Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Connect a 1500 ohm, 10 watt resistor, paralleled by a 0.15uF capacitor between each exposed metallic part and a good earth ground (as shown in Fig.1). Use an AC voltmeter with 1000 ohm/volt or more sensitivity and measure the AC voltage across the ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 5
It is essential that these critical parts should be replaced with manufacture’s specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design or this will void the original parts and labor guarantee. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
This monitor has power saving function following the VESA DPMS. Be sure to connect the signal cable to the PC. If your color display requires service, it must be returned with the power cord. ViewSonic Corporation Confidential - Do Not Copy...
Use the buttons on the front control panel to display and adjust the OSD controls .The OSD controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 8. ViewSonic Corporation Confidential - Do Not Copy...
3 below). Press button [2] to toggle to the next control in the pair. To adjust the setting, such as CONTRAST in the sample below, press the arrow buttons. 4 To save the control setting and Exit the menu press button [1] twice. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 11
Trapezoid adjusts the top and bottom of the screen image until they have equal length. Parallel slants the vertical edges of the screen image until they are parallel. Tilt rotates the entire screen image. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 12
Exception: This control does not affect changes made with the User Color control. OSD Position allows you to move the on-screen display menus and control screens. ViewMeter displays the frequencies (horizontal and vertical) coming from the graphics card of the computer. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Via deflection reset after start up(only micro controller reset) The reset pin(pin23) is connected to a Schmitt trigger for nose reduction. A reset is accomplished by holding the Reset pin HIGH. C145 RST Pin23 C102 R153 0.1UF 2.7K ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 14
60 kHz).Independent on H-syncs which are possibly present.the HPLL will slew to that freerunning frequency.To achieve an always defined starting point for the startup procedure,this procedure cannot be interrupted. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 15
HOR. Driver Transistor Q417,Q418,Q416,Q420 Horizontal s correction control MOSFET Q406 Transistor for H-Size Control Q705 Brightness Control CKT Q742 V-Dynamic focus CKT Q402 Q403 Driver MOSFET Q901 MOS FET for Switching Power Control. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
OSD window changed to the Factory preset window. C. The Factory preset window contains the following functional controls. Select one of the control. Then press the Up/Down Key to adjust its value for the optimum picture. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 17
OSD EXIT H-DRIVER COMPENSATION MAX V-SIZE GAIN RANGE H-MOIRE REDUCE H-SIZE GAIN V-MOIRE REDUCE SUB H-SIZE TOP CORNER H-Linearity Modify BOTTOM CORNER V-FOCUS ADJUST V-HV Variation rate ajust BURN IN TIME ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 18
F. adjust R or G or B gain, make x=283±10, y=297±10, Y=150±5 cd/m ,then save it into 9300K color temprature G. After modulation, it’s necessary to check if the white balance accords with the normal specification. If not, which needs reset. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 19
F. Vertical green and magenta lines are converged by varying the angle between the two tabs of the 6-pole magnets. G. Horizontal green and magenta lines are converged by varying the two tabs together, keeping the angle between them constant. ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
CHECK FBT BRIGHTNESS SET TO MAX. THEN CHECK CRT G1 VOLTAGE CHECK BRIGHTNESS CIRCUIT Q705 RELATIVE CIRCUIT CHECK VOLTAGE OF THE CRT CATHODE ABOUT 56V TO 65V REFER ITEM 6-2 "ABNORMAL ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
R.G.B. APPROACH STANDARD 6-1-3. ABNORMAL DDC (PLUG & PLAY) CHECK IC101 PIN 16 VOLTAGE ABOUT 5V CHECK IC902 GOOD OR FAIL CHECK SIGNAL CABLE OR H802 PIN 2, 4 DATA OUTPUT ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 22
RELATIVE CIRCUIT CHECK THE VOLTAGE OF FBT SCREEN ABOUT 400V TO 700V LESS THAN 400V CHECK FBT RELATIVE CIRCUIT EXCEED 700V CHECK FBT & CRT RELATIVE CIRCUIT OR REFER ITEM 6-1 ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 23
CHECK THE COLLECTOR VOLTAGE OF Q402 ABOUT 14Vpp CHECK Q402, T401 RELATIVE CIRCUIT CHECK THE COLLECTOR VOLTAGE OF Q403 ABOUT 1200Vpp AT FH:31KHz CHECK T401, T402, Q402, Q403, D408, C418, C419, H-DY, B+ ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 24
CHECK FBT B+ VOLTAGE ABOUT 62V AT FH=31KHz CHECK THE RELATIVE CIRCUIT OF SMPS. CHECK THE HV OF CRT ABOUT 25KV 6-5-2. ABNORMAL HORIZONTAL LINEARITY CHECK L401, Q426, Q420, Q427 AND IC101 PIN9,10,11 ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 25
RELATIVE CKT 6-7 . SIDE-PIN CUSHION DISTORTION READJUST CHECK IC101, Q406 RELATIVE CKT. 6-8 . POOR FOCUS READJUST FOCUS CONTROL CHECK FOCUS CONTROL UNIT, FOCUS LEAD WIRE, CRT SOCKET & CRT ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions. ViewSonic Corporation...
Page 28
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Page 29
BOM LIST (E90fB-4 for "M & G-Region) ViewSonic Model Number: VS10794-1M/G Rev: 1a Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty CMP985D1NVSC B-00004051 CHASSIS FOR P985D-1VSC¡] -4M¡^ B-00004052 CMP985D1NVW CHASSIS FOR B985D-1VSC¡] -4G¡^ #N/A 1C 503 5T 47...
11. PCB Layout Diagrams 11-1 MAIN PCB LAYOUT ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 54
11-2 CRT BOARD LAYOUT ViewSonic Corporation Confidential - Do Not Copy E90fB -4...
Page 55
Add: Tel: Fax: E- mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) ViewSonic Corporation Confidential - Do Not Copy...
Need help?
Do you have a question about the PerfectFlat E90fB-4 and is the answer not in the manual?
Questions and answers