Viewing Pictures From The Connected Equipment - Sony TH-37PWD6UY Operating Instructions Manual

Viewing pictures from the connected equipment

Turn on the connected equipment, then press
Press F/f to select the desired input source, then press
2 seconds pass without any operation after pressing F/f.) When the input source is set to "Skip"
in the "Video Labels" under the "AV Set-up" menu (page 26), that input does not appear in the
list.
z • Press / on the top edge of the TV to display the connected equipment list and select the desired input source. You
can also press F/f to select the desired input source. Then wait for 2 seconds to display the selected input source.
Jacks/
Input symbol on screen
A HDMI IN 2
I HDMI IN 1 or 3
HDMI 1 or
HDMI 2 or
HDMI 3
B
2, and 2
Video 2
C i
D
1 or 1 or 3,
and 1 or 3
Video 1 or
Video 1 or
Video 3
E
/
F
/ 1 or 2
HD/DVD 1 or
HD/DVD 2
G
H PC IN
(RGB)/
PC
16
GB
Description
Connect to the HDMI IN 1, 2 or 3 jack if the equipment has an HDMI jack. The digital
video and audio signals are input from the equipment. In addition, when you connect
the equipment that is compatible with control for HDMI, communication with the
connected equipment is supported. Refer to page 27 to set-up this communication. If
the equipment has a DVI jack, connect the DVI jack to the HDMI IN 3 jack through a
DVI - HDMI adaptor interface (not supplied), and connect the equipment's audio out
jack to the audio in jack in the HDMI IN 3 jack.
~ • The HDMI jacks only support the following video inputs: 480i, 480p, 576i, 576p, 720p
(50/60 Hz), 1080i (50/60 Hz), 1080p (50/60 Hz) and 1080/24p.
• Be sure to use only an HDMI cable that bears the HDMI logo (recommended Sony
HDMI cable).
• When connecting an audio system with HDMI jack, be sure to also connect to the audio
(refer G in page 15) to listen to the sound from the TV on audio
output jacks
system.
Connect to the video jack
equipment, connect to the L(MONO) jack
Connect to the i jack to listen to sound from the TV on headphones.
Connect to the S video jack
1 or 3. To avoid picture noise, do not connect the camcorder to the video jack
and the S video jack
to the L(MONO) jack
Connect to the video output jack
audio output jacks to record the sound from the TV on DVD recorder or VCR. To
turn off the sound of the TV speakers, set "Speaker" to "Audio System" (page 27). If
you connect mono equipment, connect to the L jack
~ • The monitor output jacks cannot support HD/DVD, HDMI and PC signals source
pictures, also digital audio signal for sound.
Connect to the component jacks and the audio jacks
quality, component connection is recommended if your DVD player has a component
video output.
Connect to the audio output jacks
equipment. To turn off the sound of the TV speakers, set "Speaker" to "Audio System"
(page 27).
Connect to the PC IN
use a PC cable with ferrite.
/ to display the connected equipment list.
. (The highlighted item is selected if
2, and the audio jacks
2.
1 or the video jack
1 at the same time. If you connect mono equipment, connect
1 or 3.
to record the image from the TV. Connect to the
to listen to the sound from the TV on Hi-Fi audio
(RGB) jack and the audio jack
2. If you connect mono
1 or 3, and the audio jacks
.
/ 1 or 2. For better picture
. It is recommended to
1