Honeywell ADEMCO VISTA-21iP Programming Manual page 18

*56 ZONE PROGRAMMING WORKSHEET
Zone
1
2
3
4
5
6
7
8
Zone
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
NOTES:
24
Zone Type: see chart in
∗56 Zone Programming 25
Menu mode section.
26
27
Report Code: enabled if
first digit is a non-zero 28
number
29
30
Hardwire Type (zns 2-8):
0 = EOL 3 = ZD
31
1 = NC 4 = DB
32
2 = NO
33
Input Type:
34
2 = AW (zones 9-48)
35
3 = RF (zones 9-48)
36
4 = UR (zones 9-48)
5 = BR (zones 49-64) 37
NOTE: Zones 9-16 not
38
available if zone
39
doubling enabled.
40
Response Time:
41
0 = 10msec
42
1 = 350msec
43
2 = 700msec
3 = 1.2 sec
44
45
Reserved Zones
46
47
91 =
addressable device
report enable/disable 48
default zone type =
49
[05].
50
92 =
Duress report
51
enable/disable
52
53
54
55
56
57
58
59
60
61
62
63
64
95
96
99
Zn Type Part. Report Hardwire
[09] [1]
[01] [1]
[03] [1]
[03] [1]
[03] [1]
[03] [1]
[03] [1]
[03] [1]
Zn Type Part. Report Input Type
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[00] N/A
**
[00] N/A
**
[06] N/A
**
** Emergency key zones 95, 96, and 99 report the partition of the keypad used to activate the emergency zones.
[default shown in brackets]
Rsp. Time
Type
[EOL] [1]
[EOL] [1]
[EOL] [1]
[EOL] [1]
[EOL] [1]
[EOL] [1]
[EOL] [1]
[EOL] [1]
Loop
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[RF]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
[BR]
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
WWW.DIYALARMFORUM.COM
– 18 –
Location
Serial No.
keypad [1] / [∗]
keypad [3] / [#]
keypad [∗] / [#]
Location