 3: BIOS Setup USB 2.0 Controller: This item allows you to decide to “Enable” or “Disable” the USB 2.0 device. Enabled / Disabled USB Keyboard Support: Select “Enabled” if your system contains a USB controller and you have a USB keyboard.
- Page 42 Tomcat i875P S5102 Chapter 3: BIOS Setup Onboard FDC Controller: Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install and-in FDC or the system has no floppy drive, select “Disabled”...
-
Page 43: Power Management Setup
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.6 – Power Management Setup Options related to power management can be altered through the following: Phoenix – AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function [Enabled] Item Help Power Management [User Define]... - Page 44 Tomcat i875P S5102 Chapter 3: BIOS Setup Suspend Mode: Defines the method used to power off the system. Disabled / Standby / Sleep HDD Power Down: Defines hard drive power down delay. Disabled / 1 minutes / 5 minutes / 10 minutes / 30 minutes / 45 minutes / 60 minutes CPU THRM-Throttling: Defines the duty cycle of THRM-Throttling.
- Page 45 Tomcat i875P S5102 Chapter 3: BIOS Setup USB KB WakeUp From S3 (S4) This item allows you to “Enable” or “Disable” USB KB WakeUp from S3 (S4) function. Disabled / Enabled Resume by Alarm: Defines the time/date when the system will wake up.
-
Page 46: Pnp/Pci Configurations
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.7 – PnP/PCI Configurations Options related to all the configurations of PnP / PCI resources. Phoenix – AwardBIOS CMOS Setup Utility PnP / PCI Configurations Reset Configuration Data [Disabled] Item Help _________________________ Resources Controlled By... -
Page 47: Pc Health Status
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.8 – PC Health Status 3.8.1 This menu is related to detecting system temperature, voltage, fan and speed. (PCB Rev.: 03MOA, 03MOAA and 03MOAB use only) Phoenix – AwardBIOS CMOS Setup Utility PC Health Status Current CPU Temp. - Page 48 Tomcat i875P S5102 Chapter 3: BIOS Setup 3.8.2 This menu is related to detecting system temperature, voltage, fan and speed. Phoenix – AwardBIOS CMOS Setup Utility PC Health Status Auto FAN1~4 Power Control [Disable] Current CPU Temperature Item Help xx℃/xxx℉...
-
Page 49: Frequency/Voltage Control
↑↓←→: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults CPU Clock Ratio: Sets the CPU multiplier. TYAN does not recommend changing this setting from the default setting. 16X…22X / Auto / Default Auto Detect DIMM / PCI Clk: Sets the BIOS to automatically adjust PCI and memory bus speeds accordingly. -
Page 50: Load Fail-Safe Defaults
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.10 – Load Fail-Safe Defaults Phoenix – AwardBIOS CMOS Setup Utility ► Standard CMOS Features ► Frequency/Voltage Control ► Advanced BIOS Features Load Fail-Safe Defaults ► Advanced Chipset Features Load Optimized Defaults ► Integrated Peripherals Set Supervisor Password ►... -
Page 51: Supervisor/User Password Setting
Tomcat i875P S5102 Chapter 3: BIOS Setup 3.12 – Supervisor/User Password Setting Phoenix – AwardBIOS CMOS Setup Utility ► Standard CMOS Features ► Frequency/Voltage Control ► Advanced BIOS Features Load Fail-Safe Defaults ► Advanced Chipset Features Load Optimized Defaults ► Integrated Peripherals Set Supervisor Password ►... -
Page 52: Exit Selecting
Tomcat i875P S5102 Chapter 3: BIOS Setup To disable a password, just press <Enter> when you are prompted to enter the password. A message will confirm the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely. - Page 53 Tomcat i875P S5102 Chapter 3: BIOS Setup Exit Without Saving Phoenix – AwardBIOS CMOS Setup Utility ► Standard CMOS Features ► Frequency/Voltage Control ► Advanced BIOS Features Load Fail-Safe Defaults ► Advanced Chipset Features Load Optimized Defaults ► Integrated Peripherals Set Supervisor Password ►...
-
Page 54: Chapter 4: Sata/Raid Setup (For Sata Raid Model)
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Chapter 4: SATA/RAID Setup (for SATA RAID model) ® The motherboard includes the Promise PDC20378 SATA RAID controller with two Serial ATA interfaces and one Parallel ATA133 interface to support RAID 0, 1 or 0+1 configuration Note: The PDC20378 only supports HDD devices. -
Page 55: Creating Your Disk Array
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) 4.2 - Creating Your Disk Array WARNING: Before installing the driver into an existing system, backup any necessary data. Failure to follow this accepted PC practice could result in data loss. - Page 56 Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Press “1” to display the Auto Setup Menu below. This is the fastest and easiest method to creating your first array. FastBuild (tm) Utility 2.xx (c) 2002-2005 Promise Technology, Inc.
-
Page 57: Creating An Array For Performance
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Creating an Array for Performance NOTE: The PDC20378 enables you to create striped arrays with 1, 2, 3 or 4 drives. To create an array for best performance, follow these steps: Using the Spacebar, choose “Performance”... -
Page 58: Creating A Security Array With An Existing Data Drive
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Creating a Security Array with an Existing Data Drive Follow these steps: Using the Spacebar, choose “Security” under the Optimize Array for section. Press <Ctrl-Y> keys to save your selection. The window below will appear. -
Page 59: Installing Software Drivers
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) 4.3 - Installing Software Drivers New Windows 2000/XP Installation The following details the installation of the PDC20378 drivers while installing Windows 2000/XP. Start the installation: • Floppy Install: Boot the computer with the Windows 2000/XP installation diskettes. -
Page 60: New Windows 98/Me Installation
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) New Windows 98/Me Installation After configuring the PDC20378 controller and the attached hard drive(s), partition and format your hard drive(s), if necessary. Install Windows 98/Me normally. After installation, go the “Start” menu and choose “Settings.”... -
Page 61: New Windows Nt 4.0 Installation
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) New Windows NT 4.0 Installation Start the system installation by booting from the Windows NT disk: Floppy install: boot the system with the Windows NT installation diskettes. Floppyless install: boot from floppy and type “WINNT /B”. After files have been copied, the system will reboot. -
Page 62: Using Fastbuild™ Configuration Utility
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) 4.4 - Using FastBuild™ Configuration Utility The FastBuild™ Configuration Utility offers several menu choices to create and manage the drive array on the Promise PDC20378. For purposes of this manual, it is assumed you have already created an array in the previous chapter and now wish to make a change to the array or view other options. -
Page 63: Navigating The Fastbuild™ Setup Menu
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Navigating the FastBuild™ Setup Menu When using the menus, these are some of the basic navigation tips: Arrow keys highlights through choices; [Space] allows cycle through options; [Enter] key selects an option; [ESC] key is used to abort or exit the current menu. -
Page 64: Creating Arrays Automatically
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Creating Arrays Automatically The Auto Setup <1> selection from the Main Menu can intuitively help create your disk array. It will assign all available drives appropriate for the disk array you are creating. After making all selections, use Ctrl-Y to Save selections. -
Page 65: Viewing Drive Assignments
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Viewing Drive Assignments The View Drive Assignments <2> option in the Main Menu displays whether drives are assigned to a disk arrays or are unassigned. The menu also displays the data transfer mode that relates to speed used by each drive (U6 refers to 133MB/sec transfers, U5 refers to 100MB/sec transfers, U4 refers to 66MB/sec transfers, etc...) - Page 66 Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) To delete an array, highlight the Array you wish to delete and press the [Del] key. The View Array Definition menu will appear (see below) showing which drives are assigned to this array.
-
Page 67: Rebuilding A Mirrored Array
Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) Rebuilding A Mirrored Array The Rebuild Array <5> Menu option is necessary to recover from an error in a mirrored disk array. You will receive an error message when booting your system. - Page 68 Tomcat i875P S5102 Chapter 4: SATA/RAID Setup (for SATA RAID model) FastBuild (tm) Utility 2.xx (c) 2002-2005 Promise Technology, Inc. [ Rebuild Array Menu ] Array No RAID Mode Total Drv Status Array 2 Mirror Critical Stripe Block: Not Available...
-
Page 69: Chapter 5: Diagnostics
BIOS. There are no exceptions. TYAN does not have a policy for replacing BIOS chips directly with end users. In no event will TYAN be held responsible for damages done by the end user. -
Page 70: Appendix I: Glossary
Tomcat i875P S5102 Appendix I: Glossary Appendix I: Glossary ACPI (Advanced Configuration and Power Interface): a power management specification that allows the operating system to control the amount of power distributed to the computer’s devices. Devices not in use can be turned off, reducing unnecessary power expenditure. - Page 71 EEPROM (Electrically Erasable Programmable ROM): also called Flash BIOS, is a ROM chip which can, unlike normal ROM, be updated. This allows you to keep up with changes in the BIOS programs without having to buy a new chip. TYAN’s BIOS updates can be found at http://www.tyan.com...
- Page 72 Form factor: an industry term for the size, shape, power supply type, and external connector type of the Personal Computer Board (PCB) or motherboard. The standard form factors are the AT and ATX, although TYAN also makes some Baby-AT and ATX Footprint boards. Global timer: onboard hardware timer, such as the Real-Time Clock (RTC).
- Page 73 Tomcat i875P S5102 Appendix I: Glossary Latency: the amount of time that one part of a system spends waiting for another part to catch up. This is most common when the system sends data out to a peripheral device, and it waiting for the peripheral to send some data back (peripherals tend to be slower than onboard system components).
- Page 74 Tomcat i875P S5102 Appendix I: Glossary RAID (Redundant Array of Independent Disks): a way for the same data to be stored in different places on many hard drives. By using this method, the data is stored redundantly, also the multiple hard drives will appear as a single drive to the operating system. RAID level 0 is known as striping, where data is striped (or overlapped) across multiple hard drives, but offers no fault-tolerance.
- Page 75 Tomcat i875P S5102 Appendix I: Glossary SSI (Server System Infrastructure): an industry initiative intended to provide ready-to-use design specifications for common server hardware elements (chassis, power supplies, and racks) to promote and support server industry growth. Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally.
-
Page 76: Appendix Ii: Post Error Code For Bios
Tomcat i875P S5102 Appendix II: Post Error Code for BIOS Appendix II: Post Error Code for BIOS POST (hex) Description CFh: Test CMOS R/W functionality. C0h: Early chipset initialization: -Disable shadow RAM -Disable L2 cache (socket 7 or below) -Program basic chipset registers... - Page 77 Tomcat i875P S5102 Appendix II: Post Error Code for BIOS POST (hex) Description 18h: Detect CPU information including brand, SMI type (Cyrix or Intel) and CPU level (586 or 686). 1Bh: Initial interrupts vector table. If no special specified, all H/W interrupts are directed to SPURIOUS_INT_HDLR &...
- Page 78 Tomcat i875P S5102 Appendix II: Post Error Code for BIOS POST (hex) Description 37h: Test DMA Channel 1. 39h: Test DMA page registers. 3Ch: Test 8254 3Eh: Test 8259 interrupt mask bits for channel 1. 40h: Test 8259 interrupt mask bits for channel 2.
- Page 79 Tomcat i875P S5102 Appendix II: Post Error Code for BIOS POST (hex) Description 67h: Prepare memory size information for function call: INT 15h ax=E820h 69h: Turn on L2 cache 6Bh: Program chipset registers according to items described in Setup & Auto- configuration table.
- Page 80 Tomcat i875P S5102 Appendix II: Post Error Code for BIOS E8POST.ASM starts Description 82h: 1. Call chipset power management hook. 2. Recover the text fond used by EPA logo (not for full screen logo) 3. If password is set, ask for password.
-
Page 81: Appendix Iii: Smdc Information
Tyan SMDC is not a peripheral card. Unlike regular peripheral card such as AGP card, Network card or SCSI card, SMDC does not require any hardware specific driver. As long as a standby power comes into the system, SMDC will begin looking after the system. -
Page 82: Technical Support
Help Resources: 1. See the beep codes section of this manual. 2. See the TYAN website for FAQ’s, bulletins, driver updates, and other information: http://www.tyan.com 3. Contact your dealer for help BEFORE calling TYAN. 4. Check the TYAN user group: alt.comp.periphs.mainboard.TYAN... - Page 83 Tomcat i875P S5102 User’s Manual Notice for the USA Compliance Information Statement (Declaration Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation.