Panasonic CS-E9BKP Service Manual page 37

Panasonic ilmalämpöpumput korjaa ja huoltaa pääkaupunkiseudulla: Jäähdytinpalvelu RefGroup Oy
NAME OF EACH PART
Remote Control
1
2
AUT UTO HEA HEAT COOL COOL DR DRY FAN AN
AUT UTO
AUT UTO
ON
AUT UTO
OFF
FAN AN
TEMP
3
OFF/ON
POWERFUL
4
5
ECONOMY SLEEP
MODE
AIR SWING
FAN SPEED
6
1 2 3
7
SET
ON
8
OFF
CANCEL
TIMER
9
CHECK RESET CLOCK
0
Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.
PREPARATION BEFORE OPERATION
Indoor Unit
2
6
3
5
4
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
AUTO HEAT COOL DRY FAN
AUTO
4
Fit the air purifying filters in place
5
Insert the air filters
AUTO
FAN
6
Close the front panel
Remote Control
– To set the current time
AIR SWING
FAN SPEED
1 2 3
ON SET
OFF
CANCEL
TIMER
CHECK RESET CLOCK
1 Press 1.
2
Then press 2 to increase or decrease the time.
3 Press 1 again.
Set time at display will light up.
1 Signal Transmitter
2 Operation Display
3 Powerful Mode Operation Button
4 Room Temperature Setting Button
(self-illuminating button)
5 Operation Mode Selection Button
6 Vertical Airflow Direction Button
7 ON-Timer Button
8 OFF-Timer Button
!
9 Reset Point
(Press with fine-tipped object to clear the memory)
#
0 Check Point
To be used by the service technician only.
$
$
! OFF/ON Button
%
(self-illuminating button)
^
@ Sleep Mode Operation Button
&
# Fan Speed Selection Button
*
$ Horizontal Airflow Direction Button
(
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
HOW TO OPERATE
1 2
3
5
To start the operation
• Press 1.
• POWER indicator (green) on the indoor unit will light up.
(LED blinks when the room temperature is low at the
start of heating or operation mode is selected during
Automatic Operation.)
The power monitor lamps light up to show the
compressor operating condition.
• To stop, press once more.
Setting Mode
• Press 2 to select:-
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Fan Operation
AUTO – Automatic Operation
2
1
www.ilmalämpöpumput.com
37
CS-E9BKP CU-E9BKP5 / CS-E12BKP CU-E12BKP5
How to Insert the Batteries
2
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
About the batteries
• Can be used for approximately one year.
Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
(Not adjustable during Fan Operation.)
• Recommended temperature:
HEAT : 20°C ~ 24°C
COOL : 26°C ~ 28°C
DRY : Approx. room temperature
1
6
4
Automatic Operation
• At the start of the Automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the outdoor temperature, indoor temperature and
setting temperature.
• The operation mode changes every half hour, when
necessary.
(Ex) Setting Temperature at 25°C
36°C
32°C
31°C
H
E
A
T
I
18°C
N
G
16°C
13°C 19°C 21°C 23°C 25°C
Outdoor Temperature
1
S
C
O
O
F
O
T
L
I
D
N
R
G
Y