Advertisement
DRYER VENTING RECOMMENDATIONS
4-WAY VENTING KIT
Call Sears Parts 1–800-225-2864
38020
26-98379 — Vent Hood
Aluminum body and plastic
molded hood with a 4" opening.
Clamps are recommended for wall
and dryer connections. Steel clamps
designed to resist stretching, with
phillips/hex head screw are included
one each on elbows and periscopes.
IMPORTANT NOTE:
Do not use non-metal flexible duct. Also, when installing the venting system, do not exceed
the specified length for the vent duct. Venting systems which are longer than specified will
accumulate lint, increase drying time and energy use and shorten the life of the dryer.
POWER CORDS FOR ELECTRIC DRYERS ONLY
26-49387, 26-49787
All Electric Dryers Require Cord
Order
26-49387
26-49787
26-49388*
26-49788*
*Complies with 1/1/96 NEC code revision for new construction and remodeling
WASHER AND DRYER DIMENSIONS / OPTIONAL PEDESTALS / STACKING KITS
Washer Dimensions W x H x D
Washer
(Depth with Door Open)
26-41272
27 x 38
11
29
3
(50
13
/
16 x
/
/
4
16
INSTALLATION OPTIONS
CLEARANCES
Most installations require a minimum 5
1
/
in. clearance behind
2
the dryer for the exhaust ducting. Allow minimum clearances of
at least 1 in. on the sides and back to minimize vibration and
noise. Allowing additional clearance for installation and servicing
is recommended. Be sure to allow for wall, door, or floor moldings
that may increase the required clearances. Allow at least 21" in
front of the dryer to open the door.
CLOSET INSTALLATION
The closet door must allow for sufficient airflow. Refer to the
diagram for minimum vent opening requirements. A louvered
door is also acceptable.
20
1
/
"
4
4"
1"
30
1
/
"
4
50
1
/
"
2
Due to Sears policy of continuous improve ment on its products, Sears reserves
the right to change materials and specifications without notice. Before installing,
consult installation instructions packed with product. For complete warranty
information, consult the owner's manual or visit www.managemylife.com.
VENT HOOD TYPE
Number of
90° Elbows
4"
0
65 ft.
1
55 ft.
2
47 ft.
3
36 ft.
4
28 ft.
4" Clearance Behind the Dryer is Preferred for Best Airflow.
2" Clearance is Achieved With Periscopes.
26-49388, 26-49788
Wire
Length
3
4 ft.
3
6 ft.
4
4 ft.
4
6 ft.
Dryer Dimensions W x H x D
Dryer
(Depth with Door Open)
26-8/91272
)
27 x 39
29
9
(49
4
x
/
/
10
IMPORTANT NOTE:
If you are installing your dryer
using an optional pedestal
base or stacking kit, please
refer to the instructions for your
pedestal or stacking kit before
proceeding with the installation.
Closet Door Vent Requirements
1"
27"
4"
2
1
/
"
2
65 ft.
55 ft.
55 ft.
47 ft.
Max. Length
of 4" Dia.
47 ft.
41 ft.
Rigid Heavy
36 ft.
30 ft.
Metal Vent
28 ft.
22 ft.
BOTTOM / SIDE
VENTING KIT
26-49670
LP DRYER KIT
26-17025
Gas Dryer Connector – Stainless Steel
26-49590
26-49585*
*Los Angeles only
Color
Stacking Kit
)
White
26-17013
5
INSTALLATION WITH PEDESTAL
52
1
/
"
2
30
3"
Vent
48 sq. in.
Vent
24 sq. in.
3"
26-81272, 26-91272
4" CLEARANCE BEHIND DRYER
26-49900 — Over-The-Top
Kit
™
Universal solution, 8 foot length. Kit includes
two 4 ft. pipe sections with attached elbows,
two close elbows, clamps and wall plate.
26-49608 — Flexible Pipe
4" x 6' with snap-lock fittings, 90˚ turn takes
1 foot length and 6 inch clearance.
26-49609 — Close Elbow
Turns 90˚ within 4", rotating collars and
snap-lock fittings.
2" CLEARANCE BEHIND DRYER
26-49908 — Periscope 0-18"
For outlets that overlap or are very close
26-49904 — Periscope 18-29"
Reaches side of most dryers
26-49905 — Periscope 29-50"
Reaches top of most dryers
1
/
" -
3
/
" Flex, 5 ft.
2
8
3
/
" -
3
/
" Flex, 5 ft.
8
8
Pedestal
Pedestal Dimensions W x H x D
26-51022 (with Drawer)
27 x 13.6
28.4
x
INSTALLATION WITH
STACKING KIT
1
/
"
4"
4
1"
27"
26-81272.PDF
Page 2 of 2
6"
76"
1"
Effective 05/14/12
Advertisement
