Storing Frequencies In Memory Channels; Memory Storage - Yupiteru MVT-7100 Operating Instructions Manual

STORING FREQUENCIES IN MEMORY CHANNELS FROM
MANUAL MODE
e MVT-7100 has 1000 memory channels, (plus one other when you count the priority channel)
ani
sed in 1 0 banks of I 00 channels into which you may program any frequency and mode,
nuator settings can also be stored . Memory channels are shown as
a
three digit number on the
of the display. It can be a good idea to group types of frequencies together, for example, store
your VHF airband frequencies in one bank, all the UHF airband frequencies in another and so
h .
store a frequency in a memory channel it is first necessary to follow the procedures for manual
ing described earlier. It is then a simple case of informing the MVT -7 I 00 which memory channel
J
wish to store the frequency in.
AMPLE
store J23.50MH:., AM mode, in channell3. (assuming the set is in AM,
if
not refer to the earlier
tion on selecting the correct mode and increment step size)
L Press 1 2 3 . 5
2 ~
Press ENT
3. Press 1 3
4. Press FUNC
+
MW
The MVT -7100 will confirm the entry by
a double beep (if the sound is on !) and temporally
show the memory channel on the left of the screen then return to normal Manual mode.
STEP
C
MtHz
.J Ll
AM
123.500.[/
GJITJCTID
A TI DELAY SKIP
o::::::J --+
I
ENT
I
BEEP
GJITJ
ATI SKIP
I (
m•
c
n•Hz
_, U AM
t:r~;: rtrt rt
IL .3.-ILILI.LI
.• I
~--------~~ ~--------~ MI~'---
MVf-7100 Operating Instructions 1.0
©
Javiation January 1993.
Page 18
EXAMPLE
To store 441.8125MHz. NFM mode in channel 127 (assuming the set is currelllly displaying
123.50, AM and 25KHz incremelll steps following the previous example)
I. Press FUNC +MODE
2. Rotate the tuning knob until FM is displayed
3. Press ENT
4. Press STEP
5. Rotate the tuning knob until 12.5KHz is shown
6. Press ENT
7. Press 4 4 I . 8 I 2 5
5. Press I 2 7
6. Press FUNC
7. Press MW
MEMORY STORAGE- CONSECUTIVE CHANNELS
A bit difficult to describe this one without being too long winded.
By pressing FUNC + MW without specifying a channel whilst a frequency is displayed in manual
mode will store this frequency shown into the LAST MEMORY CHANNEL DISPLAYED in
memory mode - so if memory channel 066 was displayed in either memory mode or scan mode and
you have manually entered 129.875MHz, pressing FUNC + MW will store 129.875MHz in channel
066 overwriting what was there before. Subsequent presses of FUNC + MW will result in
129.875MHz also in channels 67, 68, 69, 70 and so forth.
So if you want to store a set of frequencies in consecutive channels the following routine can be
used:-
I. Enter first frequency to be stored
2. Enter the channel number you wish to start at
3. Press FUNC + MW
4. Enter second frequency to be stored
5. Press FUNC
+
MW
6. Enter third frequency to be stored
7. Press FUNC + MW
After each press of FUNC + MW the channel number will appear on the screen for a short
moment.
.. ... and so forth BUT REMEMBER that storing a frequency in a memory channel will overwrite
any information that is already stored in that memory channel and if you do not enter a specific
channel at operation 2 above then the MVT-7100 will start to store frequencies from the last
memory channel that was displayed on the screen.
Mvr-7100 Operating Instructions 1.0
©
Javiation January 1993.
Page 19