Page 1: Table Of Contents
XG-P10XE SERVICE MANUAL SERVICE-ANLEITUNG S80H2XG-P10XE LCD PROJECTOR LCD PROJEKTOR MODEL XG-P10XE MODELL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
Page 2: Specifications
USB mouse control cable (1.5 m), DIN-D-sub RS-232C cable (15 cm), Remote mouse receiver, Extra air filter, Lens cap (attached), CD-ROM, LCD projector operation manual, LCD projector quick references, Sharp Advanced Presentation Software operation manual Replacement parts Standard lens unit (CLNS-0169CE02), Lamp unit (Lamp/cage module) (BQC-XGP10XE/1),...
Page 3: Note To Service Personnel
(Fig. 1). Note: Please obtain a lens cap before servicing a model XG-P10XE that is received without one. UV-Radiation and Medium Pressure LENS CAP Lamp Precautions 1. Be sure to disconnect the AC plug when replacing the lamp.
Page 4 Laser pointer window Caution Concerning the Lamp Unit Potential hazard of glass particles if lamp ruptures. Please have Sharp Authorised LCD Projector Dealer or Service Centre replace lamp if rupture occurs. CAUTION LAMP MAY RUPTURE.
Page 5: Location Of Controls
XG-P10XE Location of Controls Projector LAMP REPLACEMENT MUTE button indicator TEMPERATURE WARNING POWER indicator indicator POWER buttons (ON/OFF) VOLUME buttons (+/–) LENS button MENU button INPUT button AUTO SYNC button FREEZE button RESIZE button ENLARGE button GAMMA button BLACK SCREEN button...
Page 6: Operating The Wireless Mouse Remote Control
XG-P10XE Operating the Wireless Mouse Remote Control Remote Control Font View Top View Remote control MUTE button signal transmitter Laser VOLUME buttons POWER buttons pointer (+/–) (ON/OFF) window LENS/BLACK LASER POINTER/ SCREEN button MENU button Rear View MOUSE/ RIGHT-CLICK/ ADJUSTMENT ENTER button "...
Page 7: Using The Remote Control As A Wireless Mouse
XG-P10XE Using the Remote Control as a Wireless Mouse The remote control has the following three functions: MOUSE/ADJUSTMENT switch • Projector control (Remote control) • Wireless mouse • Laser pointer MOUSE ADJ. MOUSE ADJ. Wireless mouse Projector control Laser pointer Remote Control/Mouse Receiver Positioning •...
Page 8: Operation Manual
XG-P10XE Use as a Wireless Mouse Be sure the supplied remote mouse receiver is connected to your computer. Slide the MOUSE/ADJUSTMENT switch to MOUSE. MOUSE ADJ. Effective buttons in MOUSE mode LASER BLACK SCREEN POINTER LEFT-CLICK MOUSE RIGHT-CLICK • The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer ’s operation manual for details of setting up/installing the mouse driver.
Page 9: Connection Pin Assignments
XG-P10XE Connection Pin Assignments Analog Computer 1 and 2 Signal Input Ports: 15-pin mini D-sub female connector Computer Input Analog 1. Video input (red) 9. Not connected 2. Video input 10. GND (green/sync on green ) 11. GND 3. Video input (blue) 12.
Page 10 XG-P10XE Dimensions Rear View Top View Side View Front View Bottom View Units: mm...
Page 11: Removing Of Major Parts
XG-P10XE REMOVING OF MAJOR PARTS 1. Removing the Intake cover, lamp unit and lens cover. 1-1. Detach the Intake cover. 1-2. Remove the four lock screws off the inner filter frame. Detach the frame. 1-3. Remove the lock screw off the lamp cover. Slide and detach the lamp cover.
Page 12: Removing The Top Cabinet
XG-P10XE 3. Removing the top cabinet. 3-1. Remove the four lock screws off the top cabinet. 3-2. Unhook the top cabinet by pressing the center of both sides of the bottom cabinet as well as the hook on the front (all marked with `). Slowly lift the back of the cabinet and disconnect the operation key unit connector (KY) and the speaker connector (SP).
Page 13: Removing The Pwb Units
XG-P10XE 4. Removing the PWB units 4-1. Remove the six lock screws off the PC I/F unit. Lift and detach the unit off the output unit. 4-2. Disconnect the connectors from the output unit. 4-3. Remove the four lock screws off the output units. Remove also the lock screw off the ground fixture and detach the ground fixture.
Page 14: Removing The Optical Mechanism Unit
XG-P10XE 5. Removing the optical mechanism unit 5-1. Remove the two lock screws off the lamp socket holder. Detach the holder. 5-2. Disconnect the ground wire from the power unit. 5-3. Disconnect the connector(BA) from AC power switch and connector (PF) from the ballust unit.
Page 15 XG-P10XE 6. Removing the ballast / PFC / sound-out unit assembly. 6-1. Disconnect the ground wire from the inlet unit. 6-2. Remove the two lock screws off the ballast/PFC/sound-out unit assembly. Detach the assembly. 7. Removing the power unit 7-1. Remove the three lock screws off the power PWB. Detach the power unit.
Page 16: Resetting The Total Lamp Timer
“ ” will flash in yellow in the type BQC-XGP10XE/1 from your lower-left corner of the picture. nearest Sharp Authorised LCD Projector Dealer or Service Centre. A significant deterioration of the • Replace the lamp. If you wish, you picture and colour quality occurs.
Page 17: The Optical Unit Outline
XG-P10XE THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system. Projection Lens 1/2λ plate Sapphire glass Polarizing plate 1/2λ plate + polarizing plate Incident polarizing plate B Incident polarizing plate R Dichroic coating...
Page 18: Convergence And Focus Adjustment
XG-P10XE CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top cabinet and the LCD cover removed but the power on. Use the remote control to adjust the image. Take the follow- ing procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1.
Page 19: Convergence And Focus Adjustments Mechanism
XG-P10XE Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism is used for image formation.
Page 20 XG-P10XE Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction Definition Direction of LCD panel X direction LCD right and left Convergence Y direction LCD top and bottom θZ direction Rotation around Z axis LCD turning axis Z direction LCD optical axis θX direction...
Page 21 XG-P10XE Replacing the LCDs With the top cabinet removed (1) Disconnect the LCD flat cable from the output PWB connector. (2) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD panel.
Page 22 XG-P10XE Adjusting the optical axis of the mirrors (M1, M5 and M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced.
Page 23 XG-P10XE Adjusting the lamp duct. turn Lock screws Lamp duct Cooling-Fan (Exhaust) Adjustment procedure reguired when the lamp has been replaced and you can see ununifomity. (Case of Right and Left have ununifomity on the screen) (1) Let the lamp light up.
Page 24 XG-P10XE Adjustment of incident polarizing plate. (Carry it out when removing polarizingplate.) Screw A Screw C Notch & Hole A Notch & Hole C Notch & Hole B Screw B (From the condition that the top cabinet opens.) 1.Remove a screws, earth plate from the output PWB.
Page 25: Electrical Adjustment
XG-P10XE ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. Adjusting point Adjusting conditions Adjusting procedure » Make the following settings: EEPROM 1.
Page 26 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Choose the subject R1-GAIN and adjust the sig- RGB 1 system 1. Make the following choice: black level Group : OUTPUT 1 nal amplitude to 3.25 ±0.03 Vp-p using the control signal amplitude Subject : R1-BLK switches or the remote controller buttons.
Page 27 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller RGB counter- 1. Feed the black-and-red voltage (25%) stripe signal (XGA). buttons, adjust the data in order to minimize the adjustment flicker. 2. Make the following choice: »...
Page 28 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller 1. Feed the split colour bar Video OFFSET signal. buttons, adjust the black portion of the signal adjustment Group : VIDEO 2 becomes bit-less.
Page 29 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller PAL colour 1. Feed the PAL colour bar saturation level signal. buttons, adjust the difference between the 100% Group : VIDEO 1 white portion and the red portion to 0.20 ±0.01 Vp-p.
Page 30 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Adjust the level difference between the 100% white DVD Colour 1. Feed the colour bar signal of the 480I component sig- and red portions to 0.13 ±0.02 Vp-p. nal to the BNC G(Y) input terminal.
Page 31 XG-P10XE Adjusting point Adjusting conditions Adjusting procedure » Make sure that a white balance is the best condi- Checking and 1.The adjustment condition of readjustment of each item is as mentioned tion. white balance in the following. RGB input:Refer to No.13 VIDEO input:Refer to No.23...
Page 32: Trouble Shooting Table
XG-P10XE TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Through-output in trouble Remote control in trouble Go to "Checking the video unit Feed test pattern signal from Through-output circuit in Go to "Checking the remote circuit".
Page 33: Checking The Video Unit Circuit
XG-P10XE TROUBLE SHOOTING TABLE (Continued) Checking the video system Is the lamp on? Go to "Lamp fails to light-up". Is specified voltage fed to EA connectors? Check the power circuit and its parts. Are there signal inputs at pins (7), (9)
Page 34 XG-P10XE TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) Are there RGB output waveforms at pins (31), (32) and (33) of IC801? Go to "No colour or unusual tone", Check the data transfer and other "No Y signal" or "Out of sync".
Page 35 XG-P10XE TROUBLE SHOOTING TABLE (Continued) Checking IC6001 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of IC6001? Check the buffer circuit of Q6004 thru Q6006 as well as Q6001 thru Q6003.
Page 36: No Or Unusual Horizontal Sync
XG-P10XE TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of IC801? Go back to the signal processing block. Is there Y signal output at pin (40) of IC801? Check IC801 and its peripheral circuits.
Page 37 XG-P10XE TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit Are there signal inputs at SC1404, SC1405, SC1501 and SC1502? Are voltages applied to EA connectors and SC8404, If there is no signal at EA If there is no signal at SC8404...
Page 38: No Audio Output
XG-P10XE TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pins (2) and (23) of IC1301? Check the input, the switching circuit of IC441 and IC442, and their peripheral circuit. Are there audio signal outputs at pins...
Page 39 XG-P10XE TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? Select the right input with remote control. Are the PC, video and LCP cables as specified and properly connected? Use the right cables or reconnect the cables. With the contrast control at maximum, does the image appear? Readjust the video system.
Page 40: Lamp Fails To Light-Up
XG-P10XE TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Turn on the power switch. Is discharging sound heard from the lamp? Is the lamp out of socket? Is the ballast cooling fan running? Replace the Reconnect the lamp. lamp into socket.
Page 41 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? X8001 or its peripheral part faulty. Is X8003 (1.84MHz) oscillating? X8003 or its peripheral part faulty. X8004 or its peripheral part faulty.
Page 42 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the PLL circuit and its peripheral circuits Are there signals at pin(111) of IC8606 and TL8606? IC8025 or its peripheral circuit faulty. Is there signal at pins (100) and (101) of IC8606? IC8606 or its peripheral circuit faulty.
Page 43 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the S- Checking the VGA's XGA's red video red video circuit and circuit and its its peripheral peripheral circuits circuits Is there signal at pin (139) of IC8606? Is there signal at pin (139) of IC8606? output PWB faulty.
Page 44 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the S- Checking the VGA's XGA's green video green video circuit circuit and its and its peripheral peripheral circuits circuits Is there signal at pin (124) of IC8606? Is there signal at pin (124) of IC8606? output PWB faulty.
Page 45 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the S- Checking the VGA's XGA's blue video blue video circuit circuit and its and its peripheral peripheral circuits circuits Is there signal at pin (133) of IC8606? Is there signal at pin (133) of IC8606? outpur PWB faulty.
Page 46 XG-P10XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Are there signals at pins (56), (58), (71) and (72) of IC8048? IC8029 or its peripheral circuit faulty. Are there signals at pins (12), (14) thru (17) and (20) of IC8048? IC8048 or its peripheral circuit faulty.
Page 47: Chassis Layout
XG-P10XE CHASSIS LAYOUT / CHASSIS-ANORDNUNG OUTPUT UNIT DUNTKA184DE02 PC I/F UNIT CPCI-0047CE12 INLET UNIT RUNTK0674CEZZ SIGNAL UNIT DUNTKA187DE02 POWER UNIT RDENC0304CEZZ R/C UNIT DUNTKA186DE02 TERMINAL UNIT DUNTKA188DE02 BALLAST UNIT RDENC0302CEZZ PFC UNIT S-OUT UNIT RDENC0305CEZZ DUNTKA185DE02...
Page 48: Block Diagram
XG-P10XE BLOCK DIAGRAM / BLOCKSCHALTBILD...
Page 49: Overall Wiring Diagram
XG-P10XE OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN...
Page 50: Description Of Schematic Diagram
XG-P10XE DESCRIPTION OF SCHEMATIC BESCHREIBUNG DES DIAGRAM SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Spannungen an den Prüfpunkten werden bei einer 1. Voltages at test points are measured at the supply Netzspannung von 230V gemessen, Signale werden voltage of AC 230V. Signals are fed by a colour bar für die Wartung mit einem Farbbalken-Signal...
Page 51: Waveforms
XG-P10XE WAVEFORMS / WELLENFORMEN SC1101 7-pin SC1101 8-pin SC1201 8-pin SC1201 7-pin (RP SIG5) (RP SIG6) (GP SIG6) (GP SIG5) H : 10µsec/div H : 10µsec/div H : 10µsec/div H : 10µsec/div V : 2V/div V : 2V/div V : 2V/div...
Page 52 XG-P10XE Ë SIGNAL UNIT-1/4 / SIGNALEINHEIT-1/4...
Page 53 XG-P10XE Ë SIGNAL UNIT-2/4 / SIGNALEINHEIT-2/4...
Page 54 XG-P10XE Ë SIGNAL UNIT-3/4 / SIGNALEINHEIT-3/4...
Page 55 XG-P10XE Ë SIGNAL UNIT-4/4 / SIGNALEINHEIT-4/4...
Page 56 XG-P10XE Ë OUTPUT UNIT-1/7 / AUSGABEEINHEIT-1/7...
Page 57 XG-P10XE Ë OUTPUT UNIT-2/7 / AUSGABEEINHEIT-2/7...
Page 58 XG-P10XE Ë OUTPUT UNIT-3/7 / AUSGABEEINHEIT-3/7...
Page 59 XG-P10XE Ë OUTPUT UNIT-4/7 / AUSGABEEINHEIT-4/7...
Page 60 XG-P10XE Ë OUTPUT UNIT-5/7 / AUSGABEEINHEIT-5/7...
Page 61 XG-P10XE Ë OUTPUT UNIT-6/7 / AUSGABEEINHEIT-6/7...
Page 62 XG-P10XE Ë OUTPUT UNIT-7/7 / AUSGABEEINHEIT-7/7...
Page 63 XG-P10XE Ë TERMINAL UNIT-1/2 / ANSCHLUßEINHEIT-1/2...
Page 64 XG-P10XE Ë TERMINAL UNIT-2/2 / ANSCHLUßEINHEIT-2/2...
Page 65 XG-P10XE Ë SOUND OUT UNIT / TONAUSGABEEINHEIT...
Page 66 XG-P10XE Ë R/C RECEIVER UNIT / FERNBEDIENUNGSEINHEIT...
Page 67 XG-P10XE Ë OPERATION KEY UNIT / BEDIENUNGSTASTENEINHEIT...
Page 68 XG-P10XE Ë PFC AND INLET UNIT / LEITUNGSFILTER-SCHALTUNG UND EINGANGSEINHEIT (PFC) (INLET)
Page 69 XG-P10XE Ë POWER UNIT / NETZEINHEIT RDENC0304CEZZ...
Page 70 XG-P10XE Ë PC I/F UNIT-1/9 / PC-I/F-EINHEIT-1/9...
Page 71 XG-P10XE Ë PC I/F UNIT-2/9 / PC-I/F-EINHEIT-2/9...
Page 72 XG-P10XE Ë PC I/F UNIT-3/9 / PC-I/F-EINHEIT-3/9...
Page 73 XG-P10XE Ë PC I/F UNIT-4/9 / PC-I/F-EINHEIT-4/9...
Page 74 XG-P10XE Ë PC I/F UNIT-5/9 / PC-I/F-EINHEIT-5/9...
Page 75 XG-P10XE Ë PC I/F UNIT-6/9 / PC-I/F-EINHEIT-6/9...
Page 76 XG-P10XE Ë PC I/F UNIT-7/9 / PC-I/F-EINHEIT-7/9...
Page 77 XG-P10XE Ë PC I/F UNIT-8/9 / PC-I/F-EINHEIT-8/9...
Page 78 XG-P10XE Ë PC I/F UNIT-9/9 / PC-I/F-EINHEIT-9/9...
Page 79: Printed Wiring Board Assemblies
XG-P10XE PRINTED WIRING BOARD ASSEMBLIES/ LEITERPLATTENEINHEITEN Signal Unit (Wiring Side)/ Signaleinheit (Leiterbahnseite) Signal Unit (Component Side)/ Signaleinheit (Bestückungsseite)
Page 80 XG-P10XE Terminal Unit (Wiring Side)/ Anschlußeinheit (Leiterbahnseite) Terminal Unit (Component Side)/ Anschlußeinheit (Bestückungsseite)
Page 81 XG-P10XE R/C Receiver Unit (Wiring Side)/ Fernbedienungseinheit (Leiterbahnseite) Output Unit (Wiring Side)/ Ausgabeeinheit (Leiterbahnseite)
Page 82 XG-P10XE R/C Receiver Unit (Component Side)/ Fernbedienungseinheit (Bestückungsseite) Output Unit (Component Side)/ Ausgabeeinheit (Bestückungsseite)
Page 83 XG-P10XE PFC Unit (Wiring Side)/ Leitungsfilter-Schaltung-Einheit (Leiterbahnseite) Sound Out Unit (Wiring Side)/ Tonausgabeeinheit (Leiterbahnseite) Power Unit (Wiring Side)/ Netzeinheit (Leiterbahnseite)
Page 84 XG-P10XE PFC Unit (Component Side)/ Leitungsfilter-Schaltung-Einheit (Bestückungsseite) Sound Out Unit (Component Side)/ Tonausgabeeinheit (Bestückungsseite) Power Unit (Component Side)/ Netzeinheit (Bestückungsseite)
Page 85 XG-P10XE PC I/F Unit (Wiring Side) / PC-I/F Einheit (Leiterbahnseite) PC I/F Unit (Component Side) / PC-I/F Einheit (Bestückungsseite)
Page 86 XG-P10XE Inlet Unit (Wiring Side)/ Inlet Unit (Component Side)/ Eingangseinheit (Bestückungsseite) Eingangseinheit (Leiterbahnseite)
Page 87: Ersatzteilliste
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code PARTS LIST ERSATZTEILLISTE AUSTAUSCH VON TEILEN PARTS REPLACEMENT Ersatzteile, die besondere Sicherheitseigenschften haben, sind in Replacement parts which have these special safety characteristics dieser Anleitung markiert. Elektrische Komponenten mit solchen identified in this manual: electrical components having such fea- Eigenshaften sind in den Ersatzteil durch "å"...
Page 88 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA184DE02 Q1606 VSDTC144EU/-1 J DTC144EU Q1607 VSDTC144EU/-1 J DTC144EU OUTPUT UNIT (Continued) Q1608 VSDTC144EU/-1 J DTC144EU Q1609 VSDTC144EU/-1 J DTC144EU IC5102 VHiLB1831M/-1 J LB1831M Q1610 VSDTC144EU/-1 J DTC144EU...
Page 89 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA184DE02 CAPACITORS [ MLFT ··· Multi Layer Film Tip ] OUTPUT UNIT (Continued) C301 VCEAPV1CW476M J 47 Electrolytic C302 VCKYCY1HB102K J 1000p 50V Ceramic DIODES C303 VCE9PF1CW106M J 10 Elect.(N.P)
Page 90 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA184DE02 C2132 VCKYCY1AF105Z J 1.0 Ceramic C2133 VCKYCY1EF104Z J 0.1 Ceramic OUTPUT UNIT (Continued) C2134 VCKYCY1EF104Z J 0.1 Ceramic C2135 VCKYCY1EF104Z J 0.1 Ceramic C1310 RC-KZ0416CEZZ J 10...
Page 91 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA184DE02 C7022 VCEAPV0JW107M J 100 6.3V Electrolytic C7051 VCEAPV1CW476M J 47 Electrolytic OUTPUT UNIT (Continued) C7052 VCKYCY1CF104Z J 0.1 Ceramic C7053 VCEAPV0JW107M J 100 6.3V Electrolytic C4217 VCKYCY1EF104Z J 0.1...
Page 92 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R1167 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide DUNTKA184DE02 R1168 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide OUTPUT UNIT (Continued) R1169 VRS-CY1JF3R3J J 3.3 1/16W Metal Oxide R1171 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide...
Page 93 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R1358 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide DUNTKA184DE02 R1361 VRS-CY1JF000J 1/16W Metal Oxide OUTPUT UNIT (Continued) R1362 VRS-CY1JF000J 1/16W Metal Oxide R1364 VRS-CY1JF101J J 100 1/16W Metal Oxide R1266 VRS-CY1JF222J J 2.2k 1/16W Metal Oxide...
Page 94 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R2222 VRS-CY1JF000J 1/16W Metal Oxide DUNTKA184DE02 R2224 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide OUTPUT UNIT (Continued) R2231 VRS-CY1JF000J 1/16W Metal Oxide R2232 VRS-CY1JF000J 1/16W Metal Oxide R1659 VRS-CY1JF203J...
Page 95 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R5106 VRS-CY1JF000J 1/16W Metal Oxide DUNTKA184DE02 R5107 VRS-CY1JF000J 1/16W Metal Oxide OUTPUT UNIT (Continued) R5108 VRS-CY1JF000J 1/16W Metal Oxide R5109 VRS-CY1JF000J 1/16W Metal Oxide R2681 VRS-CY1JF104J J 100k 1/16W Metal Oxide...
Page 96 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R7006 VRS-CY1JF103J J 10k 1/16W Metal Oxide DUNTKA184DE02 R7008 VRS-TX2HF1R0J J 1.0 1/2W Metal Oxide OUTPUT UNIT (Continued) R7009 VRS-TX2HF1R0J J 1.0 1/2W Metal Oxide R7011 VRS-TX2HF2R2J J 2.2...
Page 97 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code SWITCHES DUNTKA184DE02 S4201 QSW-S0198CEZZ J Slide Switch OUTPUT UNIT (Continued) SW2601QSW-K0065GEZZ J Key Switch R7234 VRS-CY1JF393F J 39k 1/16W Metal Oxide MISCELLANEOUS PARTS R7235 VRS-CY1JF473J J 47k 1/16W Metal Oxide F1401 QFS-L8012CEZZ J Fuse 0.8A...
Page 98 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code Q6011 VS2SC3928AR-1 J 2SC3928AR DUNTKA187DE02 Q6012 VS2SC3928AR-1 J 2SC3928AR SIGNAL UNIT Q6013 VS2SC3928AR-1 J 2SC3928AR INTEGRATED CIRCUITS DIODES IC801 VHiTDA8854H-2 J TDA8854H/N2 D801 VHDDAN202K/-1 J Diode IC802...
Page 99 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code C4526 VCKYCY1CF104Z J 0.1 Ceramic DUNTKA187DE02 C4527 VCKYCY1CF104Z J 0.1 Ceramic SIGNAL UNIT (Continued) C4528 VCEAPF0JW476M J 47 6.3V Electrolytic C4529 VCKYCY1HB103K J 0.01 Ceramic C860 VCCCCY1HH100D...
Page 100 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R824 VRS-CY1JF682J J 6.8k 1/16W Metal Oxide DUNTKA187DE02 R825 VRS-CY1JF392J J 3.9k 1/16W Metal Oxide SIGNAL UNIT (Continued) R826 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide R827 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide...
Page 101 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R4521 VRS-CY1JF000J 1/16W Metal Oxide DUNTKA187DE02 R4522 VRS-CY1JF101J J 100 1/16W Metal Oxide SIGNAL UNIT (Continued) R4523 VRS-TV1JD000J 1/16W Metal Oxide R4524 VRS-CY1JF000J 1/16W Metal Oxide R930 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide...
Page 102 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA187DE02 DUNTKA185DE02 SIGNAL UNIT (Continued) SOUND OUT UNIT INTEGRATED CIRCUIT R6024 VRS-TV1JD122J J 1.2k 1/16W Metal Oxide R6025 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide IC302 VHiTDA1517/-2 J TDA1517/N2...
Page 103: Terminal Unit
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code D3005 VHDMA157A//-1 J Diode DUNTKA188DE02 D3006 VHDMA157A//-1 J Diode TERMINAL UNIT D3007 VHDMA157A//-1 J Diode D3201 VHDMA157A//-1 J Diode INTEGRATED CIRCUITS D3202 VHDMA157A//-1 J Diode D3203 VHDMA157A//-1...
Page 104 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code C4030 VCKYCY1CF104Z J 0.1 Ceramic DUNTKA188DE02 C4031 VCKYCY1CF104Z J 0.1 Ceramic TERMINAL UNIT (Continued) C4032 VCKYCY1CF104Z J 0.1 Ceramic C4033 VCKYCY1CF104Z J 0.1 Ceramic C451 VCEAPF1CW106M J 10...
Page 105 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R3208 VRS-CY1JF473J J 47k 1/16W Metal Oxide DUNTKA188DE02 R3209 VRS-CY1JF000J 1/16W Metal Oxide TERMINAL UNIT (Continued) R3210 VRS-CY1JF473J J 47k 1/16W Metal Oxide R3211 VRS-CY1JF000J 1/16W Metal Oxide...
Page 106 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code FB3306 RBLN-0060TAZZ J Ferrite Bead DUNTKA188DE02 FB3401 RBLN-0060TAZZ J Ferrite Bead TERMINAL UNIT (Continued) FB3402 RBLN-0060TAZZ J Ferrite Bead FB3403 RBLN-0060TAZZ J Ferrite Bead R3526 VRS-CY1JF271J J 270 1/16W Metal Oxide...
Page 107: Power Unit
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code C720 9FJ0C01402193 J 470 Electrolytic RDENC0304CEZZ C721 9FJ0C01510165 J 47 Electrolytic POWER UNIT C722 9FJ0C01302085 J 470 Electrolytic C723 9FJ0C01510165 J 47 Electrolytic INTEGRATED CIRCUITS C724 9FJ0C50002635 J 0.047 50V...
Page 108 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code R776 9FJ0R91501055 J 330k 1/10W Chip RDENC0305CEZZ R777 9FJ0R91501055 J 330k 1/10W Chip PFC UNIT R778 9FJ0R91501055 J 330k 1/10W Chip R779 9FJ0R91501055 J 330k 1/10W Chip...
Page 109 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0047CE12 FL8056 9DK001-82026 J Filter, STS104B FL8057 9DK001-82026 J Filter, STS104B PC I/F UNIT FL8058 9DK001-82026 J Filter, STS104B FL8600 9DK001-82026 J Filter, STS104B INTEGRATED CIRCUITS FL8601 9DK001-82026...
Page 110 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0047CE12 C8646 9DK001-42094 J 0.1 Ceramic C8647 9DK001-42096 J 0.01 Ceramic PC I/F UNIT (Continued) C8648 9DK001-40079 J 47 Electrolytic C8649 9DK001-42094 J 0.1 Ceramic C8285 9DK001-42096 J 0.01...
Page 111 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0047CE12 R8253 9DK001-50159 J 22 1/16W Chip1608 R8254 9DK001-50159 J 22 1/16W Chip1608 PC I/F UNIT (Continued) R8255 9DK001-50159 J 22 1/16W Chip1608 R8257 9DK001-50185 J 10k 1/16W Chip1608...
Page 112 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0047CE12 PC I/F UNIT (Continued) R8610 9DK001-50165 J 100 1/16W Chip1608 R8611 9DK001-50176 J 820 1/16W Chip1608 R8612 9DK001-50176 J 820 1/16W Chip1608 R8613 9DK001-50204 J 150 1/16W Chip1608...
Page 113: Cabinet And Mechanical Parts
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code Not Available – Lamp Cage Cover — CABINET AND MECHANICAL PARTS GCOVH1322CESA J Cap HiNDP5398CESD J Coution Label LX-BZ1009CEFN J Screw Not Available – Top Cabinet Ass’y —...
Page 114: Ë Gehäuse Und Mechanische Bauteile
XG-P10XE CABINET AND MECHANICAL PARTS/ Ref. No. Part No. Description Code Ref. No. Part No. Description Code GEHÄUSE UND MECHANISCHE BAUTEILE 1-1-7 1-1-4 1-1-6 1-1-4 1-1-5 1-1-3 1-1-1 1-1-2 1-11 1-1-3 1-11 1-10 3-23 3-19 3-21 3-11 3-12 3-10 3-18...
Page 115 XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code 6-42 PMiR-0186CEZZ J Mirror-6 OPTICS MECHANISM PARTS 6-43 PMiR-0269CEZZ J PBS 6-44 PMiR-0264CEZZ J Cross Prism (with Base) 6-46 RLCDP0102CEN1 J LCD Module Unit, Red CCHSK0062CE09 J Optics Macha. Ass’y...
Page 116 XG-P10XE OPTICS MECHANISM PARTS/ Ref. No. Part No. Description Code Ref. No. Part No. Description Code TEILE FÜR OPTIKMECHANISMUS...
Page 117: Supplied Accessories
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code SERVICE JIGS SUPPLIED ACCESSORIES (Use for servicing) PFiLD0080CEZZ J Extra Air Filter 9DASPN-XGNV1U J Spanna, 3mm QACCV4002CEZZ J AC Cord (for Europe) (Off-set Cam Adjustment) å QACCB5024CEZZ...
Page 118: Verpacken Des Geräts
XG-P10XE Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET / VERPACKEN DES GERÄTS CD-ROM / CD-ROM Extra Air Filter / Ersatz-Luftfilter Operation Manual / Bedienungsanleitung Quick Reference / Übersicht CD-ROM Manual / CD-ROM-Handbuch...
Page 119: Sharp Corporation
Code Ref. No. Part No. Description Code COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Sharp XG-P10XE Service Manual

Quick Links

SHARP CORPORATION

Related Manuals for Sharp XG-P10XE

Summary of Contents for Sharp XG-P10XE

Table of Contents