4000 audio, picture and video 0.7 Vp-p (75 Ω) output level: contents and 400 groups 0.7 Vp-p (75 Ω) output level: lData recorded with Panasonic SD multi cameras or DVD Terminal: Pin jack (Y: green, P : blue, video recorders. : red) (1 system)
SA-HT885WGC / SA-HT885WGS 1. Specifications are subject to change without notice. Mass and dimensions are approximate. 2. Total harmonic distortion is measured by the digital spectrum analyzer. Solder: This model uses lead free solder (PbF). CONTENTS Page Page 1 Use of Active Subwoofer 12 Disassembly and Main Component Replacement Procedure 1.1.
Page 4
SA-HT885WGC / SA-HT885WGS 14 Optical Pick-up Self-Diagnosis and Replacement Procedure 18 Abbreviations 19 Voltage Chart 14.1. Optical Pickup Breakdown Diagnosis 19.1. DVD Module P.C.B. 14.2. Service Mode Table 1 19.2. Main P.C.B. 14.3. DVD Self Diagnostic Function-Error Code 19.3. FL P.C.B. & MIC P.C.B & Tray Loading P.C.B.
SA-HT885WGC / SA-HT885WGS 1 Use of Active Subwoofer 1.1. Checking Player when Active Subwoofer is not used 1. This unit uses the active subwoofer to supply the power of the component, and the active subwoofer should be connected to the component to check operational conditions of the component.
SA-HT885WGC / SA-HT885WGS 2 Safety Precautions 2.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
SA-HT885WGC / SA-HT885WGS Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
SA-HT885WGC / SA-HT885WGS 6 Precaution of Laser Diode CAUTION : This product utilizers a class 1 laser. Invisible laser radiation is emitted from the optical pick up lens. When the unit is turned on: Wavelength : 658nm/780nm Maximum output radiation power from pick up : 100µW/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1.
SA-HT885WGC / SA-HT885WGS 8 General Description 8.1. Operating instructions /AV SYSTEM AV SYSTEM TUNER/BAND, TV/AV TUNER/BAND DVD/CD TV/AV DVD/CD NUMBERED BUTTONS VOLUME -/-- VOLUME CANCEL S 10 CANCEL SKIP SLOW/SEARCH (SKIP) (SLOW/SEARCH) (PLAY) (STOP) (PAUSE) TOP MENU MENU TOP MENU...
Recorded with devices using Version 1.1 of the Video Recording Format (a unified video recording standard), such as DVD video recorders, DVD video cameras, personal computers, etc. Recorded with Panasonic SD multi cameras or DVD video recorders using the DCF (Design rule for Camera JPEG File system) Standard Version 1.0.
SA-HT885WGC / SA-HT885WGS 8.3. Using of Receiver Unit (SH-FX50) · This model can be equipped with the digital transmitter and receiver to enjoy surround sound wirelessly.. 8.3.1. Below is tips on using the digital receiver...
SA-HT885WGC / SA-HT885WGS 8.3.2. Tips of using digital transmitter 8.4. About HighMAT 8.4.1. What’s HighMAT? Consumers worldwide are using PCs to create their own collections of music, photos and even video by burning them onto CDs. But how these collections can be experienced across different devices can be confusing to navigate, time consuming to access for a DVD player, and be incomplete in terms of music information available to the customer.
Page 14
SA-HT885WGC / SA-HT885WGS 8.4.2. Why take advantage of HighMAT? A Problem Defined:Today, when consumers create their own digital audio, video or photo collections on CD-R or other physical formats, there are numerous, inconsistent ways that devices read the data. For the consumer, the playback experience can be...
SA-HT885WGC / SA-HT885WGS 8.4.3. Benefits of HighMAT? Conventional HighMAT Even though DVD player is CD-R/RW compatible, the inconsistent ways HighMAT compatible products play content back with consistent that various DVD players can read the music or photos files often leads interface.
Page 16
SA-HT885WGC / SA-HT885WGS HighMAT is now available for CD Burning and in Leading DVD Players HighMAT is a new technology that is now available in leading software and consumer electronic devices to dramatically improve the digital media experience when you create homemade CDs HighMAT delivers a simple, standardized way for PC software and consumer electronics devices to talk to each other and work better together.
Page 17
SA-HT885WGC / SA-HT885WGS When you create your homemade CDs with software that supports HighMAT CD burning, and then play them back on a DVD player that supports HighMAT, you get better, easier navigation. You get folders you can access with a single click of your DVD player´s remote control.
SA-HT885WGC / SA-HT885WGS 9 Accessories AC cord Remote control AC cord (For GS area) AM loop antenna FM indoor antenna System cable Video Cable Speaker label Speaker cable...
SA-HT885WGC / SA-HT885WGS 11 Handling Precautions for Optical Pickup Unit The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid to electrostatic breakdown when servicing and handling the laser diode.
Page 21
SA-HT885WGC / SA-HT885WGS 11.3.2. Human body grounding 1. Use the anti-static wrist strap to discharge the static electricity form your body.
SA-HT885WGC / SA-HT885WGS 12 Disassembly and Main Component Replacement Procedure “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
SA-HT885WGC / SA-HT885WGS 12.3. Disassembling the Top Cabinet Step 1 Unscrew the screw. Step 2 Lift up and remove the top cabinet. 12.4. Disassembling the Lid assembly (When taking out disc manually) · Follow the (Step 1) - (Step 2) of Item 12.3.
SA-HT885WGC / SA-HT885WGS 12.5. Disassembling the Front Panel · Follow the (Step 1) - (Step 2) of Item 12.3. · Follow the (Step 1) - (Step 3) of Item 12.4. Step 1 Remove the lid assembly from the tray section.
SA-HT885WGC / SA-HT885WGS 12.9. Disassembling the Rear panel · Follow the (Step 1) - (Step 2) of Item 12.3. Step 1 Unscrew the screws. Step 2 Release the tabs. 12.8. Disassembling the DVD 12.10. Disassembling Main P.C.B. Module P.C.B. · Follow the (Step 1) - (Step 2) of Item 12.3.
SA-HT885WGC / SA-HT885WGS 12.11. Service Position 12.11.1. Servicing position of the DVD Module P.C.B. · Follow the (Step 1) - (Step 2) of Item 12.3. · Follow the (Step 1) - (Step 3) of Item 12.4. · Follow the (Step 1) - (Step 4) of Item 12.5.
SA-HT885WGC / SA-HT885WGS 13 Assembling and 13.2. Traverse Unit disassembling the DVD 1. Slide the lever (A) in the arrow direction (to the opposite side) till it stops. mechanism Unit 2. Slide the lever (A) further by bending the tab at the right side of the lever A in the right direction.
SA-HT885WGC / SA-HT885WGS 13.3. Tray Unit 1. Slide the guide tray unit while pressing the stopper in the 5. Remove the drive arm concave phase from the tray slider arrow direction, and remove the guide tray unit. and tray. (Assembling the tray unit) 2.
SA-HT885WGC / SA-HT885WGS 4. Remove the belt. 13.4. Loading section 5. Unlock the tab and remove the pulley. 6. Remove the relay gear. 1. Spread the tabs at the both sides and push out the drive arm shaft. 7. Turn the change lever in the arrow direction till it stops.
SA-HT885WGC / SA-HT885WGS 9. Pull the lever (B) in the bottom side to your side and remove 13.6. Optical Pickup Unit the change lever. 13.6.1. Procedure for Disassembling the Optical Pickup Unit 1. Spread the tabs to push in the pin.
Page 32
SA-HT885WGC / SA-HT885WGS 7. Unscrew the screw 8. Slide the shaft in the arrow direction. 4. Move the optical pickup unit in the arrow direction till it stops. 9. Lift the optical pickup unit with the shaft. 5. Unscrew the screws.
SA-HT885WGC / SA-HT885WGS (Assembling the optical pickup unit) 1. Pass the intermediate FPC through the frame hole. 2. Align the guide section of the optical pickup unit with the rail. 3. Install the shaft top to the holder. 11. Pull the shaft and the rubber out.
Page 34
SA-HT885WGC / SA-HT885WGS 7. Unscrew the screws with torx screw driver (T6). 8. Remove the spindle motor. 3. Remove the solders. 4. Remove the traverse motor. 5. Remove the solders. 6. Remove the screw lock as carefully as you can.
SA-HT885WGC / SA-HT885WGS 14 Optical Pick-up Self-Diagnosis and Replacement Procedure 14.1. Optical Pickup Breakdown Diagnosis The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use the following procedure for effective Self-diagnosis and tilt adjustment. Be sure to use the self-diagnosis function before replacing the optical pickup when "NO DISC"...
SA-HT885WGC / SA-HT885WGS 14.2. Service Mode Table 1 The service modes can be activated by pressing various button combination on the player and remote control unit. Player buttons Remote control unit buttons Application Note STOP Error code display (Refer to the item, “14.3.
Page 37
SA-HT885WGC / SA-HT885WGS Error Code Error Content Additional error explanation F890 Sending message when message is Sending message to AV task being sent to AV task F891 Message couldn’t be sent to AV task Begin sending message to AV task...
SA-HT885WGC / SA-HT885WGS 14.4. Service mode table 2 Pressing various button combinations on the player and remote control unit can activate the service modes.
SA-HT885WGC / SA-HT885WGS 14.5. Sales demonstration lock function This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCKED" is displayed on the unit, and ordinary operation is disabled.
SA-HT885WGC / SA-HT885WGS 15 Self-Diagnosis Function 15.2. Memorized Error Codes 15.2.1. Activating Self-Diagnosis Function 15.1. Automatic Displayed Error and Displaying Method Codes 1. Turn on the power. 15.1.1. Automatic Display Function 2. Select DVD/CD function. With no DVD/CD inserted in the...
SA-HT885WGC / SA-HT885WGS 16 Service Precautions 16.1. Recovery after the DVD player is repaired · When FLASH ROM IC or DVD module P.C.B. is replaced, carry out the recovery processing to optimize the drive. Playback the recovery disk to process the recovery automatically.
SA-HT885WGC / SA-HT885WGS 17 Adjustment Procedure 17.1. Service Tools and Equipment Application Name Number Tilt adjustment DVD test disc DVDT-S20 [SPG] TORX screw driver (T6) Available on sales route. (T6) or RFKZ0185 [SPG] Others Grease RFKXPG641 Harnal VFK1784 [SPG] Drysurf...
SA-HT885WGC / SA-HT885WGS 19 Voltage Chart 19.1. DVD Module P.C.B. IC8001 Re f No. MODE CD P LAY IC8001 Re f No. MODE CD P LAY IC8001 Re f No. MODE CD P LAY Re f No. IC8001 MODE CD P LAY Re f No.
SA-HT885WGC / SA-HT885WGS 19.2. Main P.C.B. Re f No. IC2006 MODE CD P LAY S TANDBY IC2010 Re f No. MODE CD P LAY -6.8 S TANDBY IC2011 Re f No. MODE CD P LAY S TANDBY Re f No.
SA-HT885WGC / SA-HT885WGS Re f No. Q2200 Q2201 Q2500 MODE -4.4 -4.4 CD P LAY -4.6 S TANDBY Q2600 Q2601 Q2604 Q2605 Re f No. MODE CD P LAY S TANDBY Q2607 Q2608 Q2609 Q2702 Q2703 Re f No. MODE CD P LAY -0.7...
SA-HT885WGC / SA-HT885WGS 21 Schematic Diagram Notes · This schematic diagram may be modified at any time Caution! with the development of new technology. IC and LSI are sensitive to static electricity. Notes: Secondary trouble can be prevented by taking care during S901: Play detection switch.
SA-HT885WGC / SA-HT885WGS 22 Block Diagram IC8001 IC8251 MN2DS0009AP C0GBG0000048 OPTICAL PICK UP UNIT DV3.2 LSI TRACKING COIL/FOCUS COIL/TRAVERSE/SPINDLE MOTOR DRIVE PHOTO DETECTOR VIN1 VOL4+ VIN2 TRAVERSE VIN4 HEAD MOTOR VIN3 LEVEL VOL4- SHIFT VIN8 BIAS1 VIN7 VHALF VIN6 TRV DRV...
Page 54
SA-HT885WGC / SA-HT885WGS IC8051 IC8001 IC8421 C3ABPG000145 MN2DS0009AP C0FBBK000050 64M SDRAM DV3.2 LSI AUDIO DAC OUTPUT AMP AND V OUT1 DVD MIX L LOW-PASS FILTER SRCK LRCK MEMORY MEMORY LRCK ADDRESS ADDRESS DATA2 V OUT2 DVD MIX R OUTPUT AMP AND...
Page 55
SA-HT885WGC / SA-HT885WGS TUNER PACK AM ANT FM ANT IC2006 C9ZB00000498 VIDEO DRIVE MIXER IF AMP BIAS COIL COIL RF AMP 150K BUFFER Y/PY/G CY IN 13.5MHz CY OUT JK2001 Y(RED) BIAS 150K (FM) CB/PB/B CB IN 13.5MHz CB OUT...
Page 57
SA-HT885WGC / SA-HT885WGS CN2012 SURR Rch SIGNAL LINES SURR Lch RF PCONT : MAIN SIGNAL LINE : AM SIGNAL LINE : DVD AUDIO SIGNAL LINE WIRELESS RF LINK : FM SIGNAL LINE : AM OSC SIGNAL LINE : DVD VIDEO SIGNAL LINE...
Page 62
SA-HT885WGC / SA-HT885WGS SCHEMATIC DIAGRAM-4 MAIN CIRCUIT :+B SIGNAL LINE :-B SIGNAL LINE :MAIN SIGNAL LINE :DVD(VIDEO) SIGNAL LINE :FM/AM SIGNAL LINE CN2004 VGND H2000 TRY OPEN PY/Y/G TRY OPEN TRY CLOSE C2206 50V4.7 VGND TRY CLOSE LINE R CB B...
Page 63
SA-HT885WGC / SA-HT885WGS SCHEMATIC DIAGRAM-5 MAIN CIRCUIT :+B SIGNAL LINE :-B SIGNAL LINE :MAIN SIGNAL LINE C2163 R2163 50V3.3 FRONTL C2263 R2263 C2623 R2122 50V3.3 FRONTR R2622 27K C2625 R2120 C2109 -7.5V 0.01 C2506 C2617 50V2.2 R2118 22K 0.01 R2619...
Page 64
SA-HT885WGC / SA-HT885WGS SCHEMATIC DIAGRAM-6 MAIN CIRCUIT :+B SIGNAL LINE :-B SIGNAL LINE :DVD(VIDEO) SIGNAL LINE Q2803 IC2801 B1BCCG000002 D2806 D2805 L2801 C0DAAMH00010 R2920 Regulator B0ECKM000016 B0ECKM000016 G0A101ZA0028 Regulator Q2800 R2813 C2811 B1BACD000018 C2806 D2801 0.01 R2823 R2822 Regulator 8.3V820 B0JCPD000025 2.2K...
Page 65
SA-HT885WGC / SA-HT885WGS SCHEMATIC DIAGRAM-7 MAIN CIRCUIT :+B SIGNAL LINE :MAIN SIGNAL LINE E2000 C2840 K4CZ01000027 CN2008 KEY2 KEY2 R2043 220 R2085 0 R2897 JOG A JOG A DC DET R2050 R2041 220 JOG B R2051 JOG B R2052 C2000...
Page 66
SA-HT885WGC / SA-HT885WGS SCHEMATIC DIAGRAM-8 FL CIRCUIT :+B SIGNAL LINE :MAIN SIGNAL LINE FL6000 A2BD00000140 R6051 C6005 50V22 POWER KEY1 H6010 +7.5V R6050 S6011 R6012 EVQ21405R R6038 MIC GND MIC CIRCUIT (CN6009)on SELECTOR R6011 SCHEMATIC D6006 MIC SW DIAGRAM-9 S6012...
SA-HT885WGC / SA-HT885WGS 27 Terminal Function of ICs 27.1. IC2018 (C2CBJG000672): Terminal Function Name System control HB_LVL Not used, open CMIX Not used, open Terminal Function SURR_FC1 Surround Freq. Limiter 1 Name SURR_FC2 Not used, open TRY_ Loading mechanism close SW ( L: SW...
SA-HT885WGC / SA-HT885WGS 28 Parts Location and Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used.
SA-HT885WGC / SA-HT885WGS 28.2. Component Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks Q2702 B1GDCFGA0018 TRANSISTOR PRINTED CIRCUIT BOARDS Q2703 B1ABEB000002 TRANSISTOR Q2800 B1BACD000018 TRANSISTOR REP3908G DVD MODULE P.C.B Q2801...
Page 82
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks D6006 B0BC5R000009 DIODE FP8251 K1MN06BA0148 6P CONNECTOR D6008 B0BC5R000009 DIODE FP8531 K1MN26BA0025 26P CONNECTOR D6010 B3AAA0000583 DIODE D8211 MA2J11100L DIODE COILS...
Page 83
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks W1208 ERJ6GEY0R00V CHIP RESISTOR R2002 ERJ3GEYJ221V 220 1/16W W2001 ERJ3GEY0R00V CHIP RESISTOR R2003 ERJ3GEYJ221V 220 1/16W W2002 ERJ3GEY0R00V CHIP RESISTOR R2006...
Page 84
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2085 ERJ3GEY0R00V 0 1/16W R2219 ERJ3GEYJ222V 2.2K 1/16W R2092 ERJ3GEYJ472V 4.7K 1/16W R2220 ERJ3GEYJ223V 22K 1/16W R2093 ERJ3GEYJ223V 22K 1/16W R2221...
Page 85
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2510 ERJ3GEYJ273V 27K 1/16W R2804 ERJ3GEYJ272V 2.7K 1/16W R2511 ERJ3GEYJ222V 2.2K 1/16W R2805 ERJ3GEYJ1R0V 1 1/16W R2521 ERJ3GEY0R00V 0 1/16W R2806...
Page 86
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2905 ERJ3GEYJ1R0V 1 1/16W R8324 ERJ2GEJ102X 1K 2W R2917 ERJ3GEY0R00V 0 1/16W R8325 ERJ3RBD101V 100 3W R2918 ERJ3GEY0R00V 0 1/16W R8326...
Page 87
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks RX8531 D1H456020001 CHIP RESISTOR C2156 ECJ1VB1A105K 1 10V RX8532 D1H85604A024 CHIP RESISTOR C2157 ECJ1VB1A105K 1 10V RX8533 D1H456020001 CHIP RESISTOR C2160...
Page 88
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C2403 ECJ1VB1A105K 1 10V C2822 ECJ1VB1E103K 0.01 25V C2404 ECEA1HKA3R3B 3.3 50V C2823 ECJ1VB1A105K 1 10V C2405 ECJ1VB1A105K 1 10V C2824...
Page 89
SA-HT885WGC / SA-HT885WGS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C8004 ECJ0EF1C104Z 0.1 16V C8502 ECJ0EF1C104Z 0.1 16V C8005 ECJ0EF1C104Z 0.1 16V C8503 ECJ0EF1C104Z 0.1 16V C8006 ECJ0EF1C104Z 0.1 16V C8504 ECJ0EF1C104Z 0.1 16V...
SA-HT885WGC / SA-HT885WGS 28.3. Packing Materials & Accessories Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks K2CQ2CA00002 AC CORD PACKING MATERIALS RJA0053-3X AC CORD [M]GS RQT8221-1B O/I BOOK [En] RPGX1584...