Advertisement
Quick Links
Advertisement
Related Manuals for JOVY Systems iSolder-40
Summary of Contents for JOVY Systems iSolder-40
- Page 1 ® JOVY SYSTEMS iSolder-40 User Manual Rev. 1.00...
- Page 2 Thank you for purchasing Jovy systems Solder-40 soldering station. Please read this manual before operating the Solder-40. Keep the manual in accessible place for future reference User Manual...
-
Page 3: Table Of Contents
Index Warnings and precautions ---------------------- Specification ---------------------------------------- Initial setup ----------------------------------------- Operating modes guideline---------------------- Tip care and selection ---------------------------- Hints and Tricks ------------------------------------ Warranty---------------------------------------------... -
Page 4: Warnings And Precautions
(Do not use it with wood, wax, plastic, etc…) Use only tips and parts supplied by JOVY Systems®. Make sure that the tip does not touch any object while in operating mode. It negatively affects the tip sensitivity. -
Page 5: Specification
188 x 144 x 120 Power chord length (Plug type) 1.8 meters Hand piece technical specifications: Tip-to-Ground Potential < 2 mV Tip-to-Ground Resistance < 2 Ohm Hand piece cord Length 1.5 meters Hand piece Length 158 mm iSolder-40 is ESD Safe Equipment... -
Page 6: Initial Setup
Initial set-up Packing list: Item Code Quantity Solder Station JV-SSS Main tip JV-ST1 Hand piece holder JV-SS2 Cleaning sponge JV-SS3 Protective Pad JV-SS6 Power cord JV-SS7 JV-SSS JV-ST1 JV-SS2 JV-SS6... - Page 7 (110VAC/60Hz or 220VAC/50Hz). 2- Place and arrange the iSolder-40 with all other parts in a convenient location in your workspace. 3- Insert the desired tip into the hand piece to end – fastening click heard – by using the protective pad, steps as shown in figure 1 and 2.
- Page 8 4- Plug the power cord into electricity supply and switch on the iSolder-40. 5- If the tip is inserted correctly a green led indicator will start flashing – Heating up mode. If the tip inserted wrongly the led color will be red.
-
Page 9: Operating Modes Guideline
When the controller is active and sensing, the fast flashing Green Led will be seen from time to time. 1)Heating up mode When the tip is fully inserted into the hand piece, the iSolder-40 controller starts to detect the tip. The indicator of this state is a flashing green led. - Page 10 3)Sleep mode When the iSolder-40 controller senses no usage for 5 minutes, the iSolder-40 starts the sleep mode for saving power. The indicator of this mode is a flashing red led (short on; short off) To get out from sleep mode and turn to operating mode, move the hand piece from the holder and wait until the iControl automatically senses and update the status from Sleep to Operating mode.
-
Page 11: Tip Care And Selection
Tip care and selection Available tips for Solder-40 JV-TP1 JV-TP2 JV-TP3 JV-TP4 JV-TP5 JV-TP6... - Page 12 Guide for tip selection: Good Too light Too heavy The ideal tip choice is the tip which its active area should cover completely the solder area. The best percentage of soldering area to tip active area is 2:1. Tip care guide for longer life time: - Clean the tip by wiping it with a wet sponge and slightly drag it out after each use.
-
Page 13: Hints And Tricks
Hints and Tricks Tip oxidation removal: Firstly, clean the tip using a wet sponge then clean with wire brush. Secondly, use a tip re-activator chemical to remove hard residues and oxidation, and finally re- tinning using solder wire (flux cored). ... - Page 14 Sample applications for the Solder-40 main tip Any type of soldering material Heavy junctions...
-
Page 15: Warranty
Warranty Please visit Jovy systems web page (www.Jovy-systems.com/contact) on support form tab, fill in subject with product registration and make sure you write the iSolder-40 serial number. You may also contact the local representative or distributor for Jovy systems® for pricing and availability.