Warnings, Cautions, and Notes ............2 1.2.1. General Warnings and Cautions ............3 1.2.2. General Rules for Use of the Masterdock ..........3 1.3. Warranty Statement ................4 1.3.1. Contacting Scott Health & Safety ............4 ...
Page 4
Masterdock Docking Station Instruction Manual This Page Left Intentionally Blank P/N 087-0045 Rev. E 01/10...
Page 5
Masterdock Docking Station Instruction Manual List of Figures Figure 2-1. Masterdock Components ................8 Figure 3-1. Masterdock Wall Mounting Dimensions ............. 9 Figure 3-2. Installing Calibration Gas ................. 10 Figure 3-3. Installing SD Memory Card ..............11 Figure 4-1. Masterdock Utility Main Display ............... 15 Figure 4-2.
Page 6
Masterdock Docking Station Instruction Manual This Page Left Intentionally Blank P/N 087-0045 Rev. E 01/10...
Page 7
Masterdock Docking Station Instruction Manual List of Tables Table 1-1. Acronym Quick Reference List ..............5 Table 2-1. Masterdock Components ................8 Table 4-1. Status LED Indications................13 Table 5-1. Parts List ....................19 Table 5-2. Troubleshooting Chart ................20...
Page 8
Masterdock Docking Station Instruction Manual Record of Revisions Revision Date Description 04/09 Initial release 08/09 Updated LED indications and troubleshooting table 09/09 Updated P/N's 10/09 Updated P/N's 01/10 Updated Table 4-1 and 5-2. viii P/N 087-0045 Rev. E 01/10...
FOLLOW THESE INSTRUCTIONS MAY ALSO RESULT IN SERIOUS INJURY OR DEATH 1.1. Important Notices Scott Health and Safety can take no responsibility for use of its equipment if it is not used in accordance with the instructions. If further operational or maintenance details are required but not provided in this manual, contact Scott Health and Safety or their agent.
Masterdock Docking Station Instruction Manual 1.2. Warnings, Cautions, and Notes Throughout this document, warnings, cautions, and notes have been interspersed to draw attention to potentially unsafe, hazardous, or unique situations that require user attention. Each warning, caution, or note is labeled and quickly identified using an icon.
Instruction Manual 1.2.1. General Warnings and Cautions The following list of warnings and cautions pertain to the general use and care of the Masterdock. Failure to follow these warnings and cautions may result in death, injury, or poor equipment performance.
DOCKING STATION (THE PRODUCTS) to be free from defects in workmanship and materials for a period of one (1) year from the date of original manufacture by SCOTT. This warranty applies to all components of THE PRODUCTS supplied at the time of original sale of THE PRODUCTS. SCOTT’s obligation under this warranty is limited to replacing or repairing (at SCOTT’s option) THE...
Masterdock Docking Station Instruction Manual 1.4. Acronyms Quick Reference Throughout the duration of this manual, several acronyms are used. Provided in Table 1-1 is a quick reference chart to quickly identify any acronym that may be unfamiliar to users. Table 1-1.
Page 14
Masterdock Docking Station Instruction Manual This Page Left Intentionally Blank 6 of 20 P/N 087-0045 Rev. E 01/10...
Protégé units simply by docking a Protégé into the Masterdock and pressing a button. The Masterdock can be used on any flat surface such as a desk top, or can be mounted on a wall. Wall-mounting instructions are included in this guide.
Masterdock Docking Station Instruction Manual Figure 2-1. Masterdock Components Table 2-1. Masterdock Components Number Component Number Component Air Outlet Bump and Calibration Activation Buttons Calibration Gas Gauge Calibration Gas Dock Status LEDs Air Inlet Protégé Dock Air Filter Battery Cover (On Side of Unit)
3.1. Mounting the Masterdock The Masterdock does not need to be mounted on a wall to operate. It may be placed on any desk top, table top, or other horizontal surface and will operate. However, users may choose a more permanent location, such as mounted on a wall.
Refer to Figure 3-1 for the location of the AC power connection. The battery compartment is located on the side of the Masterdock. Push up on the tab and then pull up on the door to remove the cover. Rechargeable batteries may be used; however, the Masterdock will not recharge those batteries when connected to an external source.
To install the SD card, open the cover found on the bottom of the Masterdock next to the USB connection. Verify the SD card is unlocked prior to installation. Slide the SD card into the slot fully until it clicks and close the cover.
3.4.1. Formatting an SD Card If the Service Requested LED blinks orange on the Masterdock or if you are using a new SD card for the first time, the SD card may need to be formatted. The Masterdock does not automatically format a card, it must be formatted using a PC.
4. Operation 4.1. Bump Testing and Calibration Prior to performing any bump test or calibration, the Protégé unit and the Masterdock must be powered on. Verify the Battery LED is green on the Masterdock and the pressure gauge indicates greater than 50 psi. Ensure the air inlet is not obstructed and the filter is clean.
User Mode are available in Administrator Mode. However, Administrator Mode also allows users to set the Gas Lot Number, set the Location, synchronize the Masterdock to the time on the PC, and configure the Masterdock to perform a calibration in the event of a bump test failure.
Figure 4-1. Masterdock Utility Main Display 4.3.4. Masterdock Utility Menus Four Menus are available for use in the Masterdock, Operation, Option, View, and Help. Not all selections will be available depending on which mode is selected. 15 of 20 P/N 087-0045 Rev. E 01/10...
Setup Port - Used to change the COM port. Refer to Paragraph 4.3.1 for more information. Get Configurations - Used to poll the Masterdock about current information for display including the Firmware Revision, Gas Lot Number, Serial Number, and Location of the Masterdock.
Masterdock Docking Station Instruction Manual 4.3.4.2. Option Menu Language - Used to Select which language for the Masterdock utility to display. Figure 4-3. Masterdock Utility Option Menu 4.3.4.3. View Menu Toolbar - Used to display or hide the Toolbar. Status Bar - Used to display or hide the Status Bar.
Masterdock Docking Station Instruction Manual 4.3.4.4. Help Menu About Masterdock Utility - Used to display the current software revision level of the Masterdock Utility. Figure 4-5. Masterdock Utility Help menu 18 of 20 P/N 087-0045 Rev. E 01/10...
ASTERDOCK AS THEY MAY LEAK OR CORRODE AND CAUSE DAMAGE TO COMPONENTS Clean the Masterdock as needed using only compressed air or a clean dry cloth. If needed, a dampened cloth may be used for external cleaning, however do not use any cleaners or solvents.
Pump does not operate docking station door to Protégé, or replace Obstructed line pump. Port has not been setup Masterdock Utility fails to open Refer to Paragraph 3.6 Paragraph COM port USB driver has not 4.3.
5.3. Scott Repairs For quick and effective service of your instrumentation, and to reduce time spent on repairs, the SCOTT Instruments Service Department requires a Return Maintenance Authorization number be issued prior to any product being shipped for service repairs.