All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WS 0665 BG CD Customer Service...
EN 2 LC4.9U AA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Connection Overview Index of this chapter: 1.1 Technical Specifications 1.2 Connection Overview Note: The following connector colour abbreviations are used 1.3 Chassis Overview (acc.
Page 3
Technical Specifications, Connections, and Chassis Overview LC4.9U AA EN 3 Cinch: PC Audio - In - D0- Data channel Rd - Audio - R 0.5 V / 10 kohm 10 - CLK+ Data channel Wh - Audio - L 0.5 V...
EN 4 LC4.9U AA Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes Notes Index of this chapter: 2.1 Safety Instructions 2.2 Warnings 2.3.1 General 2.3 Notes • Measure the voltages and waveforms with regard to the Safety Instructions chassis (= tuner) ground (H), or hot ground (I), depending on the tested area of circuitry.
Page 5
For the repair of such sets nothing changes. Philips CE is producing lead-free sets (PBF) from 1.1.2005 onwards. In case of doubt whether the board is lead-free or not (or with...
EN 6 LC4.9U AA Directions for Use 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
Mechanical Instructions LC4.9U AA EN 7 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal •...
Page 8
EN 8 LC4.9U AA Mechanical Instructions quick and easy with use of the delivered screws that can be tightened and loosened manually without the use of tools. See figure above. Note: Only use the delivered screws to mount the monitor to the stands.
Page 9
Mechanical Instructions LC4.9U AA EN 9 4.3.3 Side I/O Panel 4.3.4 LED Panel After removal of the Speaker Compartment Covers, this panel is accessible. 1. Disconnect the cable (1) from the panel. 2. Remove the T10 mounting screws [2] that hold the assy.
Page 10
EN 10 LC4.9U AA Mechanical Instructions 4.3.6 SSB Cover Shield 4.3.7 Small Signal Board F_15420_040.eps 070605 F_15430_049.eps Figure 4-12 SSB 100605 Figure 4-10 SSB cover shield 1. Remove the two fixation screws (1) that secure the SSB board on the lower part of the SSB shielding, see Figure “SSB”.
Page 11
Mechanical Instructions LC4.9U AA EN 11 4.3.9 Class D Audio Amplifier Panel F_15430_051.eps 100605 Figure 4-14 Class D audio amplifier panel 1. Disconnect all cables (1) from the panel. 2. Pinch the plastic fixation clamps (2) firmly between your fingers, and pull the panel upwards.
Page 12
EN 12 LC4.9U AA Mechanical Instructions 4.3.10 Plasma Display Panel / Glass Plate – Cable at LED panel. – Keyboard cable at SSB side. – Audio Amplifier supply cable at the Main Supply board. 1. Remove the T20 display panel mounting screws [1].
Page 13
Mechanical Instructions LC4.9U AA EN 13 4.3.11 PDP Glass Plate In order to remove/exchange the PDP glass plate: 1. Remove the PDP as described earlier. 2. Remove the T10 screws [1] from the mounting frame. 3. After removal of the frame, you can lift the glass plate from the set.
EN 14 LC4.9U AA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: How to Enter 5.1 Test Points To enter SDM, use one of the following methods: 5.2 Service Modes •...
Page 15
Service Modes, Error Codes, and Fault Finding LC4.9U AA EN 15 How to Navigate Menu Explanation Use one of the following methods: 1. LLLLL. This represents the run timer. The run timer counts • When you press the MENU button on the remote control, normal operation hours, but does not count standby hours.
Page 16
EN 16 LC4.9U AA Service Modes, Error Codes, and Fault Finding How to Store SAM Settings 8. Displays the detected Audio (e.g. stereo/mono). To store the settings changed in SAM mode, leave the top level 9. Displays the picture setting information.
Page 17
UART SERVICE CONNECTOR CONNECTOR Service Tools 5.4.1 ComPair Introduction ComPair (Computer Aided Repair) is a service tool for Philips I 2 C Power Consumer Electronics products. ComPair is a further 9V DC development on the European DST (service remote control), E_06532_021.eps 180804 which allows faster and more accurate diagnostics.
EN 18 LC4.9U AA Service Modes, Error Codes, and Fault Finding How to Order Error Codes ComPair order codes (US): • ComPair Software: ST4191. The error code buffer contains all errors detected since the last • ComPair Interface Box: 4822 727 21631.
Service Modes, Error Codes, and Fault Finding LC4.9U AA EN 19 5.5.3 Error Codes The Blinking LED Procedure In case of non-intermittent faults, write down the errors present Using this procedure, you can make the contents of the error in the error buffer and clear the error buffer before you begin buffer visible via the front LED.
Page 20
EN 20 LC4.9U AA Service Modes, Error Codes, and Fault Finding Table 5-3 NVM Default values (option bit settings through NVM Editor in SAM Mode) Byte Nr. Feature/Mode Description 42PF7320/28 Byte 0 QSS (LSB) Mode of quasi split sound amplifier...
Page 21
Service Modes, Error Codes, and Fault Finding LC4.9U AA EN 21 Byte Nr. Feature/Mode Description 42PF7320/28 Byte 5 Fast Filter 179(dec) No red reduction during blue stretch NTSC matrix Gamma control Control sequence of beam current limiting Low level of beam current limiter...
Page 22
EN 22 LC4.9U AA Service Modes, Error Codes, and Fault Finding No Picture Display (blank screen with correct sound output) 1. Check whether the user menu is visible. 2. If the user menu is OK, activate teletext mode. 3. If teletext is OK, the problem is in the ADC (B18) &...
Block Diagrams, Test Point Overviews, and Waveforms LC4.9U AA EN 23 6. Block Diagrams, Test Point Overviews, and Waveforms Wiring Diagram 42” FHP WIRING 42” FHP 8736 AUDIO AMPLIFIER 8735 PDP POWER SUPPLY 8102 INVERTER INVERTER 8323 0308 0311 1M03...
Block Diagrams, Test Point Overviews, and Waveforms LC4.9U AA EN 24 Wiring Diagram 42” SDI WIRING 42” SDI 8736 AUDIO AMPLIFIER 8735 PDP POWER SUPPLY CN308 8102 INVERTER INVERTER 1M03 1M46 RIGHT LEFT SPEAKER SPEAKER 8900 8146 8152 8120 1J01...
Block Diagrams, Test Point Overviews, and Waveforms LC4.9U AA EN 29 Supply Line Overview SUPPLY LINE OVERVIEW TOP CONNECTORS TUNER & IF SCALER SIDE CONNECTORS SIDE I/0 1M36 1K04 5102 5K00 0345 SUPPLY 5103 PANEL (PSU) LED PANEL 1M36 5K01...
Alignments LC4.9U AA EN 81 8. Alignments Index of this chapter: 8.1 General Alignment Conditions 8.2 Hardware Alignments 8.3 Software Alignments Note: Figures below can deviate slightly from the actual situation, due to the different set executions. General: The Service Default Mode (SDM) and Service Alignment Mode (SAM) are described in chapter 5.
EN 82 LC4.9U AA Alignments 8.3.1 SAM Menu 00035 LC4XAP1 1.14/S4XGNV 1.17 ERR 0 0 0 0 0 OP 000 057 140 032 120 128 000 . OP1 . Delta Cool Red . OP2 . Delta Cool Green -1 . OP3 .
Page 83
Alignments LC4.9U AA EN 83 8.3.3 ADC Gain and Grey Scale Alignment 8.3.4 Sound The table below shows a number of NVM settings used for • No adjustments needed for sound. each model of TV set. Be sure to use the correct editor in the SAM menu (NVM Editor or SC NVM Editor), because the first 8.3.5...
Page 84
EN 84 LC4.9U AA Alignments Table 8-3 Option codes in detail, at bit level Option byte & bit table for restoring the TV set to its original Factory Default settings via the NVM Editor in the SAM menu Model number...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 85 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: Crystal Clear. The block diagram below (Figure “Block 9.1 Introduction diagram”) shows the Pixel Plus architecture; the architectures 9.2 Block Diagram...
Page 86
HDMI in / PC-D: This input is directly going to the Scaler IC. See paragraph “Video: Scaler Part”. Tuner and IF A Philips UV1316E/1318SD/TEDE9 Tuner is used in the TV board. The SIF signals are decoded by the Hercules. Tuning is done via I...
Page 87
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 87 Video: TV Part (Diagrams B1, B2, and B3) Figure 9-3 Block diagram video processing...
EN 88 LC4.9U AA Circuit Descriptions, Abbreviation List, and IC Data Sheets The video processing is completely handled by the Hercules Comb filter. Such a signal must be bypassed. Notch mode • IF demodulator. is not even an option since e.g. in double window, one part •...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 89 about a “Field Comb Filter”. Field Comb filters are only for PAL The offset block receives the motion dependant 2D/3D Comb of commercial interest. filtered signal as input. The black level of the luminance signal Field Comb filters show also problems on vertical colour is restored and the result is output.
Page 90
EN 90 LC4.9U AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.6.3 Noise Reduction and Noise Estimator Video: Scaler Part (Diagram B7, B8 and B9) The noise reduction function is a sophisticated successor of the The Genesis gm1501 Scaler is a dual channel graphics and...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 91 9.7.1 Teletext Path Audio Processing In Pixel Plus and Digital Crystal Clear models, which have an Hercules ADC (B18) and Columbus 3D combfilter (B19), the digital input of the scaler is used for the digital video signal (Columbus...
Page 92
P1.3 • On-chip x86 micro-controller (OCM) from Genesis LCD or plasma TV/Monitor Controller. 108 P1.6/ SCL • On-chip 80C51 micro-controller from Philips 109 P1.7/ SDA Semiconductor UOCIII (Hercules) series. 111 P2.0/ TPWM SOUND_ENABLE P2.0 Each micro-controller has it own I C bus which hosts its own 112 P2.1/ PWM0...
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 93 • LED. This signal is used as an indication for the Standby, 9.10 Abbreviation List Remote and Error Indicator. Region diversity: – During protection mode, the LED blinks and the set is...
Page 94
Red, Green, Blue, Horizontal sync, LATAM LATin AMerica and Vertical sync Read Only Memory LC04 Philips chassis name for LCD TV 2004 project Service Alignment Mode Liquid Crystal Display SandCastle: two-level pulse derived Light Emitting Diode; A semiconductor from sync signals...
Page 95
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switched Mode Power Supply SouND SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace; This is a consumer interface used to transfer digital audio SRAM Static RAM STBY STandBY SVHS...
EN 96 LC4.9U AA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.11 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs).
Page 97
Circuit Descriptions, Abbreviation List, and IC Data Sheets LC4.9U AA EN 97 9.11.2 Diagram B19, Type T6TU5XB (IC7M00, Columbus) Figure 1 Package outline (top view) WEB/ UVA0 UVA2 UVA4 UVA6 UVA8 SEL656 TST1 HREF DAVB /Di0 /Di2 /Di4 /Di6 /Di8...
EN 106 LC4.9U AA Revision List 11. Revision List Manual xxxx xxx xxxx.0 • First release. Manual xxxx xxx xxxx.1 • I2C Diagram positioned. • Spare Parts List added.