Yaesu VX-5R Operating Manual page 32

Set Mode
Set Item 4 [ICON]
Function : ICON selection .
T
Recall Menu Item 3, then press the
[BAND(SET)AR]
key momentarily.
Q2
Turn the DIAL
to select the desired band or mode on which
you wish to utilize an
Icon, then press the
[BAND(SET)AR]
key momentarily.
~3
Turn the DIAL
to select the desired Icon to be displayed in place
of the regular indica-
tor.
® Press the PTT key momentarily to save the your new setting and
exit to normal opera-
tion .
Set Item 5
[VF01
Function : Select or disable the VFO Band edge for the current band .
Available Values : ALL/BAND
Default : BAND
ALL :
When the VFO frequency reaches the high edge of
the current band, the VFO
frequency will jump to the low band edge of
the next band (or vice versa) .
BAND : When the VFO frequency reaches the high
band edge of the current band, the
VFO frequency will jump to the low band
edge of the current band (or vice versa) .
Set Item 6 [ARS]
Function : Enable/disable the Automatic
Repeater Shift function .
Available Values : ON/OFF
Default : ON
Set Item 7 [RPT SHIFT]
Function : Set the Repeater Shift Direction
Available Values : -RPT/+RPT/SIMP
Default : Depends on the transceiver version .
Set Item 8
[SHIFT]
Function : Set the magnitude of the Repeater
Shift .
Available Values : 0 .00 - 99 .95 MHz
Default : Depends on the transceiver version, as well
as the setting of Menu #06 (ARS) .
Set Item 9 [VFO SPLIT]
Function : Enable/disable "VFO Split" Operation
Available Values : ON/OFF
Default : OFF
When this feature "ON," you can operate in a "split" mode between the
Main and Sub
VFO frequencies (the Main VFO will be used for Rx, while
the Sub VFO will be used for
Tx) .
VX-SR OPERATING MANUAL
u
Set Item 10 [VFO LINK]
Function : Enable/disable the VFO Link
feature .
Available Values : ON/OFF
Default : OFF
When this feature "ON," the Main and Sub
VFOs are "slaved" so that they change 1
quency together.
Set Item 11 [VFO STEP]
Function : Setting of the synthesizer steps .
Available Values : 5/9/10/12 .5/15/20/25/50/100 kHz
Default : Depends on the transceiver version .
Set Item 12 [RESUME]
Function : Select the Scan Resume mode .
Available Values : 5 SEC/BUSY/HOLD
Default : 5 SEC
5 SEC : The scanner will hold for 5 seconds, then resume
whether or not the other star
is still transmitting .
BUSY: The scanner will hold until the signal disappears,
then will resume when the c
rier drops .
HOLD : The scanner will stop when a signal
is received, and will not restart .
Set Item 13 [SCAN LAMP]
Function : Enable/disable the Scan lamp while paused .
Available Values : ON/OFF
Default : ON
Set Item 14 [RX SAVE]
Function : Select the Receive-mode Battery Saver interval
("sleep" ratio) .
Available Values : OFF/200mS(1 :1)/300mS(1 :1
.5)/500mS(1 :2 . 5 )/ls( 1 :5 )/ 2 s(l :10 )
Default : 200mS(I :1)
Set Item 15 [TX SAVE]
Function : Enable/disable The Transmit Battery Saver.
Available Values : ON/OFF
Default : OFF
Set Item 16 [APO]
Function : Set the Automatic Power-Off time .
Available Values : OFF/30 min/1 hour/3 hours/5
hours/8 hours
Default : OFF
VX-SR OPERATING MANUAL
Set Mod