Connection Diagram - Sony XAV-62BT Service Manual

(XAV-622: E (PAL) and Saudi Arabia models)
Equipment used in illustrations (not supplied)
Front speaker
iPod
Rear speaker
Rear view camera
Power amplifier
Monitor
Active subwoofer
* 1
Cautions
Run all ground (earth) leads to a common ground
(earth) point.
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not disassemble or modify the unit.
Do not install in locations which interfere with airbag
operation.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Do not press on the LCD when installing the unit.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage
rating.
If no car circuits are rated high enough, connect the
unit directly to the battery.
Connection example
Notes ( - A )
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note ( - B )
You cannot use multiple auxiliary devices simultaneously, even if they
are connected to different terminals.
A
FRONT AUDIO
OUT
REAR VIDEO
OUT
ANT REM
Max. supply current: 0.1 A
AMP REM
Max. supply current: 0.3 A
ATT
REVERSE IN
* 1
* 1
REAR
CAMERA
VIDEO
IN
OUT
EXT
REAR/SUB
AUDIO OUT REAR/SUB
AUDIO OUT
AUX
AUDIO IN
From car antenna (aerial)
FRONT
AUDIO OUT
Fuse (10 A)
* 1

Connection diagram

To a common ground (earth) point
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
To the power antenna (aerial) control lead or the
power supply lead of the antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see "Notes on the control and power supply leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To the interface cable of a car telephone
To a car's illumination signal
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
To the +12 V power terminal which is energized
when the ignition switch is set to the accessory
position
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see "Notes on the control and power supply leads."
To the +12 V power terminal which is energized
at all times
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
To the parking brake switch cord
XAV-62BT/622/E62BT/E622
REAR/SUB
AUDIO OUT
Black Orange/white striped
Blue Red
Blue/white striped Yellow
Light blue Light green
White
White/black striped
* 2
Protective device
Gray
Gray/black striped
Green
Green/black striped
Purple
AUX
VIDEO IN
Purple/black striped
3
REMOTE IN*
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA cord (not supplied) to connect auxiliary devices.
To the +12 V power terminal of the car's rear lamp
lead (only when connecting the rear view camera)
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V DC when
you turn on the tuner.
If your car has a built-in FM/AM antenna (aerial) in the rear/side glass,
connect the power antenna (aerial) control lead (blue) or the accessory
power supply lead (red) to the power terminal of the antenna (aerial)
booster. For details, consult your car dealer.
A power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power will always be
supplied to the memory circuit even when the ignition switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with adequate
power handling capacities to avoid damage.
Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
Do not connect the ground (earth) lead of this unit to the negative (–)
terminal of a speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (–) lead for the right and left
speakers.
Do not connect the unit's speaker leads to each other.
Notes on connection
If "Output connection failure." appears in the display, make sure the
speaker and amplifier are connected correctly.
To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).
B
REAR AUX
AUDIO IN
CAMERA IN
Video camera*
REAR AUX
VIDEO IN
* not supplied
RC-202IPV*
*
1 RCA pin cord (not supplied)
*
2
ILLUMINATION Do not remove the protective device.
* 3
A separate adaptor may be required.
* 4
For details on connecting to the
parking brake switch cord, see
"Connecting the parking brake lead
( )" on the reverse side.
* 5
Speaker impedance: 4 – 8 ohms × 4
PARKING BRAKE
* 4
Left
Right
* 5
Left
Right
13