Advertisement
Quick Links
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS
United States
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED
INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
flammable vapors and liquids in the vicinity of this or any other appliance.
1. Clearances and Dimensions
a. Provide adequate clearances between the range and adjacent combustible surfaces.
b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor.
c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface
must be solid and level.
FRONT
TYPICAL CABINET INSTALLATION
VIEW
* 30" minimum clearance between the top of the cooking surface
and the bottom of an unprotected wood or metal cabinet; or 24
" minimum when bottom of wood or metal cabinet is protected
by not less than ¼" flame retardant millboard covered with not
less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024"
aluminum or 0.020" copper. The minimum clearance is 0" for the
rear of the range. Follow all dimension requirements provided
above to prevent property damage, potential fire hazard, and
incorrect countertop and cabinet cuts.
Avoid locating cabinet storage space above the surface units to
eliminate the possibility of cabinets catching on fire, or personal
burns from reaching for the cabinets over the heated units. If
cabinet storage is to be provided, risk can be reduced by installing
a range hood that projects horizontally a minimum of 5" beyond
the bottom of the cabinets.
Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the appliance.
2. Remove all packing material before connecting the electrical
supply to the appliance.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Printed in Canada
FOR YOUR SAFETY: Do not store or use gasoline or other
SIDE
VIEW
1
FRONT
29-7/8"
VIEW
49"
Maximum
42"
Door open
All dimensions for
electrical outlet location are
maximum.
Cubed area shows
where the electrical
Terminal
outlet must be installed
Block
for the range to be
Location
flush to the wall.
Important Note to the Consumer
Keep these instructions with your Use and
Care Guide for future reference.
Canada
25-3/4"
36 1/8"
30"
BACK
VIEW
Wall
Edge
318201728 (1103) Rev. A
Advertisement
Related Manuals for Sears 30"
Summary of Contents for Sears 30"
-
Page 1: Clearances And Dimensions
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS United States Canada INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. -
Page 2: Anti-Tip Bracket Installation Instructions Important Safety Warning
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS 2. Tools You Will Need B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot hole where screws are to be located. If bracket For leveling legs and Anti-Tip Bracket: is to be mounted to the wall, drill pilot hole at an • Adjustable wrench or channel lock pliers • 5/16" Nutdriver or Flat Head Screwdriver approximate 20°... -
Page 3: Serial Plate Information
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS 4. Serial Plate Information C. Level and position the range - Slide range to its final position. Insert the range leveling leg in the anti- The serial plate is located as tip bracket. Visually verify if the anti-tip bracket is shown. -
Page 4: Electrical Shock Hazard
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS 5. Electrical Connection Requirements The user is responsible for connecting the power supply cord to the connection block located behind This appliance must be properly installed and the back panel access cover. grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA This appliance may be connected by means of No. 70-latest edition- and local electrical code permanent "hard wiring"; flexible armored or requirements. -
Page 5: Three Conductor Wire Connection To Range
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS Four Conductor Wire Connection to Range This appliance is manufactured Where local codes does NOT permit connection of with the frame grounded by connection of a the frame grounding conductor to the neutral wire grounding strap between the neutral power of the copper power supply cord (see Figure 9): supply terminal and the frame. If used in USA, 1. -
Page 6: Checking Operation
3-Wire (Grounded Neutral) Electrical System Guide. It may save you time and expense. The (Example: Junction Box) list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Refer to your Use and Care Guide for Sears service phone numbers, or call 1-800-4-MY-HOME ®...