Yupiteru MVT-7100 Operating Instructions Manual page 6

~ c
~o rrection
key, see pages 16 & 17.
T
Enter key. Used to enter Frequencies, Increment steps and Receiving modes.
NC
Pressed first when you wish to use the secondary function of each key. details of which follow.
CONDARY KEY FUNCTIONS
7/1
ca. ~ es
to access any one of the facilities ddailed below the FUNC key mu.5t be pressed first.
T (I key)
1\ttenuator. When selected AJT will appear in the display. The attenuator can be selected on any
ndividual memory channel or frequency. In most cases the attenuator should be left 'off', if
1owever strong signals are present it is possible that some interference may occur. To reduce the
;trength of signal and reduce the possibility of interference the attenuator should be selected.
~emember
however that pressing FUNC + ATT will only activate the attenuator for that
Jarticular channel/frequency, no other channels or frequencies will be affected. If you wish to
>ctivate the attenuator for a different channel and frequency you must select the memory channel
:he press FUNC
+
A TT. To turn the attenuator off, select the channel.
An·
will show in the
jisplay then press FUNC + A TT again. AJT will clear from the screen indicating that the
iltenuator is no longer selected on that channel.. See page 3 5.
LAY (2 Key)
fhe delay facility will cause the MVT-7100 to pause for approximately 4 seconds after a
:ransmission has ended and before it continues to scan or search. Without delay selected the pause
ime is around 2 seconds.
DELAY
will show in the display. Pressing FUNC + DELAY again
·eturns the set to nonnal mode. See Page 35
IP (3 Key)
.vhen FUNC +SKIP is pressed in either Scan or Search mode this will cause the MVT-7100 to
:ontinue scanning or searching after approx. 5 seconds from when it stopped on that channel
or
i-equency even if the transmission has not finished . SKIP will show in the display. Pressing FUNC
• SKIP again returns the set to staying on a channel for the entire duration of the transmission.
;ee Page 35
I (.'IRCH Key)
;elects the monitor of the priority channel. See pages
21
& 22 for more on programming the
'riority channel.
VE (4 h"ey)
)elects and cancels the save function. See page 36.
EP (S Key)
~urns
the Keyboard beep on or off_ If
REEP
is showing at the bott om of the di sp lay then the
ound is on and a Beep sound will be heard each time a key is pressed . If
HJ·:u •
is not showing in
he display then no sound will be heard. See pages 35 & 36.
MVT-7100 Operating Instructions 1.0 © Javiation Janual)' I YY3.
Page
10
PGM
(6Key)
Used to select memory channels for the Program Scan mode. See pages 26 & 27.
MW (.'\CAN Key)
Memory Write.
Use~
when you wish to store a displayed frequency into a specific memory
channel. See pages 18, 19 &32 for further details.
M-+VFO (7 Key)
Transfers the frequency of a memory channel into manual mode when you will then be able to
tune up or down from that particular frequency. See page 20.
M-SCAN (8 Key)
Mode Scan. Used to start the Mode Scan facility. See page 28.
P-SCAN (9 Key)
Program Scan. Used to start the Program Scan. See page 26 & 27.
MODE (STEP Key)
Used in conjunction with either the rotary knob on the top of the set of the direction keys allows
you to change the mode of reception to either Wide FM, Narrow FM, AM, Lower Side Band
(LSB) or Upper Side Band (USB) on any frequency. See page 13 .
MHz (
1/tKey)
In conjunction with the C/ AC key can change the MHz digit of the display. See page 17.
SPR (0 Key)
Search Pass Read (what
1).
A new facility on the MVT-7100 is that you can specifY certain
frequencies (not channels) to be missed when searching. These can be frequencies with pennanent
interference on or maybe busy channels you just want to jump over. The Search Pass Read Key in
conjunction with the Rotary tuner or direction arrows allow you to see which frequencies you
have instructed the MVT-7100 to miss. For more details see pages 33 & 34 for further details.
BW (MRKey)
Bandwrite. Used for programming the frequency limits within Search banks. See pages 30 & 31.
PASS (OAC Key)
Used for 'locking out' any memory channel or channels you do not wish to monitor in the Scan
Mode. Also used to lock out specific individual frequencies (up to 500) when searching. See
pages 25, 33 & 34.
. ...... Time for a break before we get
down to the
"Real"
business of
button pressing ! .....
MVT'-7100 Operating Instructions 1.0 <0 Javiation Janumy 1993.
Page II
________________ . . . . . . . . . . . . . . . . . . . . . . . . . .
~
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -. . Gg . .
~~nr11
Til