1. Manuals
  2. Brands
  3. ECH2O Tec. Manuals
  4. Water Filtration Systems
  5. 900-BHL- 2
  6. Owner's manual

ECH2O Tec. 900-BHL- 2 Owner's Manual

Beach house series wall mount unit
Hide thumbs Also See for 900-BHL- 2:
Table of Contents

Advertisement

Quick Links

Download this manual
E E E E
C C C C H H H H
Watermakers
900-BHL- 2 / 1200-BHL- 3 / 1500-BHL- 4
PAGE
2
INTRODUCTION
3
SPECIFICATIONS
4
STANDARD SYSTEM FEATURES
5
INSTALLATION LAYOUT
6-7
INSTALLATION INSTRUCTIONS
8-9
OPERATION INSTRUCTIONS
10
MEMBRANE CLEANING PROCEDURE
11
MAINTENANCE TIMETABLE
12
TROUBLESHOOTING GUIDE
13-14
HIGH PRESSURE PUMP REPAIR INSTRUCTIONS
16-17
LIMITED WARRANTY
2 2 2 2
BEACH HOUSE SERIES
(WALL MOUNT UNIT)
OWNERS MANUAL
O Tec.
O Tec.
O Tec.
O Tec.
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 900-BHL- 2 and is the answer not in the manual?

Questions and answers

Related Manuals for ECH2O Tec. 900-BHL- 2

Summary of Contents for ECH2O Tec. 900-BHL- 2

  • Page 1 O Tec. O Tec. O Tec. O Tec. 2 2 2 2 Watermakers BEACH HOUSE SERIES (WALL MOUNT UNIT) 900-BHL- 2 / 1200-BHL- 3 / 1500-BHL- 4 OWNERS MANUAL PAGE INTRODUCTION SPECIFICATIONS STANDARD SYSTEM FEATURES INSTALLATION LAYOUT INSTALLATION INSTRUCTIONS OPERATION INSTRUCTIONS...
  • Page 2 INTRODUCTION Thank you for choosing an ECHO Tec. reverse osmosis desalination system. We trust that you will be completely satisfied with our product. The Beach House Series has been specially designed for small hotels, marinas and beach houses. The high power efficiency and low maintenance cost makes high quality RO water in many cases more economical than land supplied water, if available.
  • Page 3 SPECIFICATIONS RATED PERFORMANCE: min. 20 gallons – 75ltr. / hour ECHO Tec: 500 – BHL – 1 min. 38 gallons – 140ltr. / hour 900 – BHL – 2 min. 50 gallons – 210ltr. / hour 1200 – BHL – 3 1500 –...
  • Page 4 STANDARD SYSTEM FEATURES 1 Seawater feed pump with 3/4” hose barb outlet 1 PVC sea strainer with 3/4” PVC pipe connection 1 Priming reservoir 2 3/4” pipe connections 2 Filter housings with bracket and 5 and 20 micron pre filter cartridges 1 Storage/cleaning valve with 3/4”...

  • Page 6: Installation Instructions

    INSTALLATION INSTRUCTIONS HIGH PRESSURE PUMP UNIT Mount the high pressure pump unit in a cool and dry location, not higher than 30ft above low water level at a distance not further than 100ft / 30m. The electrical installation should only be done by a professional electrician. Check the correct voltage before installing the system.

  • Page 7: High Pressure Hose

    SEAWATER FEED PUMP AND PRIMING RESERVOIR With the aid of the priming reservoir, the feed pump is able to prime the raw water up to a height of 9ft. Mount the feed pump in a dry location not higher than 9ft above low water level. Mount the priming reservoir with the outlet (lower connection) at the same level as the intake of the feed pump in a dark location (inhibits growth of algae).

  • Page 8: System Shut Down Procedure

    SYSTEM OPERATION INSTRUCTIONS The reverse osmosis membrane contains a preservative solution to prevent microbiological growth. If ingested, may cause irritation of the gastro-intestinal tract, colic, diarrhea, or other similar symptoms. Therefore, discard all the product water for at least thirty minutes of initial operation or after storage before drinking or use in food preparations! Do not operate the system using contaminated feed water sources (oil, chlorine or other chemicals).

  • Page 9: Fresh Water Flush Procedure

    FRESH WATER FLUSH PROCEDURE You should fresh water flush your watermaker after every use or infuse a biocide solution for long term storage. The fresh water flush prepares your watermaker for a shut down period of seven days maximum. You can repeat the flush procedure every seven days, to extend the short term storage. Open the pressure control-valve all the way counter-clockwise.

  • Page 10: Membrane Cleaning Procedure

    MEMBRANE CLEANING PROCEDURE The membranes of the ECHO Tec. Watermaker must be chemically cleaned when the product water output drops by 20% of the specified amount. The frequency of this occurring will vary greatly depending upon feed water. Fouling of the membranes will naturally occur during normal usage of the ECHO Tec.

  • Page 11: Maintenance Timetable

    MAINTENANCE TIMETABLE The following maintenance timetable is an estimate of the time intervals at which maintenance may be required only. This schedule must be adjusted to the regularity of usage, the condition of the intake water, the length of time the system is exposed to seawater and the total running time following each system cleaning.
  • Page 12 HIGH PRESSURE PUMP SYSTEM TROUBLESHOOTING GUIDE MALFUNCTION CAUSE REMEDY The pressure Worn packing seals Replace seals drops broken valve spring Replace spring Fouled inlet strainer Clean strainer Fouled pre-filter(s) Replace filter cartridge(s) Cavitation Check suction lines for restrictions Water in crankcase High humidity Reduce oil change interval Worn seals...
  • Page 13 HIGH PRESSURE PUMP REPAIR INSTRUCTION ECHO TEC PUMP SERIES XL-60/2.3, XL-60/3.0 AND XL-60/3.6 ∂ ssembly isAssembly 1.1 - Unscrew head bolts. ∂ Tightening sequence of head bolts, for XT Series and HPE Series, for XR Series and XL Series. 1.2 - Remove the head by rotating the shaft and levering between head and body. 1.3 - For re-assembly: Invert above instructions, and keep to torque rates shown on page 8. nsPecTiOn inleT OuTleT vAlves 2.1 - Remove valve caps, slide out inlet/outlet valves check the sondition of the various components of the...
  • Page 14 3.2 - Disassemble the components of the piston guide, checking the condition, replace if necessary. 3.3 - For re-assembly: Invert operation. ePlAcing The PisTOns 4.1 - Remove the head (See ∂), then unscrew the piston retainers. 4.2 - Slide off the ceramic pstions, check their condition, and replace if necessary. 4.3 - For re-asembly: Invert above operations. Keep to torque rating and shown on page 8. Be careful not to ePlAcing Oil seAls scratch piston guide! 6.1 - Remove the head (See ∂), • remove the ceramic pistons • discharge oil 6.2 - Remove the oil seals and the O-Rings, checking the seats and the piston guides. 6.3 - Remove the rear cover gasket. 6.4 - For re-assembly: Invert above operations. Keep to torque ratings as shown on page 8. RAnk mechAism mAinTenAnce 7.1 - Remove the head (See ∂), • remove the ceramic pistons • discharge oil 7.2 - Remove the rear cover. 7.3 - Remove the con-rod sliding the one piece-rod whilst removing the shaft. 7.4 - For re-assembly: Invert above operations. Replace the oil seals!
  • Page 15 ECHO TEC. WATERMAKER LIMITED WARRANTY Echo Marine Ltd. warrants to the original purchaser for a period of twelve (12) months from the date of shipment that the ECHO Tec. watermaker will perform according to specifications. Echo Marine’s liability under this warranty shall be limited to repair or replacement of the ECHO Tec. watermaker at Echo Marine’s option.
  • Page 16 The ECHO Tec. Membrane Element is guaranteed to be cleanable for a minimum of one year from date of shipment, or commissioning of the system by Echo Marine Ltd, provided that cleaning instructions are adhered to and foulant is acid soluble metal hydroxides and calcium carbonates or alkaline soluble organic, inorganic substances and microbiological slimes.

This manual is also suitable for:

1200-bhl- 31500-bhl- 4

Table of Contents