Connecting the complete Kit with a TivuSat DS510M receiver and a 19" Teleco United TV (Italy only)..13 Connecting the complete Kit with a TNT SD M6000 receiver and a 19" Teleco United TV (France only)...14 Connecting the complete Kit with a TNT HD M5200/M7000 receiver and a 19"...
List of accessories Flat Sat Elegance is delivered inside a cardboard case that has been specially made to protect it from knocks and pressure. The following accessories are supplied: External motor-driven unit 65-85 cm dish Universal LNB SKEW (OPTIONAL) Black Box MIR remote control expander Motor Connection Cable Antenna/Black Box Connection Lead...
Important notice Flat Sat Elegance is packaged in two separate cartons for transport reasons: a) the first package contains the driving unit with all the cables, and the Black Box; b) the second package only contains the dish. • It is important to check that the dish has not been damaged during transport when the package is opened.
Assembly instructions 1) Position the Black Box in an easy accessible, ventilated compartment. 2) On the roof of the vehicle, choose a free area large enough to allow the antenna to revolve (Fig. 2). 3) Install the connection cables (Grey and White) until you reach the powered OUTSIDE UNIT installation area.
Page 6
Driving direction of the vehicle Driving direction of the vehicle When they are present, remove the transparent films from the BASE PLATE (Fig. 5). 7) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the whole surface (e.g.
Installation with cables coming out sideways 10) Fasten the OUTSIDE UNIT on the base plate and lead the two cables through any of the 4 existing grooves, according to the position as shown on Fig. 6. WARNING: When performing this operation, do not draw the two cables forcefully, as this might pull them out.
Installation with cables through the centre of the base plate WARNING The Grey and White cables coming out of the Outside Unit are generally long enough to allow for connection to the Black Box. If it is not so, use the extension cables and perform the following operations: Connection with extension 13) Connect the Grey and White extension cables, coming from inside the vehicle (Fig.
Page 9
14) Install the OUTSIDE UNIT on the base plate, remembering that: a) The right position is the one shown on (Fig. 13).. b) Apply an abundant layer of silicone on both the base plate and the bottom of the driving unit so as to prevent any infiltration by water.
Flat Sat Elegance – Front Black Box View 1) Power-on indication LED Flat Sat Elegance – Rear Black Box View 1) F type connector – input from LNB converter of the driving unit 2) F type connector – signal output to be connected to any satellite receiver 3) B type USB connector –...
Kit-matching devices. The label which is applied on the back of the devices is as follows: Example: Black Box Rec Type: Force HD CI+ (A) TV Type: 19" Teleco United (d) Remote Rec Type: Force HD CI+ (A) control TV Type: 19" Teleco United (d)
Complete Kit with TivuSat DS510M receiver and 19" Teleco United TV (Italy only) Complete Kit with TNT SD M6000 receiver and 19" Teleco United TV (France only) Complete Kit with TNT HD M5200/M7000 receiver and 19" Teleco United TV (France only)
Connecting the complete Kit with a Sat FORCE HD CI+ receiver and a 19" Teleco United TV FORCE HD CI+ White Not connected Grey black Green TV 19" TELECO United WARNING Any power connection made in points other than as indicated (e.g. on the...
Connecting the complete Kit with a TivuSat DS 510M receiver and a 19" Teleco United TV (Italy only) DS 510M AUDIO ON/OFF VIDEO SPDIF MODEM White Not connected Grey black Green TV 19" TELECO United WARNING Any power connection made in points other than as indicated (e.g.
Connecting the complete Kit with a TNT SD M6000 receiver and a 19" Teleco United TV (France only) TNT SAT SD M 6000 SPDIF VCR SCART TV SCART DC IN White Not connected Grey black Green TV 19" TELECO United...
Connecting the complete Kit with a TNT HD M5200/M7000 receiver and a 19" Teleco United TV (France only) TNT SAT HD M 5200/M7000 LNB IN HDMI AUDIO TV SCART DC IN White Not connected Grey black Green TV 19" TELECO United...
Kit with Black Box and Sat Decoder, without TV This configuration will allow you to: • control your Black Box and DECODER with ONE remote control, but NOT your TV. You can switch the Black Box and the Decoder on and off via one button. •...
Connecting the Kit with a Sat FORCE HD CI+ Receiver FORCE HD CI+ White connected Grey black Green TV Not Supplied WARNING Any power connection made in points other than as indicated (e.g. on the alternator) can give rise to equipment malfunction and/or damage resulting in loss of the warranty.
Connecting the Kit with a TivuSat DS510M Receiver (Italy only) DS510M AUDIO ON/OFF VIDEO SPDIF MODEM White connected Grey black Green TV Not Supplied WARNING Any power connection made in points other than as indicated (e.g. on the alternator) can give rise to equipment malfunction and/or damage resulting in loss of the warranty.
Connecting the Kit with a TNT SAT SD M 6000 Receiver (France only) TNT SAT SD M 6000 SPDIF VCR SCART TV SCART DC IN White connected Grey black Green TV Not Supplied WARNING Any power connection made in points other than as indicated (e.g.
Connecting the Kit with a TNT SAT HD M5200/M7000 receiver (France only) TNT SAT HD M5200/M7000 LNB IN HDMI AUDIO TV SCART DC IN White connected Grey black Green TV Not Supplied WARNING Any power connection made in points other than as indicated (e.g. on the alternator) can give rise to equipment malfunction and/or damage resulting in loss of the warranty.
Configuration without Kit By this configuration, the remote control only controls your Black Box. The TV and DECODER are not part of a Kit, they will therefore be controlled via the remote controls supplied by the related manufacturers. Connection diagram a) Connect the grey cable (motors) to the MOTOR UNIT connector and the white coax cable (antenna) to the LNB connector of the Black Box.
WARNING This technical note is to call the attention of the installation personnel to certain details of Flat Sat Elegance installation. During installation, you must take the following precautions: The power supply cable must directly come from the battery and must have no junctions. Minimum cross section of the cable is 5 mm .
1) Remove the LNB protective cover by screwing out the 3 screws 2) Loosen the screws on the LNB locking U-bolt 3) Turn in the Clockwise (West) or Anti-clockwise (South-East) direction 4) Lock the LNB again by screwing down the screws 5) Close back the LNB protective cover and screw down the 3 screws Place Position...
Page 34
CONFORMITY CERTIFICATE The manifacturer Teleco Spa Via Majorana nr. 49, 48022 Lugo ( RA ) Declares under its own responsibility that the following products: FLAT SAT Elegance which are the subject of this certificate, conform to the following norms: EN 60065: 2002 EN 55013: 2001 + A1: 2003 EN 61000 –...