KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 1 Safety Precautions 1.1. For Service Technicians ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil and ground them. 2. Ground the soldering irons.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 2.2.1. Suggested PbF Solder There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper (Sn+Ag+Cu), you can also use Tin and Copper (Sn+Cu) or Tin, Zinc, and Bismuth (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with other materials.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.2. Circuit Operation (Base Unit) 4.2.1. Outline Base Unit consists of the following ICs as shown in Block Diagram (Base Unit) (P.7). • BBIC (Base Band IC): IC1 - Handling all the audio, signal and data processing needed in a FHSS base unit...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.2.3. Telephone Line Interface <Function> • Bell signal detection • Clip signal detection • ON/OFF hook circuit • Audio circuits • DTMF tone signal circuits Bell signal detection: In the standby mode, Q104 is open to cut the DC loop current and decrease the ring load.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.4. Circuit Operation (Handset) 4.4.1. Construction The circuit mainly consists of DSP and RF part as shown in the block diagram. 4.4.1.1. BBIC: IC1 Function: • Battery Low, Power down detect circuit • Ringer Generation • Interface circuit (RF part, Speaker, Mic, LED, Key scan, LCD) Initial waves: 4.4.1.2.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.4.2. Power Supply Circuit Circuit Operation: When power on the handset, the voltage is as follows; BATTERY (2.2 V ~ 2.6 V: J1) → L502 → L300, D300 → Q300 (3.4 V) → Q302 (1.8 V), Q301 (2.5 V)
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.4.3. Charge Circuit Circuit Operation: When charging the handset on the charger unit, the charge current is as follows; DC+ (6.5V) → R304, R305, R309, R310 → CHARGE+ (Base) → CHARGE+ (Handset) → Q502 → D501 → L502 →...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 4.4.5. Sending Signal 4.4.6. Battery Low/Power Down Detector Circuit Operation: “Battery Low” and “Power Down” are detected by BBIC which check the voltage from battery. The detected voltage is as follows; • Battery Low Battery voltage: V (Batt) < 2.3V ± 50mV The BBIC detects this level and “...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 7 Operation Instructions 7.1. Guide to Cordless Handset Programming 7.1.1. Programming by Scrolling through the Display Menus...
Page 22
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 7.1.2. Programming Using the Direct Commands...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 7.2. Dial Lock For Service Hint: *: If the current password is forgotten, enter “726276642” and you will be able to go to the next step.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 9 Service Mode 9.1. Copying Phonebook Items When Repairing...
Page 33
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS Note: • If the max number of handsets are already registered to the base unit, a new handset cannot be registered. • To register the handset, refer to Registering the Cordless Handset (P.24) • To cancel the handset, refer to Canceling the Cordless Handset Registration (P.24)
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.1.1. Check Power 10.1.1.1. Base Unit Is the AC Adaptor inserted into AC outlet? (*1) Cross Reference: Note: Power Supply Circuit (P.8) (*1) Refer to Specifications (P.6) for part number and supply voltage of AC Adaptor. 10.1.1.2. Handset Cross Reference:...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.1.2. Check Battery Charge 10.1.2.1. Base Unit Cross Reference: Charge Circuit (P.13) Note: (*1) Refer to Specifications (P.6) for part number and supply voltage of AC adaptor. 10.1.2.2. Handset 10.1.2.3. Charger Unit Note: (*1) Refer to Specifications (P.6) for part number and supply voltage of AC adaptor.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.1.3. Check Link 10.1.3.1. Base Unit Cross Reference: Check Point (Base Unit) (P.40) Power Supply Circuit (P.8) 10.1.3.2. Handset Cross Reference: Power Supply Circuit (P.12) Adjustment of Handset (P.52)
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.1.4. Check Handset Transmission Cross Reference: Signal Route (P.15) 10.1.5. Check Handset Reception Cross Reference: How to Check the Speaker or Receiver (P.55). Signal Route (P.15) 10.1.6. Check Caller ID Cross Reference: Signal Route (P.15) 10.1.7. Bell Reception 10.1.7.1. Base Unit 10.1.8.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.2. Troubleshooting by Symptom (Base Unit ) If your unit has below symptoms, follow the instructions in remedy column. Note: (*1) Refer to Check Point (Base Unit) (P.40) 10.2.1. Check Point (Base Unit) Please follow the items below when BBIC or FLASH is replaced.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.3. How to Replace the Flat Package IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 10.3.3. How to Install the IC 1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins. *Check the accuracy of the IC setting with the corresponding soldering foil. 2. Apply flux to all pins of the FLAT PACKAGE IC.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12 Measurements and Adjustments 12.1. Things to Do after Replacing IC Important: Please execute the adjustment process when you replace the following object parts. 12.1.1. Base Unit Necessary Adjustment BBIC CPU, interface for RF and FlashROM. 1. BandGAP adjustment (IC1) 2.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.2. The Setting Method of JIG (Base Unit) 12.2.1. Preparation 12.2.1.1. Equipment Required • Frequency counter: It must be precise enough to measure intervals of 1 Hz (precision; ±4 ppm). Hewlett Packard, 53131A is recommended. • Digital multi-meter (DMM): It must be able to measure voltage and current.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.2.2.2. Batch file Settings Note: • “****” varies depending on the country. • Refer to Commands (P.51) for frequently used commands.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.3. The Setting Method of JIG (Handset) 12.3.1. Preparation 12.3.1.1. Equipment Required • Frequency counter: It must be precise enough to measure intervals of 1 Hz (precision; ±4 ppm). Hewlett Packard, 53131A is recommended. • DC power: It must be able to output at least 1 A current under 2.4 V for handset.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.3.2.2. Batch file Settings Note: • “****” varies depending on the country. • Refer to Commands (P.51) for frequently used commands. 12.4. Commands Command name Function Example getver Check software version Type “getver”, then registered software version is read out.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.6. Base Unit Reference Drawing When connecting the simulator equipments for checking, please refer to below. 12.6.1. Flow Solder Side View...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 12.8. How to Check the Speaker or Receiver 1. Prepare the digital voltmeter, and set the selector knob to ohm meter. 2. Put the probes at the speaker terminals as shown below.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 13 Schematic Diagram 13.1. For Schematic Diagram 13.1.1. Base Unit (Schematic Diagram (Base Unit)) Notes: 1. DC voltage measurements are taken with voltmeter from the negative voltage line. 2. The schematic diagrams may be modified at any time with the development of new technology.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 15 Appendix Information of Schematic Diagram 15.1. CPU Data (Base Unit) 15.1.1. BBIC (IC4) Description High High_Z key Scan Key in I-PU Description High High_Z key Scan Key in I-PU Digital Source 3.0V VDD Non use Digital GND SP-AMP_CD Digital Source 3.0V VDD...
Page 74
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS Description High High_Z 105 REG2 control 106 Power Source INPUT 107 CID Signal INPUT Analog Analog 108 Analog GND 109 1.8V +1.8 110 LINE OUT Analog Analog 111 CID REF 112 CID Signal INPUT Analog Analog 113 CID AMPO...
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 15.2. CPU Data (Handset) 15.2.1. IC1 (BBIC) PIN Description High High_Z 41 Mode control/ RST↑: RST↑: I-PU PIN Description High High_Z UART TX data usually Boot mode Key Scan key in I-PU mode Digital IO Source 42 UART RX data I-PU 2.5V...
Page 76
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS PIN Description High High_Z 79 Charge current monitor 80 NC Note: • The mark “*” in the I/O column means the port is controlled by the firmware.
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS 16.2. Cabinet and Electrical Parts (Handset) Note: (*1) Attach the spacer (No. 109) to the exact location described above.
Ref. Part No. Part Name & Description Remarks SA101 J0LF00000026 VARISTOR (SURGE ABSORBER) SA102 J0LE00000047 VARISTOR (SURGE ABSORBER) PQGT18973Z NAME PLATE (for KX-TG2853BXS) (RESISTORS) PQGT18972Z NAME PLATE (for KX-TG2854BXS) ERJ2GEJ102 PQHA10011Z RUBBER PARTS, FOOT CUSHION ERJ2GEJ101 PQKF10702Y1 CABINET COVER PS-HB...
Page 85
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ERJ2GEJ102 C181 ERJ6GEY0R00 ERJ2GEJ103 ERJ2GE0R00 ERJ2GEJ103 ERJ2GEJ103 ERJ2GEJ102 (CAPACITORS) ERJ2GEJ102 ECUV1A224KBV 0.22 R103 ERJ3GEYJ104 100K ECJ0EB1C103K 0.01 R105 PQ4R10XJ272 2.7K ECJ0EB1C103K 0.01 R106...
Page 86
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C763 ECJ0EC1H100D C765 ECJ0EC1H150J PCB100 PFWPG2853BXR MAIN P.C.BOARD ASS'Y (RTL) C766 ECJ0EC1H100D (ICs) C767 ECJ0EC1H151J 150P PFWI12853BXR IC (*1) C768 ECJ0EC1H100D PFWI22853BXR IC (*1)
Page 87
C302 F2G0J3310025 (*1) You can download and refer to the Operating Instruc- C303 F2G0J3310025 tions (Instruction book) on TSN Server. C304 F1K0J226A004 C305 ECUV1A105KBV 16.5.4.1. KX-TG2853BXS C306 ECUV1A105KBV C307 ECUV1A105KBV C308 ECUV1A105KBV Ref. Part No. Part Name & Description Remarks...
Page 88
KX-TG2853BXS/KX-TG2854BXS/KX-TGA280BXS Ref. Part No. Part Name & Description Remarks PQQW15151Z LEAFLET, QUICK GUIDE (for Arabic) PQQW15152Z LEAFLET, QUICK GUIDE (for Persian) XZB21X35A03 PROTECTION COVER (for Base Unit) XZB10X35A02 PROTECTION COVER (for Hand- set) PQPK15381Z GIFT BOX 16.5.4.2. KX-TG2854BXS Ref. Part No.