BT Duet 600 User Manual

At a glance

Hook switch
Lets you make a
follow-on call without
replacing the handset.
Speaker volume
control buttons
Used to adjust the
speaker volume
of a call.
M2
1 2 3
Quickdial button
Use to store and dial
4 5 6
Quickdial numbers.
8 9
7
Secrecy
0
(Program) button
Ringer
Allows you to talk Quickdial Recall
to someone in the Secrecy Redial
Pause
same room without
Program
your caller hearing.
Setting Up
Please read the instructions carefully before use, and keep this
user guide for future reference.
Connect the telephone line cord

Safety information

Do not expose to direct sunlight.
Do not stand your product on carpets or other surfaces which
generate fibres, or place it in locations preventing free flow of air
over its surfaces.
Do not submerge any part of your product in water and do not
use it in damp or humid conditions, such as bathrooms.
Do not expose your product to fire, explosive or other hazardous
conditions.
Using your Duet 600
telephone
To make a call
•Lift the handset. You will hear a dial tone.
•Enter the telephone number. The number will be shown on the
display and dialled.
To end a call
•Replace the handset.
Call Timer
Your Duet 600 automatically times the duration of all outgoing
and incoming calls. The call timer is shown on the right of the
LCD Display
display, replacing any number that was there, e.g.
Shows stored/
dialled telephone
To redial the last number
numbers. Also
displays call timer
Redial
and other visible
•The last number dialled is stored in the redial memory.
information
•Press the REDIAL button. The number is shown on the display
and dialled automatically.
Memory buttons
Use to store and
dial one-touch If you are redialling a number when connected to a switchboard,
numbers. wait until you hear a dial tone, then press the 9 button, wait again
for a dial tone and then press REDIAL. This applies even if 9 is
Recall button stored in REDIAL.
For use with
switchboards and
To switch secrecy on and off
BT Select Services.
When on a call you can talk to someone in the same room,
without your caller hearing.
Redial button
Press to redial the
Secrecy
last number called
•During a call press the SECRECY (Program) button.
or to enter a pause
The LED will flash to indicate that secrecy is on. You can talk
in the memory.
and your caller will not hear you.
•To resume your call press the SECRECY (Program) button
again. The LED will stop flashing.
To adjust the speaker volume
The speaker volume can only be adjusted when the telephone is
off the base.
The switch can be found on the left hand side of the telephone.
There are 5 levels. 1 = quietest. 5 = loudest.
The volume will remain at the level you have set between calls
until you adjust it again.
Press to increase the volume.
Press to decrease the volume.
The display will show the volume increase or decrease.
To adjust the ringer tone and volume
The Duet 600 has 3 ringer tones to choose from at 3 different
volume levels. One button sets both the tone and volume setting.
See the table opposite to help you select the right setting.
Secrecy
•Press the SECRECY (Program) button. The LED will start to flash.
•Press the #
•Press the keypad button, 0 to 9, for the tone/volume you want.
The display will show the current setting and you will hear a
beep from the handset which is not audible unless held up to
the ear, e.g. Press 5 = Tone 2 at medium volume (see table).
Display shows
•Press the SECRECY (Program) button. The LED will stop
flashing. Your selected setting is now stored.
00-14
TIMER.
up
down
0 - 9
Secrecy
(Ringer) button.
RINGER TONE VOLUME
2 2
Vol.1 Vol. 2
Tone Quiet Medium
1 2
Tone 1
Tone 2 4 5
7 8
Tone 3
No Tone 0 = Silent
(the display will show Ringer Off to confirm setting)
When the ringer is switched off the ring indicator light will continue
to flash to indicate an incoming call. The ringer will remain
switched off until you lift the handset again. It is not possible to
switch the ringer off permanently.
To use the Recall button
Recall
You may need to use the RECALL button if you are connected
to a switchboard/PBX (Private Branch Exchange), contact your
PBX supplier for further information. The RECALL button is
also used for BT Select Services.
Storing and dialling numbers
M1 M2 M3
You can store up to 10 numbers in the QUICKDIAL memory
(0 to 9) and a further 3 numbers using the MEMORY buttons
(M1, M2 and M3).
Your Duet 600 comes with memory labels which can be used
to keep a note of your stored numbers.
To store a number using the MEMORY buttons
(M1, M2, M3)
Secrecy M1 M2 M3 Secrecy
•Press the SECRECY (Program) button. The LED will start
to flash.
•Press the MEMORY button (M1, M2, or M3) under which you
want to store the number. The display will show the location
you have chosen, e.g.
MEMORY
1
.
•Use the keypad to enter the telephone number.
•You can use the UP/DOWN button on the side of the telephone
to go back and delete if you have entered the wrong number.
•Press the SECRECY (Program) button. The number will stop
flashing and is now stored.
The display will show
MEMORY
1 Stored.
To store a pause in the dialling sequence of a memory number,
e.g 9, pause, 6, press the REDIAL button.
Vol. 3
Loud
3
6
9