Advertisement
Quick Links
Model:
53060 - 3/8" Drill Chuck, 3,400 RPM
53090 - 1/2" Drill Chuck, 950 RPM
53091 - 3/8" Drill Chuck, 950 RPM
53095 - 3/8" Drill Chuck, 4,500 RPM
53096 - 3/8" Drill Chuck, 20,000 RPM
Index Key
No. Part # Description
1 53033 3/8" Drill Chuck 1/2"-20
(Includes Chuck Key)
53034 1/2" Drill Chuck 1/2"-20
(Includes Chuck Key)
53087 3/8" Drill Chuck 3/8"-24
(Includes Chuck Key)
2 55031 Felt Seal
3 04014 Set Screw (2) - 53090/53091
(1) - 53060/53095
4 53185 Cover - 53090/53091
55030 Cover - 53060/53095
55029 Cover - 53096
5 01041 Grease Fitting (2) - 53090/53091
(1) - 53060/53095
6 04114 Spindle Nut
55038 Spindle Nut - 53096
7 02552 Bearing (4) - 53090/53091
(2) - 53060/53095
8 53165 Planetary Carrier
9 53195 Gear (4) - 53090/53091
(2) - 53095
53193 Gear (2) - 53060
10 04026 Bearing (8) - 53090/53091
(4) - 53060/53095
11 53182 Gear Shaft (4) - 53090/53091
(2) - 53060/53095
12 53191 Ring Gear (2) - 53090/53091
(1) - 53060/53095
13 53188 Spacer - 53090/53091
14 53164 Planetary Carrier- 53090/53091
15 01007 Bearing
16 01293 Shim - .001" (.03 mm) THK.
01294 Shim - .002" (.06 mm) THK.
17 53183 Front Bearing Plate
55026 Front Bearing Plate - 53096
18 01010 Spacer
19 01028 Cylinder
20 50767 Pin
21 04017 Rotor - 53060
04009 Rotor - 53090/53091/53095
55025 Rotor - 53096
22 01185 Vane (4/pkg.)
23 55027 Rear Bearing Plate
01743 Rear Bearing Plate - 53096
24 02649 Bearing
25 53163 Handle Assembly
26 55048 Housing - 53060
53066 Housing - 53090
53118 Housing - 53091
53067 Housing - 53095
53119 Housing - 53096
27 96025 Pin
28 55024 Grip
29 56023 Inlet Bushing
30 56027 Muffler Insert (2)
31 69359 Muffler Body
32 69272 Muffler Assembly
33 50936 Pin
34 55035 Trigger
35 55043 Trigger post
36 55052 Valve Stem
37 96069 Spring
38 55039 Bushing
39 50939 O-Ring
40 02027 O-Ring (2)
41 55051 Valve Stop (2)
42 55041 Valve
43 55058 Trigger Assembly
44 53199 Collar
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air
tools (ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabradeʼs
Warning/Safety Operating Instructions for more complete safety information.
1
2
44
A
3
8
T
28 N•m
2
4
T
17 N•m
6
13
18
15
16
17
35
36
A
33
34
O
Oil: O
= Air Lube
1
A
Adhesive: A
= Loctite #609
1
A
= Loctite #271
2
A
= Loctite #380
6
A
= Loctite #567
8
T
Torque: N•m x 8.85 = In. - lbs.
G
Grease: G
= Lubriplate 630 AA
1
Pistol Grip Drill
T
28 N•m
5
G
7
4
1
6
T
17 N•m
7
14
9
10
11
G
1
O
20
22
1
19
21
37
39
41
38
40
42
1
43
KEY
See inside for Important Operating, Maintenance and Safety Instructions.
Parts Page Reorder No. PD12•14
Effective April, 2012
Supersedes PD04•44R
Air Machine and Motor Parts
8
9
G
11
12
1
10
G
1
12
7
Left Hand Threads
23
24
27
28
A
41
1
32
7
25
26
A
6
Apply To Grip
A
2
29
O
1
T
23 N•m
30
31
Advertisement
Related Manuals for Dynabrade 53060
Summary of Contents for Dynabrade 53060
- Page 1 53096 - 3/8" Drill Chuck, 20,000 RPM Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabradeʼs Warning/Safety Operating Instructions for more complete safety information.
-
Page 2: Operating Instructions
2. Some silencers on air tools may clog with use. Clean and replace as required. 3. All Dynabrade rotary vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). -
Page 3: Tool Disassembly
5. Apply Dynabrade Air Lube 95842 to the 01185 Blades and install these into the rotor slot. 6. Install the 01028 Cylinder so that the air inlet area lines up with the air inlet holes in the rear bearing plate. -
Page 4: Tool Assembly
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed.