General; Getting Started; Using Your Monitor; Preset And User Modes - Sony CPD-200ES Service Manual

The operating instructions mentioned here are partial abstracts from the Operating Instruction
Manual. The page numbers of the Operating Instruction Manual remain as in the manual.

Getting Started

Before using this monitor, please make sure that the following
items are included in your package: Multiscan 100 ES /200
monitor (1), power cord (1), warranty card (1), "Windows95
Monitor Information Disk" (1), and this operating instruction
manual (1).
This monitor will sync with any IBM or compatible system
equipped with VGA or greater graphics capability. Although
this monitor will sync to other platforms running at horizontal
frequencies between 30 and 70 kHz, including Macintosh and
Power Macintosh system, a cable adapter is required. Please
consult your dealer for advice on which adapter is suitable for
your needs.
Step 1: With the computer switched off, attach the video
signal cable to the video output.
IBM or compatible
computer
to video output
Apple computer
to video output
Macintosh adapter (not supplied)
Step 2:
Attach the power cord to the monitor and the other
end to a power outlet.
Power cord (supplied)
to a power outlet
Step 3: Turn on the monitor and computer.
Step 4: If necessary, adjust the user controls according to
your personal preference.
The installation of your Multiscan 100 ES /200 ES is complete.
Enjoy your monitor.
1) VGA is a trademark of IBM Corporation.
2) VESA is a trademark of the non-profit organization, Video
Electronics Standard Association.
3) Macintosh is a trademark of Apple Computer Inc.
4) Windows ® is a registered trademark of Microsoft
Corporation in the United States and other countries.
4

Using Your Monitor

Preset and User Modes

ES
ES ES
The Multiscan 100 /200 has factory preset modes for the 8 most
popular industry standards for true "plug and play" capability.
For less common modes, the Multiscan 100ES/200ES's Digital
Multiscan Technology will perform all of the complex adjustments
necessary to ensure a high quality picture for any timing between
30 and 70 kHz.
CPD-100ES/100EST and CPD-200ES/200EST
No. Resolution Horizontal Vertical
Graphics
(dots × lines)
Frequency
Frequency Mode
640 × 480
1 31.5 kHz 60 Hz VGA Graphic
640 × 480
2 43.3 kHz 85 Hz VESA
800 × 600
3 46.9 kHz 75 Hz VESA
800 × 600
4 53.7 kHz 85 Hz VESA
832 × 624
5 49.7 kHz 75 Hz Macintosh
16
1024 × 768
6 60.0 kHz 75 Hz
VESA
1024 × 768
7
68.7 kHz 85 Hz VESA
1280 × 1024
8 64.0 kHz 60 Hz VESA
®4)
For the customers using the Windows
I
nstall the new model information of the Sony computer display
from "Windows95 Monitor Information Disk" into your PC. (To
install the file, refer to the attached "About the Windows95 Monitor
Information Disk/File".)
This monitor complies with "VESA DDC", the standards of
Plug&Play. If your PC/graphic board complies with DDC,
select "Plug and Play Monitor (VESA DDC)" or this
monitor's model name (CPD-100ES/100EST or CPD-200ES/
200EST) as "Monitor type" from "Control Panel" on
Windows95. Some PC/graphic boards do not comply with
DDC. Even if they comply with DDC, they may have some
problems on connecting to this monitor. In this case, select
this monitor's model name (CPD-100ES/100EST or CPD-
200ES/200EST) as "Monitor type" on Windows95.
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 µsec.
Horizontal blanking width should be: >3.6 µsec. (Multiscan 100
>3.0 µsec. (Multiscan 200
Vertical sync width should be: < 560 µsec.
Note
CPD-100ES/100EST and CPD-200ES/200EST does not apply to
"
Macintosh 21 color mode.
SECTION 1

GENERAL

Adjustments
When one of the preset-type signals is input, no picture
adjustment is necessary.
You can, however, adjust the picture to your preferences by
following the procedure described below.
You can adjust all items on the OSD (On Screen Display).
Control Panel
RESET COLOR

Adjusting the Picture Contrast

1)
2)
The adjustment data becomes the common setting for all input
2)
signals.
2)
1
Press the > ?// button.
Color 2)
"
The "BRIGHTNESS/CONTRAST" OSD appears.
2)
2)
2)
95
2
Press the > ?// buttons to adjust picture contrast.
/ . . . for more contrast
? . . . for less contrast
The "BRIGHTNESS/CONTRAST" OSD disappears 3 seconds
after you release the buttons.
To reset, press the RESET button while the OSD is on.

Adjusting the Picture Brightness

The adjustment data becomes the common setting for all input
ES )/
signals.
ES
).
1
Press the ¨ >/. button.
The "BRIGHTNESS/CONTRAST" OSD appears.
2
Press the buttons to adjust picture brightness.
¨ >/.
. . . . for less brightness
> . . . for more brightness
The "BRIGHTNESS/CONTRAST" OSD disappears 3 seconds
after you release the buttons.
To reset, press the RESET button while the OSD is on.
p Before adjusting the items, turn on the unit and feed the
video signal from the connected computer/work station.
p Adjustments will be stored automatically.
GEOM SIZE CENTER

Adjusting the Picture Centering

The adjustment data becomes the individual setting for each
input signal received.
1
Press the CENTER button.
The "CENTER" OSD appears.
CENTER
BRIGHTNESS/CONTRAST
1 0 0 50
3 1 . 5 kHz/70Hz
2
For vertical adjustment
Press the ¨ >/. buttons.
Horizontal Vertical
frequency∗ frequency∗
> . . . to move up
. . . . to move down
For horizontal adjustment
>
Press the ?// buttons.
? . . . to move left
/ . . . to move right
BRIGHTNESS/CONTRAST
To erase the "CENTER" OSD, press the CENTER button
again.
The "CENTER" OSD automatically disappears 10 seconds after
1 0 0 50
you release the buttons.
3 1 . 5 kHz/70Hz
To reset, press the RESET button while the OSD is on.
Horizontal Vertical
frequency∗ frequency∗
∗ The horizontal and vertical frequencies for each input signal
received appear on the "BRIGHTNESS/CONTRAST" OSD.
CENTER
3 2 68
5