Page 1
Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way.
LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 8
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 9
Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
Page 10
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is Pb free mark will be found on PCBs which use Pb indicated as shown. free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder.
Page 12
around the flat pack-IC to protect other parts from With Soldering Iron: damage. (Fig. S-1-2) 1. Using desoldering braid, remove the solder from 3. The flat pack-IC on the CBA is affixed with glue, so all pins of the flat pack-IC. When you use solder be careful not to break or damage the foil of each flux which is applied to all pins of the flat pack-IC, pin or the solder lands under the IC when...
Page 13
2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 14
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
Page 16
Note: 3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then (1) Order of steps in procedure. When reassembling, remove the solder from the three short lands of follow the steps in reverse order. These numbers FPC cable.
Page 18
(S-5) (S-7) (S-6) [3] DVD Holder [5] DVD Main CBA Unit (S-6) [4] DVD Mechanism Remove two screws A, then short the three short lands by soldering as shown in View for A. Chassis Cover Screws A Pin A Either of two places View for A FPC Cable Hole A...
Page 19
[7] Digital Main CBA Unit (S-11) [6] Jack Holder(D) (S-8) (S-9) Shield Box (S-10) (H-1) (S-9) (S-12) [8] Jack Holder(A) (S-13) [9] Jack CBA (S-14) (S-14) [10] Main CBA Fig. D3 A94N1DC...
TV Cable Wiring Diagram To DVD Mechanism CN301 CN801 CN401 CN201 To LCD Module Assembly To LCD Module DVD Main CN601 Assembly CBA Unit Digital Main Main CBA CBA Unit CN201 CN3902 CN301 CN3701 CN1001 CN302 CN3702 CN4001 CN303 CN1002 Jack CBA CN902 CN702...
Fig. 3 How to make the Service remote control unit: How to set up the service mode: [LD195SSX, LD190EM1, LD190SS1] Service mode: 1. Use the service remote control unit. Cut “A” portion of the attached remote control unit as 2. Turn the power on.
Page 23
1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, Test Point Adj. Point green, blue, and white to check for non-active pixels. [CHANNEL UP/DOWN ] Screen 1. Enter the Service mode. buttons 2. Each time pressing [7] button on the service M.
Page 24
The White Balance Adjustment should be 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff performed when replacing the LCD Panel adjustment. Press [3] button to select “COB” for or Digital CBA. Blue Cutoff adjustment. [DRIVE] 3. White Balance Adjustment Press [4] button to select “DR”...
HOW TO INITIALIZE THE LCD TV/DVD The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure.
FIRMWARE RENEWAL MODE < DVD Section > 5. After programming is finished, the disc will be ejected automatically. Fig. c appears on the 1. Turn the power on and press [EJECT] button on screen and the checksum will be shown in (*2). the remote control unit to put the LCD TV/DVD into "...
Page 27
< LCD TV Section > The appearance shown in *1 is described as follows. Appearance State Equipment Required Downloading the firmware from Downloading... the USB memory. a. USB memory Writing the downloaded firmware b. Remote Control Unit Writing... in flash memory. Checking...
TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (D601, D602, D603, D604, Q601, Q602, T601) Is the INV+31V line voltage normal? FLOW CHART NO.2...
Page 29
FLOW CHART NO.6 PANEL+24.5V is not output. FLOW CHART NO.7 PANEL+13V is not output. FLOW CHART NO.8 P-ON+7V is not output. FLOW CHART NO.9 P-ON+5V is not output. (PANEL+13V is outputted normally.) Replace Q635 and Q636. A94N1TR...
Page 30
FLOW CHART NO.10 TUNER+5V is not output. (PANEL+13V is outputted normally.) Replace Q637. FLOW CHART NO.11 P-ON+3V is not output. FLOW CHART NO.12 P-ON+3.3V(PANEL+3.3V) is not output. FLOW CHART NO.13 EV+3.3V is not output. A94N1TR...
Page 31
FLOW CHART NO.14 DVD-ON+3.3V is not output. FLOW CHART NO.15 EV+9V is not output. (PANEL+13V is outputted normally.) FLOW CHART NO.16 EV+1.2V is not output. Replace IC901. FLOW CHART NO.17 P-ON+9V is not output. (PANEL+13V is outputted normally.) Replace Q641. A94N1TR...
Page 32
FLOW CHART NO.18 AL+3.3V is not output. FLOW CHART NO.19 LCD-7.1V is not output. Replace Q206. A94N1TR...
Page 33
[ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Re-install the switches (SW104~SW109, SW951~SW953) correctly or replace the poor switch. Check the switches (SW104~SW109, SW951~SW953) and their periphery, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit.
Page 34
FLOW CHART NO.4 Picture does not appear normally.(Tuner input) FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr FLOW CHART NO.7 Picture does not appear normally.(DVD PB) Pin(9) : DVD-Y...
Page 35
[ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Check the line between Pin(4, 11) of IC771 and input...
Page 36
FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Check TU302 and their periphery circuit, and service it if defective. Check SP861,SP862 and their periphery circuit, and service it if defective. FLOW CHART NO.4 Audio is not outputted normally.(HDMI Audio input) Check the line between Pin(5, 14) of IC771 and input terminal(JK721, JK722), and service it if defective.
Page 37
FLOW CHART NO.5 Audio is not outputted normally.(PC Audio input) Check the line between Pin(1, 12) of IC771 and input terminal(JK711), and service it if defective. Check SP861,SP862 and their periphery circuit, and service it if defective. 9-10 A94N1TR...
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 47
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 51
Main 4/4 Schematic Diagram [LD195SSX, LD195EMX, 19MD359B/F7] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 55
Main 4/4 Schematic Diagram [19MD350B/F7, LD190SS1, LD190EM1] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 56
Jack & Junction-C Schematic Diagram A94N1SCJ 11-11...
Page 57
Function & Junction-A Schematic Diagram 11-12 A94N1SCF...
Page 58
Digital Main 1/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 11-13 A94N1SCD1...
Page 59
Digital Main 2/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. A94N1SCD2 11-14...
Page 60
Digital Main 3/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 11-15 A94N1SCD3...
Page 61
Digital Main 4/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. 11-16 A94N1SCD4...
Page 62
Digital Main 5/5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section. A94N1SCD5 11-17...
Page 63
DVD Main 1/3 Schematic Diagram 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. A94N1SCDV1 11-18...
Page 64
DVD Main 2/3 Schematic Diagram A94N1SCDV2 11-19...
Page 65
DVD Main 3/3 Schematic Diagram A94N1SCDV3 11-20...
Page 66
Main CBA Top View [LD195SSX, LD195EMX, 19MD359B/F7] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
Page 67
Main CBA Bottom View [LD195SSX, LD195EMX, 19MD359B/F7] CAUTION ! Because a hot chassis ground is present in the power supply Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. circuit, an isolation transformer must be used when repairing.
Page 68
Main CBA Top View [19MD350B/F7, LD190SS1, LD190EM1] CAUTION ! Because a hot chassis ground is present in the power supply Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. circuit, an isolation transformer must be used when repairing. CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply...
Page 69
Main CBA Bottom View [19MD350B/F7, LD190SS1, LD190EM1] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. Also, in order to have the ability to increase the input slowly, CAUTION ! : For continued protection against risk of fire,...
Page 70
Jack CBA Top View J 8 1 0 R 7 5 6 P - O N + 9 V Q 8 4 1 J 8 1 8 R 7 5 7 R 7 5 8 S P D I F J K 8 4 1 J K 7 1 1 J K 7 4 1...
Page 71
Jack CBA Bottom View B C 8 4 1 C 8 4 2 R 8 4 7 R 8 4 5 R 8 4 6 C 7 5 4 C 7 5 5 C 8 4 3 J 8 1 0 R 7 5 6 P - O N + 9 V Q 8 4 1...
Page 72
Function CBA Top View L C 7 1 9 / 2 2 W B A S E R S 1 0 1 B A 9 4 N 0 F 0 1 0 2 2 / G R E E N / O R A N G E / R E D P O W .
Page 73
Junction-A CBA Top & Bottom View Junction-C CBA Top & Bottom View C L 8 6 1 C L 8 6 1 C N 8 6 1 B C N 8 6 1 B BA94N0F01022 BA94N0F01022 Junction-B CBA Top & Bottom View C L 8 6 2 C L 8 6 2 C N 8 6 2 B...
WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) Pin 4 of CN302 Pin 17 of CN302 CVBS 0.2V 20µs VIDEO-Pb 0.2V 20µs Pin 8 of CN302 Pin 19 of CN302 20µs...
Page 75
WF8 ~ WF13 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) DVD Video (Play MODE) Pin 5 of CN902 Pin 9 of CN902 WF11 DVD-AUDIO(L) 0.5V 0.5ms DVD-Y 0.5V...
LEAD IDENTIFICATIONS KTA1267-GR-AT/P 2SA950-Y(TE2 F T) 2SA1020-Y(TE6 F M) 2SC2120-Y(TE2 F T) 2SK3563(Q) 2SC4881F 2SC2655-Y(TE6 F M) 2SD400(F) KTC3199-GR-AT/P E C B G D S B C E E C B NJM4558M(TE1) LD1117V KIA358F-EL TL3472CDR LTV817MCF 1: A 2: K 3: E 4: C 1: Vin...
MECHANICAL PARTS LIST [LD195SSX] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read BAG POLYETHYLENE 235X365XT0.03 0EM408420A carefully the product safety notice in this service...
Page 83
MECHANICAL PARTS LIST [LD195EMX] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read BAG POLYETHYLENE 235X365XT0.03 0EM408420A carefully the product safety notice in this service OWNERS MANUAL A94N4UH 1EMN24759 manual.
Page 84
MECHANICAL PARTS LIST [19MD359B/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read BAG POLYETHYLENE 235X365XT0.03 0EM408420A carefully the product safety notice in this service OWNERS MANUAL A94N0UH 1EMN24399 manual.
Page 85
MECHANICAL PARTS LIST [LD190EM1] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. STAND BAG A81N0UH 1EM425888 Before replacing any of these components, read ACCESSORIES carefully the product safety notice in this service BAG POLYETHYLENE 235X365XT0.03 0EM408420A manual.
Page 86
MECHANICAL PARTS LIST [19MD350B/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. SET BAG A81N0UH 1EM323958 Before replacing any of these components, read SERIAL NO. LABEL A01PBUH ---------- carefully the product safety notice in this service STAND BAG A81N0UH 1EM425888 manual.
Page 87
MECHANICAL PARTS LIST [LD190SS1] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. SET BAG A81N0UH 1EM323958 Before replacing any of these components, read SERIAL NO. LABEL A01PBUH ---------- carefully the product safety notice in this service STAND BAG A81N0UH 1EM425888 manual.
ELECTRICAL PARTS LIST [LD195SSX] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 89
Ref. No. Description Part No. Ref. No. Description Part No. C910 ELECTROLYTIC CAP . 47µF/25V M CE1EMASDL470 CN102 242 SERIES CONNECTOR 224202108W1 J322C08TG001 C911 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 C912 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A...
Page 90
Ref. No. Description Part No. Ref. No. Description Part No. D650 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 IC803 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC901 IC LD1117V NSZBA0SSS046 D653 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC902 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D654 DIODE FR154...
Page 91
Ref. No. Description Part No. Ref. No. Description Part No. GLASS GLAZE RES. 1/2W J 1M Ω Q1017 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R601# RXX2JZLZ0105 CEMENT RES. 3W K 1.2 Ω Q1018 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P R602 RW031R2PG007 RES CARBON FILM T 1/4W J 560k Ω Q1019 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P...
Page 92
Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 1.0k Ω CHIP RES. 1/10W J 100k Ω R686 RRXAFR5H1001 R941 RRXAJR5Z0104 RES CARBON FILM T 1/4W J 1.0 Ω CHIP RES. 1/10W J 100k Ω R688 RCX41R0T1001 R942...
Page 93
Ref. No. Description Part No. Ref. No. Description Part No. RES CARBON FILM T 1/4W J 100k Ω R1074 RCX4104T1001 TU302 TUNER UNIT ATSC/NTSC/QAM TDAU4-D02A UTUNNTUAL052 CHIP RES. 1/10W F 100k Ω R1081 RRXAFR5H1003 JACK ASSEMBLY CHIP RES. 1/10W F 68k Ω R1082 RRXAFR5H6802 CHIP RES.
Page 94
Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 100k Ω R711 RRXAJR5Z0104 JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 CHIP RES. 1/10W J 100k Ω R712 RRXAJR5Z0104 JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 CHIP RES.
Page 95
JUNCTION-A CBA(MJC-C) Ref. No. Description Part No. JUNCTION-A CBA(MJC-C) ---------- Consists of the following: CONNECTOR CN101 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 MISCELLANEOUS CL101 WIRE ASSY 8PIN 8PIN 100MM WX1A94N0-001 JUNCTION-B CBA(MJC-D) Ref. No. Description Part No. JUNCTION-B CBA(MJC-D) ---------- Consists of the following: CONNECTOR CN862B...
Page 96
ELECTRICAL PARTS LIST [LD195EMX] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 97
Ref. No. Description Part No. Ref. No. Description Part No. C910 ELECTROLYTIC CAP . 47µF/25V M CE1EMASDL470 CN102 242 SERIES CONNECTOR 224202108W1 J322C08TG001 C911 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 C912 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A...
Page 98
Ref. No. Description Part No. Ref. No. Description Part No. D650 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 IC631 IC LD1117V NSZBA0SSS046 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC801 AUDIO AMP IC TDA1517P/N3 112 NSCA0SNXP003 D653 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC803 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D654 DIODE FR154...
Page 100
Ref. No. Description Part No. Ref. No. Description Part No. METAL OXIDE FILM RES. 1W J 3.3 Ω CHIP RES. 1/10W J 10k Ω R684 RN013R3ZU001 R935 RRXAJR5Z0103 CHIP RES. 1/10W F 620 Ω CHIP RES. 1/10W J 10k Ω R685 RRXAFR5H6200 R936...
Page 101
Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 4.3k Ω R1071 RRXAFR5H4301 TM601 EYELET TYPE D-1 0VM406868 CHIP RES.(1608) 1/10W 0 Ω R1072 RRXAZR5Z0000 TM602 EYELET TYPE D-1 0VM406868 CHIP RES. 1/10W F 1.2k Ω R1073 RRXAFR5H1201 T1002#...
Page 102
Ref. No. Description Part No. Ref. No. Description Part No. Q774 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC771 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 Q841 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC841 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 RESISTORS JK711 JACK HPEP SML PCB S PJ-358H JXSJ020YUQ01 CHIP RES. 1/10W J 100k Ω JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02...
Page 103
Ref. No. Description Part No. RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 JUNCTION-A CBA(MJC-C) Ref. No. Description Part No. JUNCTION-A CBA(MJC-C) ---------- Consists of the following: CONNECTOR CN101 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 MISCELLANEOUS CL101 WIRE ASSEMBLY 8PIN 8PIN 100MM WX1A94N0-001 JUNCTION-B CBA(MJC-D) Ref.
Page 104
ELECTRICAL PARTS LIST [19MD359B/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 105
Ref. No. Description Part No. Ref. No. Description Part No. C910 ELECTROLYTIC CAP . 47µF/25V M CE1EMASDL470 CN102 242 SERIES CONNECTOR 224202108W1 J322C08TG001 C911 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN201 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007 C912 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A...
Page 106
Ref. No. Description Part No. Ref. No. Description Part No. D650 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 IC631 IC LD1117V NSZBA0SSS046 D651 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC801 AUDIO AMP IC TDA1517P/SOT398-1/18 NSCA0SNXP003 D653 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC803 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 D654 DIODE FR154...
Page 108
Ref. No. Description Part No. Ref. No. Description Part No. METAL OXIDE FILM RES. 1W J 3.3 Ω CHIP RES. 1/10W J 10k Ω R684 RN013R3ZU001 R935 RRXAJR5Z0103 CHIP RES. 1/10W F 620 Ω CHIP RES. 1/10W J 10k Ω R685 RRXAFR5H6200 R936...
Page 109
Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 4.3k Ω R1071 RRXAFR5H4301 TM601 EYELET TYPE D-1 0VM406868 CHIP RES.(1608) 1/10W 0 Ω R1072 RRXAZR5Z0000 TM602 EYELET TYPE D-1 0VM406868 CHIP RES. 1/10W F 1.2k Ω R1073 RRXAFR5H1201 T1002#...
Page 110
Ref. No. Description Part No. Ref. No. Description Part No. Q774 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC771 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 Q841 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P BC841 CHIP INDUCTOR BK1608HS601-T LLC601NTU017 RESISTORS JK711 JACK HPEP SML PCB S PJ-358H JXSJ020YUQ01 CHIP RES. 1/10W J 100k Ω JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02...
Page 111
Ref. No. Description Part No. RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 JUNCTION-A CBA(MJC-C) Ref. No. Description Part No. JUNCTION-A CBA(MJC-C) ---------- Consists of the following: CONNECTOR CN101 242 SERIES CONNECTOR TUC-P08X-B1 WHT JCTUB08TG002 MISCELLANEOUS CL101 WIRE ASSEMBLY 8PIN 8PIN 100MM WX1A94N0-001 JUNCTION-B CBA(MJC-D) Ref.
Page 112
ELECTRICAL PARTS LIST [LD190EM1] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 113
Ref. No. Description Part No. Ref. No. Description Part No. C833 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 C1054 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C906 CHIP CERAMIC CAP .(1608) CH J 390pF/50V CHD1JJ3CH391 C1056 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C907 CHIP CERAMIC CAP .(1608) CH J 390pF/50V...
Page 119
Ref. No. Description Part No. RES CARBON FILM T 1/4W J 220 Ω R950 RCX4221T1001 R951 WIRE CP STP-S-0.50 XZ40F0REN001 CHIP RES. 1/10W F 2.2k Ω R952 RRXAFR5H2201 CHIP RES. 1/10W F 2.2k Ω R953 RRXAFR5H2201 CHIP RES. 1/10W F 10k Ω R956 RRXAFR5H1002 SWITCHES...
Page 120
ELECTRICAL PARTS LIST [19MD350B/F7] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 121
Ref. No. Description Part No. Ref. No. Description Part No. C833 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 C1054 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C906 CHIP CERAMIC CAP .(1608) CH J 390pF/50V CHD1JJ3CH391 C1056 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C907 CHIP CERAMIC CAP .(1608) CH J 390pF/50V...
Page 127
Ref. No. Description Part No. RES CARBON FILM T 1/4W J 220 Ω R950 RCX4221T1001 R951 WIRE CP STP-S-0.50 XZ40F0REN001 CHIP RES. 1/10W F 2.2k Ω R952 RRXAFR5H2201 CHIP RES. 1/10W F 2.2k Ω R953 RRXAFR5H2201 CHIP RES. 1/10W F 10k Ω R956 RRXAFR5H1002 SWITCHES...
Page 128
ELECTRICAL PARTS LIST [LD190SS1] PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C604 POLYESTER FILM CAP . (PB FREE) 0.039µF/ CA2A393DT018 100V J Before replacing any of these components, read C605 POLYESTER FILM CAP .
Page 129
Ref. No. Description Part No. Ref. No. Description Part No. C833 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 C1054 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C906 CHIP CERAMIC CAP .(1608) CH J 390pF/50V CHD1JJ3CH391 C1056 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C907 CHIP CERAMIC CAP .(1608) CH J 390pF/50V...
• 2009-06-09 Changed the Part Number of “DVD MAIN CBA UNIT” on page 18-17 • 2010-03-11 LD190EM1 added • 2010-04-01 19MD350B/F7 added • 2010-04-01 LD190SS1 added • TBD LD195SSX, LD195EMX, 19MD359B/F7 Individual parts numbers added for the JACK ASSEMBLY 19-1 FL9.3REV...