Advertisement
Disassembly/Assembly Instructions
4. Install the 53191 Ring Gear over the planetary carrier so that the set screw and grease fitting notches will orient correctly once placed into the 53185/55030 Cover.
5. Press the rear 02552 Bearing onto the rear of the planetary carrier until it touches the ring gear. Important: The fit must be snug between the bearings and the ring gear.
However, if its' too tight the planetary carrier will not turn freely. In that case the fit must be loosened so that the planetary carrier will turn freely while still
maintaining a snug fit.
6. Install the 55031 Felt Seal into the 53185/55030/55029 Cover.
7. Install the planetary carrier assembly(ies) into the 53185/55030 Cover so that the notches in the ring gear(s) align with the set screw and grease fitting openings in the
cover. Important: For model 53090 and 53091 be certain to install the 53188 Spacer between the planetary carrier assemblies.
8. Apply a small amount of Loctite #567 (or equivalent) to the threads of the 04114 Set Screw(s) and install into the 53185/55030 Cover.
9. Lubricate the planetary gears through the grease fitting(s) applying 1 plunge at intervals of every 50 hours of use. Order and use the recommended Dynabrade 95542
Grease Gun to insure the maximum gear life.
Tool Assembly:
1. Carefully secure the housing in a vise so that the motor opening is facing up. To avoid damaging the housing do not over tighten the vise.
2. Install the air motor assembly into the housing.
3. Carefully align the cover and the planetary gear assembly(ies) to the housing and the air motor assembly. (Left Hand Thread), (Torque to 28 N•m/250 in.-lbs.).
4. Use the 96034 12mm Hex Key to install the 57066 Muffler Body into the housing. Place the 56027 Muffler Insert into the 56028 Muffler Cap and install these onto
the muffler body.
5. Install the drill chuck and the 53153 Side handle.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool
should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed.
Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
96047 Motor Tune-Up Kit
•
Includes assorted parts to help
maintain and repair motor.
Dynaswivel
®
•
Swivels 360° at two locations which allows an
air hose to drop straight to the floor, no matter
how the tool is held.
•
94300 1/4" NPT.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keep pneumatic tools operating longer
with greater power and less down time.
95842: 1 pt. (473 ml)
95843: 1 gal. (3.8 L)
96034 12mm Hex Key
•
This is used for the removal and
installation of the 57066 Muffler Body.
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
© DYNABRADE, INC., 2012
Accessories
Grease
•
•
•
96213 Bearing Removal Tool
96214 Bearing Removal Tool
•
96240 Bearing Press Tool
96244 Bearing Press Tool
•
96346 Bearing Separator 2 in.
•
Email: Customer.Service@Dynabrade.com
PRINTED IN USA
(continued)
Multi-purpose grease for all types of bearings, cams, gears.
High film strength; excellent resistance to water, steam, etc.
Workable range 0˚ F to 300˚ F.
95541: Push-type Grease Gun (one-handed operation).
95542: 10 oz. (283.5 g) tube.
This tool is designed to pass through the I.D.of the bearing
plate and push against the I.D. of the bearing.
Use with (#2) arbor press to achieve accurate
press of bearings and motor parts.
This is used to remove bearings,
gears, and other components.
DYNABRADE
®
PD12.14_04/12
Advertisement
