PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE 3-4-1. Set up mode for White Balance Adjustment ... THESE COMPONENTS WITH SONY PARTS WHOSE PART 3-4-2. White Balance of colour temperature “High” .. NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
Page 4
WAX2 RM-ED005 . s l . s l . s l e i l . s l i g i i n i i n i - 4 -...
Page 5
WAX2 RM-ED005 KDL-26S2000E KDL-26S2000U KDL-26S2010E KDL-26S2010U Model Name KDL-32S2000E KDL-32S2000U KDL-32S2010E KDL-32S2010U KDL-26S2020E KDL-26S2020U Item KDL-40S2000E KDL-40S2000U KDL-40S2010E KDL-40S2010U KDL-32S2020E KDL-32S2020U KDL-46S2000E KDL-46S2000U KDL-46S2010E KDL-46S2010U RGB Priority Sub Woofer Scart 1 Scart 2 Front in (5) Projector Norm B/G Norm I...
Page 6
WAX2 RM-ED005 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
WAX2 RM-ED005 WAX2 SELF DIAGNOSTIC SOFTWARE The identification of errors within the WAX2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
Page 8
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. 3: Bundling the cables 5: Selecting the language and country/ 1: Checking the 2: Connecting an aerial/ region accessories Connecting an aerial only...
Page 9
Press to select the language Before you start auto-tuning the TV, insert displayed on the menu screens, then press a pre-recorded tape into the VCR connected to the TV (page 4) and start play back. The video channel will be located and stored on Watching TV Press the number buttons or PROG +/- to the TV during auto-tuning.
Page 10
Using the Tools menu Checking the Digital Electronic Programme Guide Viewing pictures from Press TOOLS to display the following options when viewing pictures from connected equipment other (EPG) connected equipment than PC. Options Description In digital mode, press to display the Power Saving See page 27.
Picture menu Navigating through menus You can select the options listed below on the Picture “MENU” allows you to enjoy various convenient features of this TV. You can easily select channels or external menu. To select options in “Settings”, see “Navigating inputs with the remote.
Sound menu Screen menu You can select the options listed below on the Sound You can select the options listed below on the Screen menu. To select options in “Settings”, see “Navigating menu. To select options in “Settings”, see “Navigating through menus”...
Set-up menu PC Settings menu You can select the options listed below on the Set-up You can select the options listed below on the PC menu. To select options in “Settings”, see “Navigating Settings menu. To select options in “Settings”, see through menus”...
Page 14
Analogue Set-up menu (Analogue mode only) Digital Set-up menu You can change/set the analogue settings using the You can change/set the digital settings using the Analogue Set-up menu. To select options in Digital Set-up menu. To select options in “Settings”, “Settings”, see “Navigating through menus”...
Connecting to the TV (rear) To connect Do this PC D Connecting optional equipment Connect to the PC sockets. It is recommended to use a PC cable with ferrites. You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied. Digital satellite Connect to the HDMI IN 4 socket receiver or DVD...
Sound Output Optional Accessories Additional Information 10 W + 10 W • Wall-Mount Bracket SU-WL51 (for KDL-46S2000/KDL-46S2010/ Supplied Accessories KDL-40S2000/KDL-40S2010) Specifications Colour/Video System Refer to “1: Checking the accessories” on page 4. SU-WL31 (for KDL-32S2000/KDL-32S2010/ Analogue: PAL, SECAM KDL-26S2000/KDL-26S2010) NTSC 3.58, 4.43 (only Video In) Display Unit Design and specifications are subject to change Digital:...
For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. Channels Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval). Problem Cause/Remedy...
WAX2 RM-ED005 SECTION 3 SET-UP ADJUSTMENTS 3-2. Signal Level Adjustment 3-1. How to enter Service Mode Service adjustments to this model can be performed using the 3-2-1. Set up of AD calibration1 adjustment for supplied remote Commander RM-ED005. terrestrial analog. The following adjustments are done via ECS.
WAX2 RM-ED005 3-2-4. C signal calibration1 adjustment for 3-2-7. Set up of C signal calibration1 adjustment terrestrial analog. for video. 1. Send ECS_ADJUST_TCD3_HUE_RF command. 1. Input PAL colour bar 75%Y, 75%C via AV1 input. 2. Read S-REG: READ_BACK_B00 via ECS. (READ_AREA=0). 2.
WAX2 RM-ED005 2. Send ECS_ADJUST_TCD3_CONT_V command. 3-3-2. Set up Trident internal SG and brightness 3. Read the value of S-REG:APL_LUMA via ECS. Confirming that measurement the value is within spec of the table below. 1. Ensure TEST_PATTEN_ON=1. 2. Ensure TEST_G_LEVEL=204. 3.
Page 28
WAX2 RM-ED005 6. Adjust R_GAMMA_OFST_01 and B_GAMMA_OFST_01 10. Adjust R_GAMMA_OFST_03 and B_GAMMA_OFST_03 chroma values so that they are within tolerance in the table below. chroma values so that they are within tolerance in the table below. Tolerance Tolerance 20IRE 0.263 0.274 0.5JND(*1) 20IRE...
WAX2 RM-ED005 3-5. Panel Replacement COLOR_TEMP=1 When replacing the panel please reset the gamma and white balance R_DRV B_DRV R_BKG B_BKG before performing W/B (See page 27) for new panel. 26" 3-6. Board Replacement 32" 3-6-1. AE Board Replacement 40" When replacing the ‘AE’...
Page 41
BE.-WAX2 R1021 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL 1/10W D1_IN_Y Y1/G1 STBY 3.3V R1022 R1040 R1044 RN-CP D1_IN_CB FROM A PWB CB1/B1 R1051 C1030 R1023 1/10W D1_IN_CR AVLINK CR1/R1 D1_IN_L3/MODE L3_1/MODE_1 OUT1 R1042 R1011 D1_IN_SW/FB R1046 N.C./FB_1 R1012 D2_IN_Y...
Page 48
BE.-WAX2 TO F/E POWER(J&U/C) 11/12 CN4701 +10.5V UNREG10.5V R4701 +10.5V C4700 FE5/6.2/10.5V R4715 C4702 C4701 FROM F/E HD VIDEO(DIGITAL) INPUT TO Trident MAIN_DIN SYSTEM(J)/SD_VIDEO(UK) CN4702 DT_C_DY0 DT_C_DY1 DT_C_DY2 DT_C_DY3 SYS/SD_VIDEO CN4700 DTT_BUS_MOSI BUSMOSI U_DIN/DCLK R4702 XX DTT_BUS_MISO DT_C_DY4 BUSMISO R4703 XX DTT_BUS_SCK DT_C_DY5 BUS SCK...
Page 49
BE.-WAX2 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL TUNER_CONTROL CN1702 POWER TO TUNER R1710 1/16W R1723 Q1701 2SC1623-L5L6 UNREG33V FB1711 R1722 R1721 R1708 C1703 3.3K 470K CN1701 R1706 CN1700 D1701 SDA_TUNER C1704 C1708 C1712 R1705 HZU16B2TRF-E +33V 0.001 100PF FB1720...
~ BE Printed Wiring Board Conductor Side A ~ ~ BE Board Semiconductor Location Table Side A ~ ~ BE Board Semiconductor Voltage Table Side A ~ ~ BE Board IC Voltage Table Side A ~ - 50 -...
Page 51
~ BE Printed Wiring Board Conductor Side B ~ ~ BE Board Semiconductor Location Table Side B ~ - 51 -...
Page 57
FEE-WAX2 FB3600 C3608 C3600 C3604 +3V3D NOTE: THESE ARE THE TWO SCREW A SIDE B SIDE CONNECTIONS TO THE GND ISLAND CN3610 +3V3D R3612 R3618 FB3601 NEAR END OF CI CONNECTOR. CN3604 R3613 R3619 THIS ISLAND IS GROUNDED VIA THE R3614 R3620 +3V3D...
~ FEE Printed Wiring Board Conductor Side A ~ ~ FEE Board Semiconductor Location Table Side A ~ ~ FEE Board Semiconductor Voltage Table Side A ~ ~ FEE Board IC Voltage Table Side A ~ ~ FEE Printed Wiring Board Conductor Side B ~ ~ FEE Board Semiconductor Location Table Side B ~ - 58 -...
~ H1E Printed Wiring Board Conductor Side A ~ ~ H1E Printed Wiring Board Conductor Side B ~ ~ H2E Printed Wiring Board Conductor Side A ~ ~ H2E Printed Wiring Board Conductor Side B ~ ~ H3E Printed Wiring Board Conductor Side A ~ ~ H3E Printed Wiring Board Conductor Side B ~ ~ H46E Printed Wiring Board Conductor Side A ~ ~ H46E Printed Wiring Board Conductor Side B ~...
~ TUE Printed Wiring Board Conductor Side A ~ ~ TUE Board Semiconductor Location Table Side A ~ ~ TUE Board Semiconductor Voltage Table Side A ~ ~ TUE Board IC Voltage Table Side A ~ ~ TUE Printed Wiring Board Conductor Side B ~ ~ TUE Board Semiconductor Location Table Side B ~ DIODE TRANSISTOR...
SECTION 5 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these items. with a collation number in the remarks column. 5-1. CHASSIS REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK X-2108-506-2 BEZEL ASSY (26) (26S2000 UK/AEP) 1-802-059-11 LCD PANEL (40S2000/S2010 UK/AEP) X-2109-273-2 BEZEL ASSY (26) (26S2010 UK/AEP) 1-802-100-12 LCD PANEL (46S2000/S2010 UK/AEP) X-2148-118-2 BEZEL ASSY (26) (26S2020 UK/AEP) *X-2109-046-2 BRACKET,(A,TU)(C) ASSY X-2108-491-2 BEZEL ASSY (32) (32S2000 UK/AEP) 8-597-571-00 TUNER UNIT, DIGITAL BTD-HF431Z...
SECTION 6 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page G2 BOARD COMPLETE Parts List : ....................74 BE BOARD COMPLETE Parts List : ....................77 FEE BOARD COMPLETE Parts List : ....................85 TUE BOARD COMPLETE Parts List : ....................