Yupiteru MVT-7100 Operating Instructions Manual page 16

EXAMPLE
To search Bank 0
I . Press 0 (0 will flash)
2. Press SEARCH
The set will now start searching from 903.0375MHz to 904.9875MHz stopping on any active
frequencies. The 0 at the top right of the display indicated Bank 0 is being searched.
EXAMPLE
,'/-(. . . -
.
-;u .;
/ I \
snr - • -
12.5
lfHt FM
sC.al
903. 13'15
(;I!lD----
§ ]
PAl
To search Bank 9, between 850.025MHz and 859.9875MHz, FM, 6.25KHz steps.
I. Press 9
2. Press SEARCH
I I
PROGRAMMING NEW SEARCH BAND LIMITS
II
Whilst the pre-programmed bands may be a great interest to Fred Bloggs living in downtown Tokyo
they are of little use to you Fred Bloggs of downtown U.K.
To make the best use of the search banks we need to re-program them with frequencies of your own
interests. Try and keep the limits to just a few MHz as to increase the chance of receiving previously
unheard transmissions. Just do a few MHz at a time as it will prove far more productive than trying
to do the whole lot in one !
To program search limits is a relatively simple operation(!!), all we need to do is enter the start and
end frequencies into one of the I 0 search bands.
If you want to set the Mode and Increment steps that you wish to Search in you can do so in Manual
mode before you re-program any banks. You can however change the Mode and Increment steps of
any Search Bank while searching.
EXAMPLE
To program search Bank 6 to start at422.20MHz &finish at 422.30MHz
I. Ensure you are in manual mode and not searching or scanning (In the example he/ow the
set is /lined to 158. 35MHz, Narrow FM in 12.5KHz steps)
2. Press FUNC
+
BW (!he display
will now flash)
3. Press 4 2 2 • 2 (The bottom limit/the jreq11ency we wish to start at)
4. Press ENT
5. Press 4 2 2. 3 (The lop limit/the frequency we wish to finish at)
6. Press ENT
7. Press 6 (this is the bank we will store these limits in)
8. Press ENT (lf the "beep" is still on a do11ble beep will so1md to indicale the above has been
accepted the dipslay will ret11m to the previo11sjreq11ency in manual mode)
MVT-7100 Operating Instructions 1.0 10 Javiation January 1993.
Page 30
llfP
I
2.5Uil
FM
II: CI3C it it
t.:ID • .;:JI../.1..1
'
i
,
..
STEP-I 2 3' ~. 1 I I 0 -
'2.5*Hr;t(.,i
~ ,,,, ,
,, tC C1
:li:
,-,It /I
1-ID.-IJU.!../ .
' I l I I I
I
1'/ , \ \ \ I I I / / /
I
t
STI '-11 1~ ~6 1 19-;:,
r
1Hf'- 12l4~ 17 11 o...:..
I
'
1
1
':1511Hr""" F"' ' ' '''' I ,
I:JC*HY / i f l ! \ \ \ ' 1
- FJI!
~~·
c;: __ ,
FM
I
• i'\.d':r :r"
i •
~ ~~..t:r::r
::r ,,
I'
1
II..!.. .I: : II: 1:._1
~ ' ---------'~_J
l l(f P
Q:Jo:::Jo:::JD
Q]ITJ[IJCJ
SAVE DELAY DELAY SAVE DELAY DELAY
[IJ -- li@
r::::IJ--1
ENT
I
, DELAY
SKIP
(
snr 12l4~1 l ltl ~
sur
,
1
:u: . .
Hr/ / 11 ,
11 , ' ' \
tf , - ,
c
1cH1
.... 1 1!;; .
.;1
'\i:_// 1 ..
'~;.:',...t:IL!.",-,,-,
.... D
I
t.=tti •. :LIU.I..I
I ....
I''--~-
0
PGM
you have now re-programmed bank 6. When you
now press 6 + SEARCH
your set will search
bet ween 422.20MHz & 422.30MHz in Narrow FM and 12.5KHz increment steps.
EX AMPLE
' f i>
program search Bank 2 to start at 324.20MH:. &finish at 330.00MH::
1 . Ensure you are in manual mode and not searching or scanning
2. Press FUNC + BW (The display will now flash)
3. Press 3 2 4 . 2 (!he bottom limit/the frequency we wish to start at)
4. Press ENT
5. Press 3 3 0 (The top limit/the frequency we wish to finish at)
6. Press ENT
7. Press 2 (this is the bank we will store these limits in)
8. Press ENT
DON'T FORGET if you want to change the mode or increment steps you
can do so when the set is searching by simply by pressing FUNC
+
MODE
then rotating the rotary knob and pressing ENT or to change the steps just
press the STEP and rotate the tuning knob then press ENT
The same procedure should be used for re-programming any of the other
bands with frequency limits of you choice but remember keeping the limits to
just a few MHz (no more than say IOMHz) will greatly increase the chances
of locating previously unheard active frequencies .
MVT-7100 Operating lnstructions 1.0 0 Javiation January 1993.
Page 31