JVC LVT2110-022A Instructions

ENGLISH
MICRO COMPONENT SYSTEM
UX-G375
INSTRUCTIONS
—Consists of CA-UXG375 and SP-UXG375
Thank you for purchasing a JVC product.
For turning off the demonstration display, see
"Canceling the display demonstration".
©2010 Victor Company of Japan, Limited
Precautions
Notes on the power cord Notes on installation
• When you are away on travel or otherwise for an • Select a place which is level, dry and neither too hot nor
extended period of time, remove the plug from the wall too cold—between 5˚C and 35˚C.
outlet. • Do not install the System in a place subject to
• When unplugging the System from the wall outlet, vibrations.
always pull the plug, not the power cord. • Do not put heavy objects on the System.
• Do not handle the power cord with wet hands.
To prevent malfunction or damage of the System
• Disconnect the power cord before cleaning the System
• Do not insert any metallic objects, such as wires,
or moving the System.
hairpins, coins, etc. into the System.
• Do not alter, twist or pull the power cord, or put
• Do not block the vents.
anything heavy on it, which may cause fire, electric
shock, or other accidents.
There are no user-serviceable parts inside. If anything
• If the cord is damaged, consult a dealer and have the
goes wrong, unplug the power cord and consult your
power cord replaced with a new one.
dealer.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
• Do not expose the System to direct sunlight or place it
near a heating device.
Maintenance
To get the best performance of the System, keep your discs and mechanism clean.
Handling discs Cleaning the System
• Remove the disc from its case by holding it at the edge • Stains should be wiped off with a soft cloth. If the
while pressing the center hole lightly. System is heavily stained, wipe it with a cloth soaked in
• Do not touch the shiny surface of the disc, or bend the water-diluted neutral detergent and wrung well, then
disc. wipe clean with a dry cloth.
• Put the disc back in its case after use. • Since the System may deteriorate in quality, become
• Be careful not to scratch the surface of the disc when damaged or get its paint peeled off, be careful about
placing it back in its case. the following:
• Avoid exposure to direct sunlight, temperature – DO NOT wipe it with a hard cloth.
extremes, and moisture. – DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
To clean the disc:
– DO NOT apply any volatile substance such as
• Wipe the disc with a soft cloth in a straight line from
insecticides to it.
center to edge.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.
CAUTION: Proper Ventilation Front view
To avoid risk of electric shock and fire,
and to prevent damage, locate the
apparatus as follows:
SP-UXG375
1. Front: No obstructions and open
spacing.
2. Sides/Top/Back: No obstructions
should be placed in the areas shown
by the dimensions on the right. Side view
3. Bottom: Place on the level surface.
Maintain an adequate air path for
ventilation by placing on a stand
with a height of 10 cm or more.
Specifications
Amplifier section General
OUTPUT POWER: 60 W (30 W + 30 W) at 6 Ω (10% THD) Power requirements:
Speakers/Impedance: 6 Ω – 16 Ω
Audio input
AUDIO IN: 500 mV/47 kΩ (at "LEVEL 1") Power consumption:
LVT2110-022A[UW]
250 mV/47 kΩ (at "LEVEL 2")
0310NYMCRECDT
125 mV/47 kΩ (at "LEVEL 3") Dimensions (W x H x D):
Digital input: USB MEMORY Mass:
Tuner section Speakers
FM tuning range: 87.50 MHz - 108.00 MHz Speaker units:
AM tuning range: 531 kHz - 1 710 kHz Impedance:
(in 9 kHz spacing) Dimensions (approx.):
530 kHz - 1 710 kHz
(in 10 kHz spacing) Mass (approx.):
CD player section
Specifications and appearance are subject to change
Dynamic range: 88 dB
without prior notice.
Signal-to-noise ratio: 85 dB
Wow and flutter: Immeasurable
USB section
USB specification: Compatible with USB 2.0 Full Speed
Microsoft and Windows Media are either registered
Compatible device: Mass storage class
trademarks or trademarks of Microsoft Corporation in
Compatible file system: FAT16, FAT32
the United States and/or other countries.
Output power: DC 5 V 500 mA
Troubleshooting
If you are having a problem with your System, check this list for a possible solution before calling for service.
General
\ Power plug is not inserted securely. Plug in securely.
Power does not turn on.
\ There is a time limit. Repeat the procedure again.
Adjustments or settings are suddenly
canceled before you finish.
\ The built-in microprocessor may malfunction due to external
Operations are disabled.
electrical interference. Unplug the AC power cord and then plug it
back in.
\ The path between the remote control and the remote sensor on
Unable to operate the System from the
remote control. the System is blocked.
\ The batteries are exhausted.
\ Speaker connections are incorrect or loose.
No sound is heard.
\ Headphones are connected.
Disc/USB Mass Storage Class Device Operations
\ The disc is placed upside down. Place the disc with the label side
The disc/USB mass storage class device does
not play. up.
\ The disc is recorded with the "packet writing (UDF file system)". It
cannot be played. Check the files you want to play back.
\ The USB mass storage class device is not connected properly.
\ Playing order is determined when the groups and tracks were
MP3/WMA groups and tracks are not played
back in order as you expect. recorded. It depends on the writing application.
\ The disc is scratched or dirty.
The disc/USB mass storage class device
\ MP3/WMA files have not been properly copied into the USB mass
sound is discontinuous.
storage class device.
\ Static electricity may stop the sound. In this case, disconnect and
Sound from USB mass storage class device is
interrupted. connect the USB mass storage class device again after turning off
the System.
\ The AC power cord is not plugged in.
The disc tray does not open or close.
\ Disc ejection is prohibited (see page 2).
Radio Operations
\ Antennas connections are incorrect or loose.
Hard to listen to broadcasts because of noise.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
Daily Timer Operations
\ The System has been turned on when the on-time comes. Timer
Daily Timer does not work.
starts working only when the System is turned off.
\ There might have been a power failure, set the clock first, then the
time again.
JVC bears no responsibility for any loss of data in USB mass storage class device while using this System.
Getting started
❍
Supplied Accessories
SP-UXG375 After unpacking, check to be sure that you have all
the following items.
• Remote control (× 1):
CA-UXG375
– RM-SUXG355U (for UX-G375)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed in the remote
control when shipped from the factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
CA-UXG375 • AC plug adapter (× 1)
If anything is missing, consult your dealer
immediately.
Connections
Do not connect the AC power cord until all other connections have been made.
AC 110 V-127 V/AC 220 V-240 V
adjustable with the voltage selector, NOTES:
50 Hz/60 Hz • Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep
30 W (power on) the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor
1.00 W or less (standby) reception.
165 mm x 251 mm x 245 mm • Make sure both the speakers are connected correctly and firmly.
1.9 kg • When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
10 cm cone x 1
6 Ω
To connect the speaker cords
140 mm x 251 mm x 141 mm
(W/H/D)
1.3 kg each
Red
From right
speaker
Black
Mains (AC) Line Instruction
CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC)
line voltage corresponds with the position of the voltage
selector switch provided on the outside of this equipment
and, if different, reset the voltage selector switch, to prevent
from a damage or risk of fire/electric shock.
Sound and other adjustments
Initial settings
Canceling the display demonstration
When the System is turned on and no operation is
done for about 2 minutes, the display demonstration
automatically starts.
To cancel the display demonstration temporarily, press
and hold DEMO while the System is turned on, until
"DEMO OFF" appears.
DEMO
Display settings
Dim the display
You can dim the display window and illumination
lamp.
While the System is turned on...
DIMMER
Change the display information
DISPLAY
The display information changes as follows:
FM/AM: Frequency = Clock
•
CD: Current track elapsed time = Clock
•
MP3/WMA: Current track elapsed time = ID3 tag
•
= Current group/track = Clock
1
❍
Prepare the Remote Control
When you use the remote control for the first time, pull out the insulation sheet.
To Replace the Battery in the Remote Control
NOTES:
Lithium coin battery
• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.
(product number: CR2025)
• To prevent the battery from overheating, cracking, or starting a fire:
– Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal, state, and local regulations.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best
reception.
To assemble the AM loop antenna
From left
speaker
To a wall outlet
Plug the AC power cord only after all connections are complete.
Timers
Setting the clock Setting the Sleep Timer
Set the built-in clock before using Daily timer or Sleep Press repeatedly to specify the time (in minutes) as
Timer. follows:
1. Press and hold CLOCK/TIMER.
AUTO STBY 10
CLOCK/
SLEEP
TIMER
• The SLEEP indicator lights up.
2.
Press SET. • To check the remaining time until the System shuts
off, press once.
SET
Turning Off the System Automatically
—AUTO STANDBY (only for CD/USB)
3.
Adjust the hour, then the minute. Press and hold until the A.STBY indicator lights on the
display.
UP or SET
DOWN
AUTO STBY
• To go back to the previous step, press CANCEL. SLEEP
• If you have already adjusted the clock before,
perform steps 1 to 3.
• The A.STBY indicator starts flashing after playback
stops. If no operation is done for about 3 minutes, the
System turns off.
Sound adjustments
• To cancel this function, press and hold again.
Drop the volume in a moment
FADE
MUTING
• To restore the volume, press again, or adjust the
volume level.
Emphasize the sound (Sound Turbo)
SOUND TURBO
• The S.TURBO indicator lights up.
• To cancel this function, press again.
Reinforce the bass sound (Hyper Bass Sound)
HBS
• The BASS indicator lights up.
• When Sound Turbo function is activated (see
above), the BASS indicator goes off and HBS
button does not work.
• To cancel this function, press again.
Adjust the tone (Bass/Treble)
Press once for adjusting the bass level; twice for
treble level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
BASS/TREBLE
NOTE:
VOLUME
The operations are explained using the remote control, unless mentioned otherwise. However, if the System has the
same or similar button names, they can also be used for the operations.
For better FM reception Outdoor FM antenna
(not supplied)
Disconnect the supplied FM antenna, and
connect to an outdoor FM antenna using
FM antenna (supplied)
a 75 Ω wire with coaxial type connector.
To connect the AM loop antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception is obtained.
NOTE:
Keep the AM loop antenna cable wrapped
around the AM loop antenna frame,
otherwise the effectiveness and sensitivity
of the AM loop antenna may be reduced.
Black
White
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite
music.
• You can store three Daily Timer settings.
20 30 60 90 120
• Tune into a station, place a CD, or connect a USB mass
OFF 180 150
storage class device to the System beforehand.
1.
Press CLOCK/TIMER repeatedly to display the
desired Daily Timer number ( 1/ 2/ 3 lights
up), then press SET during DAILY 1, DAILY 2 or
DAILY 3 is displayed.
CLOCK/
TIMER
SET
2. 1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—"CD", "USB",
"TUNER FM", or "TUNER AM".
4 Select the volume.
UP or SET
DOWN
• You can select the volume level –"VOLUME 0"
(VOL MIN) to "VOLUME 40" (VOL MAX) and
"VOLUME – –". If you select "VOLUME – –", the
volume is set to the last level when the System is
turned off.
3.
Turn off the System (on standby).
• When the on-time comes, the System sets the
volume gradually to the preset level.
• After you have set the Daily Timer and turn off
(standby) the system, the STANDBY lamp will start
flashing. (While on standby, indicator will not be
displayed.)
• To exit from the timer setting, press CANCEL as
required.
• To correct a misentry during the process, press
CANCEL. You can return to the previous step.
To Turn Off the Daily Timer
Press CANCEL when "DAILY" is lit up.