Page 1
COMPACT COMPONENT SYSTEM SYSTEME DE COMPOSANTS COMPACT NX-PN10 INSTRUCTIONS MANUEL D’INSTRUCTIONS LVT2011-002B...
Page 2
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
Page 3
For Canada/pour le Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS. CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B...
Page 4
Caution: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below. 3.
Contents Introduction... 2 Precautions ... 2 Getting Started... 3 Connections... 4 Canceling the Display Demonstration (Demo) ... 6 Turning on the Power Automatically (Motion Sensor) ... 6 Basic Operations ... 7 Main Unit ... 7 Remote Control ... 9 Playing Back from iPod Devices... 12 Connecting iPod ...
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C.
Getting Started • In this manual, operations using the remote control are mainly explained; however, you can use the buttons and controls on the unit if they have the same (or similar) name and marks. • In this manual, “iPod” means both iPod and iPhone devices.
Connections Do not connect the AC power cord until all other connections have been made. Connecting the Antenna FM antenna (supplied): Extend it so that you can obtain the best reception. For better FM reception Disconnect the supplied FM antenna and connect to an outdoor FM antenna using a 75 wire with coaxial type connector.
Page 9
Connecting the Video Cord to View a Video/Picture from iPod When viewing a video/picture from iPod on your TV, use a composite video cord (not supplied) to connect the VIDEO OUT jack on the unit and the composite video input on your TV. •...
Canceling the Display Demonstration (Demo) When you connect the AC power cord for the first time, the display demonstration starts automatically. • When you operate the unit, the display demonstration stops temporarily. If no operation is done for about 2 minutes, the unit starts the display demonstration again. Button On the unit Hold down until “DEMO OFF”...
Basic Operations Main Unit Illumination panel (P.10) STANDBY lamp Operating on the Main Unit Buttons Turns on or off (standby) the power. Activates or deactivates Motion Sensor (P.6). Dock A Dock B (P.13) (P.13) Display (P.8) Operations Motion sensor (P.6) Remote control sensor...
Buttons Activates or deactivates the display demonstration (P.6). Adds the powerfulness to the sound (P.11). Stops the timer sound and restarts it 5 minutes later (P.22). • iPod (P.14): Press: Reverse skip/forward skip. Hold down: Reverse search/forward search. • FM (P.17): Tunes in to a station. •...
Symbols Lights up when FM stereo broadcast is received. Lights up when FM monaural reception mode is activated. MONO Lights up when an FM station of sufficient signal strength is tuned in. TUNED Lights up when FM is selected as the source. •...
Page 14
Buttons Changes the display information. • For iPod A/iPod B/AUDIO IN: Source name • For FM: Frequency Changes the source to FM (P.17) or AUDIO IN (P.19). • Changes the source to iPod • Starts playback and pauses for iPod (P.14). Adjusts the volume level (VOL MIN/VOL 0 to VOL MAX/VOL 30).
Page 15
To turn off the unit after a certain period of time—Sleep Timer Press repeatedly to specify the time (in minutes) as follows: (Canceled) • To check the time remaining before the shut-off time, press SLEEP once. If you press the button repeatedly, you can change the shut-off time.
• For details about updating iPod, check on the Apple web site <http://www.apple.com>. • JVC does not assure the compatibility of iPod released after April 2009 with this unit. • “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards.
Connecting iPod Connect iPod to dock A or B on the unit. You can have 2 iPod devices connected at the same time. • Make sure the unit is on standby when you connect iPod. Dock A Dock B To detach the dock adapter from the dock: Pull up the dock adapter with your fingernail or a sharp-pointed tool using the slot.
Operations For details, also refer to the instruction manual for iPod. NOTES: • Before viewing a video/picture from iPod on your TV, make the appropriate video setting on iPod. For details of the setting, see the instruction manual for iPod. •...
Page 19
Buttons On the On the unit remote — — — Not equipped with iPhone and iPod touch. Operations Confirms an item on the menu/screen. Press: Applies Shuffle Play to iPod selected as the source. Select the desired shuffle mode. “SHUFFLE” appears for a while. •...
Page 20
NOTES: • JVC is not responsible for any loss of or damage to iPod that might result from the use of this product. • Do not touch or hit the terminals of the dock and of iPod. It might cause damage to these terminals.
Listening to FM Broadcasts Basic Operations Buttons On the unit On the remote — — AM band is not received with this unit. Operations Selects FM as the source. AUDIO IN When an FM program is broadcasted in stereo, ST (stereo) lights up on the display (only when the reception is good).
Presetting Stations You can preset 30 FM stations. Select FM as the source. Tune in to the station you want to preset. • You can also store the monaural reception mode for FM preset stations if selected. Activate the preset number entry mode. “SET”...
Playing Back from Other Equipment Connecting Other Equipment By using a stereo mini plug cord (not supplied), you can connect other equipment with analog audio output jacks, such as a portable audio player, etc. To headphones or audio out Stereo mini plug cord Portable (not supplied) audio player...
Setting the Clock and Timer Setting the Clock Set the built-in clock before using Timer. • You can set the clock when the unit is turned on or on standby. Activate the clock setting mode. “ADJCLOCK” appears then the hour digit of the time indication flashes on the display.
Page 25
Select Timer you want to set. TIMER 1 Select Timer type. WEEKLY WEEKLY: See step 4 below. ONCE: Timer works once on a selected day of the week. Select the desired day of the week. • When “WEEKLY” is selected in step 3: SUN DAY THU DAY MON-SAT...
Page 26
To Cancel Timer Select Timer you want to cancel. TIMER 1 TIMER 3 “CANCEL” flashes on the display. icon and the timer number indicator (1/2/3) disappear. NOTE: The settings you have made are memorized though you cancel Timer. To Turn off the Timer Sound briefly Using Snooze, you can have the timer sound stop and restart it 5 minutes later.
Troubleshooting If you have a problem with your unit, check this list for a possible solution before calling for service. General Power does not come on. The power plug is not inserted securely. Plug it in securely (P.5). Power turns on even though you turned off.
Accessories See page 3. Amplifier Output Power 10 W (5W+5W) at 8 (10%THD) Ω Terminals AUDIO IN Input Sensitivity/Impedance (1 kHz): LEVEL 1: 500 mV/47 k Ω LEVEL 2: 315 mV/47 k Ω LEVEL 3: 125 mV/47 k Ω Dock A and B for iPod/iPhone Compatible iPod/iPhone models: See page 12.
Page 29
Table des matières Introduction... 2 Précautions ... 2 Pour commencer ... 3 Connexions... 4 Annulation de la démonstration des affichages (Demo) ... 6 Mise sous tension automatique de l’appareil (Capteur de mouvement)... 6 Opérations de base... 7 Appareil... 7 Télécommande ... 9 Lecture à...
Merci pour avoir acheté un produit JVC. Veuillez lire attentivement toutes les instructions avant d’utiliser l’appareil afin de bien comprendre son fonctionnement et d’obtenir les meilleures performances possibles. Précautions Installation • Installez la chaîne dans un endroit plat, sec, et ni trop chaud, ni trop froid—entre 5°C et 35°C.
Pour commencer • Dans ce manuel, nous expliquons principalement les opérations à l’aide de la télécommande; cependant, vous pouvez utiliser les touches et les commandes de l’appareil si elles portent le même nom (ou un nom similaire) et la même marque. •...
Connexions Ne branchez pas le cordon d’alimentation secteur avant d’avoir effectué toutes les autres connexions. Connexion de l’antenne Antenne FM (fournie): Étendez-la de façon à obtenir la meilleure réception possible. Pour une meilleure réception FM Déconnectez l’antenne FM fournie et connectez l’appareil à...
Page 33
Connexion de cordon vidéo pour voir une séquence vidéo/image de l’iPod Pour afficher une séquence vidéo ou d’une image à partir de votre iPod sur votre téléviseur, utilisez un cordon vidéo composite (non fourni) et connectez-le à la prise VIDEO OUT sur l’appareil et à l’entrée vidéo composite du téléviseur.
Annulation de la démonstration des affichages (Demo) Quand vous connectez le cordon d’alimentation pour la première fois, la démonstration des affichages démarre automatiquement. • Quand vous utilisez l’appareil, la démonstration des affichages s’arrête temporairement. Si aucune opération n’est réalisée pendant environ 2 minutes, l’appareil démarre de nouveau la démonstration des affichages.
Opérations de base Appareil Panneau d’illumination (P.10) Témoin STANDBY Fonctionnement sur l’appareil Touches Met en marche/arrête (met en veille) l’appareil. Met en ou hors service le capteur de mouvement (P.6). Dock A Dock B (P.13) (P.13) Affichage (P.8) Opérations Capteur de mouvement (P.6) Capteur de...
Page 36
Touches Met en ou hors service la démonstration des affichages (P.6). Ajoute de la puissance au son (P.11). Arrête le son de la minuterie et le redémarre 5 minutes plus tard (P.22). • iPod (P.14): Appuyez sur: Saut vers l’arrière/saut vers l’avant. Maintenez pressée la touche: Recherche vers l’arrière/vers l’avant.
Symboles S’allume quand une émission FM stéréo est reçue. S’allume quand le mode de réception FM monophonique est en service. MONO S’allume lors de la réception d’une station FM dont le signal est suffisamment fort. TUNED S’allume quand FM est choisi comme source. •...
Page 38
Touches Change les informations de l’affichage. • Pour iPod A/iPod B/AUDIO IN: Nom de la source • Pour FM: Fréquence Change la source sur FM (P.17) ou AUDIO IN (P.19). • Change la source sur iPod • Démarre et interrompt la lecture pour iPod (P.14). Adjuste le niveau de volume (VOL MIN/VOL 0 à...
Page 39
Pour mettre l’appareil hors tension après une certaine période de temps—Minuterie d’arrêt Appuyez répétitivement sur la touche pour spécifier la durée (en minutes) de la façon suivante: (Annulée) • Pour vérifier le temps qui reste avant que l’appareil s’éteigne automatiquement, appuyez une fois sur SLEEP.
• Pour en savoir plus sur la mise à jour de l’iPod, consultez le site Web de Apple <http://www.apple.com>. • JVC n’assure pas la compatibilité de cet appareil avec les iPod mis en vente après avril 2009. • “Made for iPod” et “Made for iPhone” signifient qu’un accessoire électronique a été conçu pour être connecté...
Connexion de iPod Connectez l’iPod au dock A ou B de l’appareil. Vous pouvez connecter 2 iPod en même temps à l’appareil. • Assurez-vous que l’appareil est en mode d’attente quand vous connectez un iPod. Dock A Dock B Pour détacher l’adaptateur de dock du dock: Tirez sur l’adaptateur de dock avec le bout de votre doigt ou un outil pointu que vous insérez dans la fente.
Opérations Pour plus d’information, référez-vous aussi au mode d’emploi fourni pour votre iPod. REMARQUES: • Avant de regarder une séquence vidéo/image à partir de iPod sur votre téléviseur, faites réglages vidéo appropriés sur le iPod. Pour en savoir plus sur les réglages, référez-vous au manuel d’instruction de iPod.
Page 43
Touches Sur la Sur l’appareil télécommande — — — Non disponible sur le iPhone et iPod touch. Opérations Valide un élément sur le menu ou sur l’écran. Appuyez sur: Applique la lecture aléatoire à l,iPod ou à l’iPod choisi comme source. Choisissez le mode de lecture aléatoire souhaité.
Page 44
REMARQUES: • JVC ne peut être tenu responsable pour toute perte ou dommage à iPod résultant de l’utilisation de ce produit. • Ne touchez pas ni ne frappez les prises du dock et du iPod. Cela pourrait endommager ces bornes.
Écoute d’émissions FM Opérations de base Touches Sur la Sur l’appareil télécommande — — La bande AM ne peut pas être reçue avec cet appareil. Opérations Choisit FM comme source. AUDIO IN Quand un programme FM est diffusé en stéréo, l’indicateur ST (stéréo) s’allume sur l’affichage (uniquement quand la réception est bonne).
Page 46
Préréglage des stations Vous pouvez préréglez 30 stations FM. Choisissez FM comme source. Réglez la station que vous souhaitez mémoriser. • Vous pouvez aussi mémoriser le mode de réception monophonique pour les stations FM préréglée s’il est choisi. Mettez en service le mode d’entrée de numéro de préréglage. “SET”...
Lecture à partir d’un autre appareil Connexion d’un autre appareil En utilisant un cordon à mini-fiche stéréo (non fourni), vous pouvez connecter un autre appareil muni de prises de sortie audio analogique tel qu’un lecture audio portable, etc. Au casque d’écoute ou à...
Réglage de l’horloge et de la minuterie Réglage de l’horloge Réglez l’horloge intégrée avant d’utiliser la minuterie. • Vous pouvez régler l’horloge quand l’appareil est sous tension ou en mode d’attente. Mettez en service le mode de réglage de l’horloge. “ADJCLOCK”...
Page 49
Choisissez la minuterie que vous souhaitez régler. TIMER 1 Choisissez le type de minuterie. WEEKLY WEEKLY: Voir l’étape 4 ci-dessous. ONCE: La minuterie fonctionne une fois le jour choisi de la semaine. Choisissez le jour de la semaine souhaité. • Quand “WEEKLY” est choisi à l’étape 3: SUN DAY THU DAY MON-SAT...
Page 50
Pour annuler la minuterie Choisissez la minuterie que vous souhaitez annuler. TIMER 1 TIMER 3 “CANCEL” clignote sur l’affichage. L’icône REMARQUE: Les réglages que vous avez réalisés sont mémorisés bien que vous ayez annulez la minuterie. Pour interrompre brièvement le son de la minuterie En utilisant le rappel d’alarme, vous pouvez interrompre le son de la minuterie et le reprendre 5 minutes plus tard.
Guide de dépannage Si vous des problèmes avec votre appareil, cherchez d’abord une solution dans cette liste avant d’appeler un réparateur. Général L’alimentation n’arrive pas. La fiche d’alimentation n’est pas insérée correctement. Insérez-la solidement (P.5). L’appareil ser met sous tension même si vous l’avez mis hors tension.
Spécifications Accessoires Voir page 3. Amplificateur Puissance 10 W (5W+5W) à 8 Ω (10%DHT) Prises AUDIO IN Sensibilité/Impédance d’entrée (1 kHz): LEVEL 1: 500 mV/47 k Ω LEVEL 2: 315 mV/47 k Ω LEVEL 3: 125 mV/47 k Ω Dock A et B pour iPod/iPhone Modèles d’iPod/iPhone compatibles: Voir page 12.