Basic Settings; Recording A Source; Adjusting The Front Speaker Output Balance; Setting The Subwoofer Information - JVC RX-6000VBK Instructions Manual

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while
others will make operations easier.

Recording a Source

You can record any source playing through the receiver to a cassette
deck (or an MD recorder) connected to the TAPE/MD jacks and the
VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like, without affecting the sound levels of
the recording.
Note:
The output volume level, tone adjustment (see page 10), bass boost
(see page 10) and DSP modes (see page 18) cannot affect the
recording.
Adjusting the Front Speaker Output
Balance
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press ADJUST repeatedly until
"L/R BALANCE" appears on the
display.
• Once you have pressed ADJUST, MULTI CURSOR % / fi can
be also used for selecting "L/R BALANCE."
2. Press MULTI CURSOR @ / # to
adjust the balance.
• Pressing @ decreases the right channel
output (from "L-21" to "R-21").
• Pressing # decreases the left channel
output (from "R-21" to "L-21").

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
"SUBWOOFER" appears on the
display.
• Once you have pressed SETTING, MULTI CURSOR % / fi
can be also used for selecting "SUBWOOFER."
• The display changes to show the current setting.
2. Press MULTI CURSOR @ / # to
select "YES" or "NO."
YES: Select this when a subwoofer is used.
NO: Select this when no subwoofer is used.

Changing the Source Name

When you have connected the MD recorder to the TAPE/MD jacks
or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name shown on the display when you select the
MD recorder or the DBS tuner as the source.
On the front panel ONLY:
When changing the source name from "TAPE" to "MD":
1. Press TAPE/MD.
• Make sure "TAPE" appears on the display.
2. Press and hold SOURCE NAME
(TAPE/MD) until "ASSGN. MD"
appears on the display.
To change the source name from "MD" to "TAPE," repeat
the same procedure above (in step 1, make sure
on the display
When changing the source name from "TV SOUND" to "DBS":
1. Press TV SOUND/DBS.
• Make sure "TV SOUND" appears on the
ADJUST display.
2. Press and hold SOURCE NAME
(TV SOUND/DBS) until "ASSGN.
DBS" appears on the display.
To change the source name from "DBS" to "TV SOUND,"
MULTI CURSOR
repeat the same procedure above (in step 1, make sure
appears on the display
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
– "TAPE" or "TV SOUND" will appear on the display when you select
the MD recorder or DBS tuner.
– You cannot select the digital input (see page 14) for the MD
recorder and the DBS tuner.
– You cannot use the COMPU LINK remote control system (see page
26) to operate the MD recorder.
SETTING
MULTI CURSOR
).
).
TAPE/MD
SOURCE NAME
"MD" appears
TV SOUND/DBS
SOURCE NAME
"DBS"
11