Sony RDR-GX210 Service Manual page 11

QQ
3 7 63 1515 0
Controlling the volume of your AV
amplifier (receiver) with the remote
1 2 3
Number
4 5 6
buttons
7 8 9
0
1
Slide the TV/DVD switch to DVD.
2
Hold down [/1, and enter the
manufacturer code (see the table below)
for your AV amplifier (receiver) using the
number buttons.
3
Release [/1.
The 2 (volume) +/– buttons control the AV
amplifier's volume.
If you want to control the TV's volume, slide
the TV/DVD switch to TV.
z Hint
If you want to control the TV's volume even when the
TV/DVD switch is set to DVD, repeat the steps above
and enter the code number 90 (default).
Code numbers of controllable AV amplifiers
(receivers)
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your AV amplifier (receiver).
Manufacturer Code number
Sony 78, 79, 80, 91
Denon 84, 85, 86
Kenwood 92, 93
Onkyo 81, 82, 83
Pioneer 99
Sansui 87
Technics 97, 98
Yamaha 94, 95, 96
TE
L 13942296513
20
Language
OSD
Menu
Audio
Subtitle
3
Press M/m to select a language, and press
ENTER.
The on-screen language changes to the
selected language.
4
Press < to return to the Setup Display,
and follow the steps of "Setting the clock"
(see below).
Setting the clock
1
Press M/m to select
press ,.
[Settings] Setup appears.
2
Press M/m to select [Clock], and check
that the clock is correctly set.
Settings
Auto Preset
Channel Settings
Clock
TV Aspect
Display Mode
Line1 Decoder
Progressive Mode
PBC
Factory Setup
If incorrect, set the clock manually (page 72).
Or, the timer recording does not work
www
properly.
3
Follow the steps of "Setting the aspect
ratio for the connected TV" (see below).
.
22
http://www.xiaoyu163.com
If you have a Sony DVD player or
more than one Sony DVD recorder
If the supplied remote interferes with your other
TV/DVD
Sony DVD recorder or player, set the command
switch
mode number for this recorder and the supplied
"/1
remote to one that differs from the other Sony
DVD recorder or player.
The default command mode setting for this
recorder and the supplied remote is "MODE3."
2 +/–
1
Turn off the recorder.
2
Press down x (stop) on the recorder until
"MODE" appears in the front panel
display.
3
While keeping x (stop) pressed,
repeatedly press ./> on the
recorder to select the command mode
(MODE1, 2, or 3).
Front panel display
4
Slide the COMMAND MODE switch on the
remote so it matches the mode you
selected above.
Setting the aspect ratio for the
connected TV
English
Deutsch
1
Press M/m to select [TV Aspect], and press
Italiano
Español
,.
Português
Settings
Auto Preset
Channel Settings
Clock
TV Aspect
Display Mode
Line1 Decoder
Progressive Mode
PBC
Factory Setup
2
Press M/m to select the aspect ratio of the
connected TV, and press ENTER.
[4:3]: For a standard 4:3 screen TV without a
wide screen mode. Select [Display Mode] in
[Settings] Setup.
[Settings], and
[16:9]: For a wide-screen TV or standard TV
with a wide screen mode.
3
Press SET UP to turn off the Setup Display.
See "Additional settings" below and make
other adjustments accordingly.
Additional settings
Depending on the connected equipment, the
following adjustments may be necessary.
Auto Adjust On
◆If you connect a TV that accepts progressive
Auto Adjust Off
625p format signals to the COMPONENT VIDEO
Date 12 / 04
OUT jacks
Year 2005
Set [Progressive Mode] in [Settings] Setup to [On]
Time 12 : 00
(page 73).
◆If you connect an AV amplifier (receiver) with a
Dolby Digital, DTS, or MPEG audio decoder
Make necessary settings in [Audio] Setup
(page 74).
You can make other adjustments using the Setup
x ao
y
Displays, such as picture, sound, and subtitle
languages. (See "Settings and Adjustments" on
page 69.)
i
http://www.xiaoyu163.com
8
Step 7: Initial Setup
Use the Setup Displays to make the initial settings
for using the recorder. Complete the initial setup
in the following order.
Tuner and Channel Setup
m
OSD Language Setup
m
x
Clock Setup
m
TV Type Setup
m
./>
Audio and Video connection Setup (if necessary)
Follow the steps from "Presetting channels" to
"Additional settings" below.
COMMAND
MODE switch
1
4
7
SET UP
Presetting channels
1
Turn on the TV.
2
Press [/1.
3
Switch the input selector on your TV so that
the signal from the recorder appears on
your TV screen.
Q Q
3 6 7 1 3
Connecting a VCR or Similar Device
After disconnecting the recorder's mains lead from the mains, connect a VCR or similar recording device
to the LINE IN jacks of this recorder.
Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack) (page 66).
See also the operating instructions supplied with the connected equipment.
To record on this recorder, see "Recording From Connected Equipment" (page 45).
Connecting to the LINE 3 jack
4:3
Connect a VCR or similar recording device to the LINE 3/DECODER jack of this recorder.
16:9
to SCART input
Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen.
DVD recorder
Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes,
watch the tapes through a second line input on your TV.
VCR DVD recorder
u163
• When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the TV/DVD
button on the remote.
• If you disconnect the recorder's mains lead, you will not be able to view the signals from the connected VCR.
.
1-5
2 9 9 4 2 8
4
Press SET UP.
The Setup Display appears, which allows you
to make adjustments to the recorder. For
details about the Setup Display, see page 69.
Settings
Auto Preset
Channel Settings
Clock
TV Aspect
Display Mode
Line1 Decoder
Progressive Mode
PBC
Factory Setup
5
Press ENTER while [Start] is selected.
The recorder automatically starts searching
for all of the receivable channels and presets
them.
Settings
Auto Preset
Channel Settings
"/1
Clock
TV Aspect
Display Mode
2 3
Line1 Decoder
5 6
Progressive Mode
8 9
PBC
0
Factory Setup
To manually set, disable, or fine-tune the
channels, see "[Channel Settings]" in
[Settings] Setup (page 70).
</M/m/,,
6
ENTER
Press < to return to the Setup Display,
and follow the steps of "Selecting a
language for the on-screen display" (see
below).
If you do not want to change the on-screen
display language, go to "Setting the clock"
(page 22).
Selecting a language for the on-
screen display
1
Press M/m to select
(language), and press ,.
[Language] Setup appears.
2
Press M/m to select [OSD] (on-screen
display), and press ,.
1 5 0 5 8 2 9 9 4
TV
SCART cord
(not supplied)
to i to i LINE
LINE1-TV 3/DECODER
AERIAL LINE 3 / DECODER DIGITAL OUT COMPONENT LINE 2 OUT LINE 4 IN
VIDEO OUT
COAXIAL
IN
PCM/DTS/
MPEG/
DOLBY DIGITAL L L
P /C B B AUDIO AUDIO
VIDEO OUT
LINE 2 OUT DIGITAL OUT
LINE 1 - TV SELECT
RGB R R
P R /C R
PCM/DTS/MPEG/
OUT
DOLBY DIGITAL
OPTICAL
COMPO-
NENT Y VIDEO VIDEO
S VIDEO
VCR TV
Line input 1
m
TV
Line input 2
co
9 9
Start
Stop
Searching 11%
[Language]
2 8 9 9
, continued
21
VCR
DVD recorder
, continued
23