Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BCS SD03 speed dome 66
Summary of Contents for BCS SD03 speed dome 66
- Page 1 Speed Dome 66 Installation Manual...
-
Page 2: Table Of Contents
Table of Contents INSTALLATION....................6 Installation Preparation ......................... 6 Installation Mode............................ 6 1.2.1 Speed Dome Installation Mode....................... 6 1.2.2 Bracket Installation Mode ........................ 7 SPEED DOME INSTALLATION................9 General Introduction..........................9 Hanging Bracket Speed Dome Installation ..................9 2.2.1 Installation Requirement ........................9 2.2.2 Hanging Bracket Installation ...................... - Page 3 Welcome Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product!
-
Page 4: Important Safeguards And Warnings
Important Safeguards and Warnings Safety Measures Qualified Engineer Needed The installation engineer or maintenance engineer shall have corresponding CCTV system installation certificate or maintenance qualification certificate. The installation engineer or maintenance engineer shall have qualification certificate for work at height. The installation engineer or maintenance engineer shall have the basic knowledge and operation technique for low-voltage cable layout and low-voltage electronic cable connection. - Page 5 Do not try to dismantle or modify the device There is risk of personal injury or device damage resulting from opening the shell. Please contact your local retailer if there is internal setup or maintenance requirement. We are not liable for any problems caused by unauthorized modifications or attempted repair.
-
Page 6: Installation
1 INSTALLATION 1.1 Installation Preparation Basic Requirement All installation and operation here should conform to your local electrical safety codes. Before installation, please open the package and check all the components are included. Please make sure the speed dome installation environment and installation mode can meet your requirement. -
Page 7: Bracket Installation Mode
Embedded installation In-ceiling installation Bracket installation 1.2.2 Bracket Installation Mode The bracket installation consists of the following modes: Hanging installation Corner installation Pole installation Suspended installation The bracket installation is suitable for indoor and outdoor environment. The outdoor speed dome has a sun-shade cover and it also has an internal heater device. The outdoor speed dome IP standard is IP 66. - Page 8 Figure 1-2 1.2.2.3 Pole Installation Pole installation is suitable for indoor and outdoor hard pole structure. See Figure 1-3. Please refer to chapter 2.4 for detailed information. Figure 1-3 1.2.2.4 Suspended Installation The suspended installation has the following two types. Please refer to chapter 2.5 for detailed information.
-
Page 9: Speed Dome Installation
2 SPEED DOME INSTALLATION 2.1 General Introduction Speed dome consists of the following components. See Figure 2-1. Speed Dome Cover Component Body Compon External Cover Component Figure 2-1 2.2 Hanging Bracket Speed Dome Installation 2.2.1 Installation Requirement The hanging bracket is suitable for indoor or outdoor hard wall structure. The wall thickness shall support the expansion bolt. - Page 10 Figure 2-2 You can use socket head cap screw to fix hanging bracket and external cover component. (Please install waterproof sealing cushion) socket head cap screw M5×12 External Cover Component Hanging Bracket Figure 2-3 After you installed bracket and external cover components, loosen captive screws and open the panel.
-
Page 11: Camera Installation
Figure 2-4 Then please follow Figure 2-5 to insert the power pin, video/control pin, alarm cable pin to the corresponding sockets in the outlet. Note: Please make sure the power is disconnected when you connect the power cable. After you connected the cable to the power, please check LED light in the power panel is on or not. - Page 12 Please use your hand to hold the camera and then adjust the lock tab between the camera and the panel. 1— Captive screw and semi-circle groove. 2— AMP socket connector 3/4/5- three pilot spool You can refer to Figure 2-7 for detailed information. Now please turn the camera in the lock direction until the lock tab of the camera fixing bracket meets the lock line of the camera.
-
Page 13: Corner Bracket Speed Dome Installation
Cable Heating Strip Steel Safety Rope Figure 2-8 Please refer to Figure 2-9 to install bottom cover. Please line the two round grooves of bottom cover side to the two captive screws on the bottom cover side. The angel shall ranges from -5 degrees to +5 degrees. Then you can push the bottom cover up and fix the captive screws. - Page 14 Figure 2-10 Pull the power cable, video/control, alarm cable through the bottom central hole, waterproof grew and bracket central hole. Please reserve the enough cable length and then use M8 expansion blot to fix the corner bracket pedestal in the wall. See Figure 2-11.
-
Page 15: Pole Bracket Speed Dome Installation
Bottom cover connection: Please refer to Figure 2-8. Camera installation: Please refer to Figure 2-7. Bottom cover installation: Please refer to Figure 2-9. After you completed the above steps, the corner installation is shown as in Figure 2-13. Figure 2-13 2.4 Pole Bracket Speed Dome Installation 2.4.1 Installation Requirement The pole installation speed dome is suitable for indoor or outdoor hard structure pole... -
Page 16: Pole Bracket Installation
2.4.2 Pole Bracket Installation Please refer to Figure 2-15 to install clamp and pole bracket. Pull the cable out of the pole accessories and then use clamp to fix the pole accessories to the pole. Finally, you can use glass cement to the output hole to secure waterproof. -
Page 17: Suspended Bracket Speed Dome Installation
Figure 2-17 2.5 Suspended Bracket Speed Dome Installation 2.5.1 Installation Requirement Suspended bracket speed dome installation is suitable for indoor or outdoor hard structure ceiling. The ceiling thickness can install expansion bolt. The ceiling shall support the 4x speed dome weight. 2.5.2 Accessories Installation The installation accessories are shown as in Figure 2-18. - Page 18 Without wire slot With wire slot Figure 2-19 Loosen the M4 bolt in the flanges side. Separate the connection flange and pole and then pull the power, video/control, alarm cable out of the seal groove of flanges bottom side, and then lead them through the flanges central hole. Now you can fix the flange in the ceiling.
- Page 19 Teflon tape M4 Screw Silica gel Figure 2-21 Please loosen the M4 bolt at the splicing sleeve of pole bottom (just a little will be O.K), then turn the screw thread of the upper cover splicing sleeve in. Now pull the power cable through the upper cover and then turn the upper cover to the pole splicing sleeve firmly.
- Page 20 Camera installation: Please refer to Figure 2-7. Bottom cover installation. Please refer to Figure 2-9.
- Page 21 3 Protocol, Baud Rate, Address setup Before you operate, you need to set protocol, baud rate and address. Otherwise you can not control the product! 3.1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome: Protocol Baud rate Address...
-
Page 22: Set Address Dial Switch
9600bps 4800bps 2400bps 1200bps Please refer to the parity setup sheet for detailed information. Parity NONE EVEN NONE 3.2 Set address dial switch The encode mode adopts binary system. 1 to 8 is valid bit. The highest address bit is 255. -
Page 23: Cable Connection
4 Cable Connection RS485 and Power Cable Connection There are three cable groups: power cable, RS 485 and video cable. Draw out the cables from the dome to connect with main control devices (such as monitor, control keyboard, DVR and etc.) and power adapter. See Figure 3-1 and Figure 3-2. Figure 4-1 Figure 4-2 Name... - Page 24 Figure 4-3 Name Function AC24V 24V power port. Connect to the power cable. EARTH Ground port. AC24V 24V power port. Connect to power cable. Extension RS 485 port is shown as in Figure 3-4. Figure 4-4 Name Function ＋ Extension peripheral 485 port. Such as control temperature, humidity sensor.
- Page 25 Name Function Alarm out：1-2 Two alarm output channels. When there is an alarm from current channel, system activates relay or not. Alarm output relay default setup is NO. You can use the jump-cap near the power board relay to set. NO：Normal open alarm output.
Need help?
Do you have a question about the SD03 speed dome 66 and is the answer not in the manual?
Questions and answers