1. Manuals
  2. Brands
  3. ECH2O Tec. Manuals
  4. Water Filtration Systems
  5. 200-AMS-1
  6. Owner's manual

ECH2O Tec. 200-AMS-1 Owner's Manual

Modular series (230v ac 50hz) watermakers
Hide thumbs
Table of Contents

Advertisement

Quick Links

E E E E
MODULAR SERIES (230V AC 50Hz)
200-AMS-1 / 400-AMS-2 / 500-AML-1
600-AMS-3 / 800-AMS-4 / 900-AML-2
PAGE
2
INTRODUCTION
3
SPECIFICATIONS
4-5
STANDARD SYSTEM FEATURES, OPTIONS AND ACCESSORIES
6
FLOW DIAGRAM
7-9
INSTALLATION INSTRUCTIONS
10
INSTALLATION INSTRUCTIONS OPTIONS
11-12
SYSTEM OPERATION, SHUT DOWN AND FLUSH PROCEDURE
13
MEMBRANE CLEANING PROCEDURE
14
MAINTENANCE TIMETABLE
15
TROUBLESHOOTING GUIDE
16-18
HIGH PRESSURE PUMP REPAIR INSTRUCTION
19-20
WARRANTY
C C C C H H H H
Watermakers
1200-AML-3 / 1500-AML-4
OWNERS MANUAL
O Tec.
O Tec.
O Tec.
O Tec.
2 2 2 2
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 200-AMS-1 and is the answer not in the manual?

Questions and answers

Related Manuals for ECH2O Tec. 200-AMS-1

Summary of Contents for ECH2O Tec. 200-AMS-1

  • Page 1 O Tec. O Tec. O Tec. O Tec. 2 2 2 2 Watermakers MODULAR SERIES (230V AC 50Hz) 200-AMS-1 / 400-AMS-2 / 500-AML-1 600-AMS-3 / 800-AMS-4 / 900-AML-2 1200-AML-3 / 1500-AML-4 OWNERS MANUAL PAGE INTRODUCTION SPECIFICATIONS STANDARD SYSTEM FEATURES, OPTIONS AND ACCESSORIES...
  • Page 2 INTRODUCTION Thank you for choosing an ECH O Tec. reverse osmosis watermaker. We trust that you will be completely satisfied with our product. O Tec Watermakers are manufactured by Echo-Marine as a result of many years of experience installing, servicing and modifying all brands of watermakers. Only highest quality components that have proven to withstand continuous duty in a harsh marine environment are selected for ultimate reliability and lifetime.
  • Page 3 SPECIFICATIONS (AC VERSION 50Hz) RATED PERFORMANCE: 8 gallons / 30ltr. / hour O Tec. 200 – AMS – 1 400 – AMS – 2 16 gallons / 60ltr. / hour 500 – AML – 1 20 gallons / 76ltr. / hour 600 –...
  • Page 4 STANDARD SYSTEM FEATURES 1 PVC sea strainer 2 3/4” barbed hose connectors straight 1 Filter housing with 20 micron pre filter cartridge 1 316 Bracket with 8 screws. 1 20micron cartridge 1 1/2” Service valve with 1 Nylon nipple and 3 barbed hose connectors (with boost pump) or 1 3/4”...

  • Page 5: Available Options And Accessories

    AVAILABLE OPTIONS AND ACCESSORIES If the high pressure pump is installed less than 2 feet below the waterline or an additional 5 micron pre-filter is added, the installation of an optional boost pump is recommended. Boost pump (3/4” intake hose barb, 5/8” outlet hose barb, 4 feet / 1.2 meter 3/4” wire reinforced intake hose, 10 feet / 3 meter 5/8”...
  • Page 6 FLOW DIAGRAM WITH OPTIONS...

  • Page 7: Installation Instructions

    INSTALLATION INSTRUCTIONS HIGH PRESSURE PUMP WITH ELECTRIC MOTOR Mount the high pressure pump/motor unit to a cool location free of vibration. MEMBRANE HOUSING Mount the high-pressure membrane housing(s) with the provided brackets vertical (with the flow upwards) or horizontal in a convenient location away from the heat of the engine as close as possible to the high pressure pump.

  • Page 8: High Pressure Hose

    PRE-FILTER HOUSING Mount the pre-filter in a serviceable location and connect the bottom port of the cleaning / storage valve with the 5/8” reinforced vinyl hose to the bottom intake hose fitting of the high-pressure pump. Secure the hose with hose clamps. If the optional 3/4"...

  • Page 9: Electrical Installation

    PRODUCT WATER TUBING Connect the blue product water tubing or the 1/2" vinyl hose from the center fittings of the membrane housing(s) to the bottom inlet of the flow meter, in the control panel. Connect the tubing or hose from each output port of the 3-way valve to your water tank and to the taste/test station of your choice.
  • Page 10 INSTALLATION INSTRUCTION - OPTIONS BOOST PUMP If the high-pressure pump is installed less than 1 foot below the waterline or an additional 5micron pre- filter is added, the installation of an optional boost pump is recommended. Install the boost pump with the electric motor up or sideways in a dry location (submergible pumps are available) below the water line, in between the sea strainer and the pre-filter(s).

  • Page 11: System Shut Down Procedure

    SYSTEM OPERATION INSTRUCTIONS (AC VERSION) The reverse osmosis membrane contains a preservative solution to prevent microbiological growth. If ingested, may cause irritation of the gastro-intestinal tract, Colic, diarrhea, or other similar symptoms. Therefore, discard all the product water for at least thirty minutes of initial operation, after storage before drinking or before use in food preparations! Do not operate the system using contaminated feed water sources (oil, chlorine or other chemicals).

  • Page 12: Fresh Water Flush Procedure

    FRESH WATER FLUSH PROCEDURE Caution: The fresh water pressure should not exceed the range of the low pressure gauge/s. The installation of a pressure reducer may be necessary. If you don’t use your watermaker for the next three days, you will need to flush your system with fresh water or infuse a biocide solution.

  • Page 13: Membrane Cleaning Procedure

    MEMBRANE CLEANING PROCEDURE The ECHO Tec. Watermaker must be chemically cleaned when the product water output drops by 15% of the specified amount. The frequency of this occurring will vary greatly depending upon feed water. Fouling of the membrane will naturally occur during normal usage of the ECHO Tec. Watermaker.

  • Page 14: Maintenance Timetable

    MAINTENANCE TIMETABLE The following maintenance timetable is an estimate of the time intervals at which maintenance may be required only. This schedule must be adjusted to the regularity of usage, the condition of the intake water, the length of time the system is exposed to seawater and the total running time following each system cleaning.

  • Page 15: Troubleshooting Guide

    HIGH PRESSURE PUMP SYSTEM TROUBLESHOOTING GUIDE CAUSE REMEDY MALFUNCTION The Pressure and/or the product Worn packing seals Replace packing seals amount drops Broken valve spring Replace spring Belt slippage Tighten or replace belt Fouled inlet strainer Clean strainer Fouled pre-filter(s) Replace filter cartridge(s) Cavitation Check suction lines for restrictions...
  • Page 16 HIGH PRESSURE PUMP REPAIR INSTRUCTION SERIES EP-12-34 / EP-14-34 / EP-17-34 Disassembly sequence of the front end of the ECH O Tec. high-pressure pump. Refer to the pump diagram. Remove the three discharge valve plugs and the three inlet valve plugs (32), with a 22 mm socket wrench.
  • Page 17 Should you find it necessary to service the plunger assembly (16), you can do so by removing the tension screw (16D). Inspect all parts and replace as necessary. NOTE: In order to drive the pump from the side opposite the present shaft extension, simply remove the valve casing from the crankcase and rotate the pump 180 degrees to the desired position.

  • Page 19: Warranty

    O TEC. WATERMAKER LIMITED WARRANTY Echo Marine Ltd. warrants to the original purchaser for a period of twenty-four (24) months from the date of shipment that the ECHO Tec. watermaker will perform according to specifications. Echo Marine’s liability under this warranty shall be limited to repair or replacement of the ECHO Tec. watermaker at Echo Marine’s option.
  • Page 20 The ECHO Tec. Membrane Element is guaranteed to be cleanable for a minimum of one year from date of shipment, provided that cleaning instructions are adhered to and foulant is acid soluble metal hydroxides and calcium carbonates or alkaline soluble organic, inorganic substances and microbiological slimes.

This manual is also suitable for:

400-ams-2500-aml-1600-ams-3800-ams-3900-aml-21200-aml-3 ... Show all

Table of Contents