Subscribe to Our Youtube Channel
Related Manuals for Robinsons Regent
Summary of Contents for Robinsons Regent
- Page 1 G R O W I N G B E T T E R T H R O U G H D E S I G N Regent · Royale · Rosette · Regal GREENHOUSE Assembly Instructions 04/02...
-
Page 2: Table Of Contents
Greenhouse Base Plan EXTERNAL DIMENSIONS (mm) We cannot emphasis how important it is to have a proper base for your Robinsons CONTENTS PAGE NO. Greenhouse to be erected upon. It is essential that the BASE IS FLAT, LEVEL AND MODEL... -
Page 3: General Order Of Assembly
General order of assembly 1. Assemble Roof 2. Assemble Sides with Roof 3. Assemble the Gable Ends 4. Assemble the Vent 5. Glaze the Roof 6. Fit Vent 7. Glaze the Sides 8. Glaze the Plain End 9. Glaze the Door End up to door aperture (not above) 10. -
Page 4: Assembly Of Roof Sides And Ends
ASSEMBLY OF ROOF, SIDES & ENDS NOTE: If fitting a partition or extension 6. Repeat process for the other side. read in conjunction with Pages 13. 7. Fit apex plate (No. 7, ID chart) to both ends as shown and NOTE: IDENTIFICATION OF ALL PARTS AND SECTIONS CAN BE FOUND ON THE ID Insert short square headed bolts (No. - Page 5 For Regent models no centre glazing bar is fitted. 14. Lifting one side of the roof assembly only, slide a centre intermediate glazing bar onto the previously fitted bolt in the eaves gutter.
-
Page 6: Assembling The Vent
26. Identify door end glazing bars (No. 2, ID Chart). Proceed as for plain end glazing bars, remembering On REGENT ONLY fit short purlin to left hand side of to slide an additional short bolt up each glazing bar. door end and temporarily fix the strike plate at this Do not at this stage fix the short centre glazing bar, stage. -
Page 7: Positioning The Vent
POSITIONING THE VENT position and screw down with self tapping screws. RIDGE CRESTING AND FINIALS NEED TO BE Totally secure the bar cap using self tapping screws. POSITIONED BEFORE GLAZING THE ROOF. NOTE: Before glazing it is advisable to Fit the bar cap cover (No.13, ID Chart) separate the various bar caps and ONLY ‘MALE’... -
Page 8: Glazing The Sides
GLAZING THE SIDES 43. With reference to the glazing plan identify glass, PVC 4mm separator corner bar capping, PVC standard bar capping (No. 14 and 15 ID Chart), 4mm separator strips for glass (No 25 ID Chart). 44. Bar capping will be almost the same length as side glazing bars. -
Page 9: Glazing The Ends
55. The Royale and Rosette models are both supplied with illustration, next column) double doors. The Regent differs having a single door, 59. Identify the track support cleat (No. 35, ID Chart) and the fitting procedures are similar, the main difference the track support (supplied but NOT required on being a strike plate for the single door (No. -
Page 10: Assembling The Doors
60. Offer up to the complete track assembly and attach 65. Select the bottom door crossbar (No. 41 ID Chart), to the track supports as shown, using long bolts. The position this between the side members and loosely door track should rest on the small ‘S’ shaped clips fix using pan head bolts. -
Page 11: Fitting The Doors
Nylon brush strip Inner side member + strike Outer side member + lock Glass Edging strip Side member ASSEMBLING THE DOORS 80. Check that both doors run freely, if not then check that the outer track is sitting squarely on the inner track. It may be that the centre door stop (Double doors only) Single door Double door... -
Page 12: Final Finishings
(5 for Rosette and Regal, 4 for Royale, and pipes, fit these at the down pipe end. Now fit the Corner 3 for Regent) to accommodate a reinforcing channel. glazing bar blanking grommets (No. 55, ID Chart) at the opposite Continue therefore erecting the main building frame, end. - Page 13 building and extension module, the reinforcing frame Eaves joint plates reinforcing normally fitted between two buildings is no longer channel Base rail used. It is imperative in this situation that the partition joint plate faces the main building. (See diagram). 92.
-
Page 14: Securing The Base
METHOD OF ERECTION: ROSETTE SECURING THE BASE WITH SOIL Glazing Bar Base bracket Rosette 10ft model - single door BASE ANCHORS. 94.Clad as for plain end. Because the door is plain (no 96. When the greenhouse is in its final position, identify Long bolt handle or lock fitted), it can be made to slide in either the soil base anchors (No. - Page 15 The Regal is Robinsons new 12ft (3836mm) wide SIZE REGAL 12 • greenhouse with lengths from 8ft (2632mm) upwards in 2ft (610mm) increments. There is no limit on the length. MODEL Normal size ‘A’ Frame Max Span 8 + 6 8’...
- Page 16 I.D. Chart 18. Vent hinge D866 1. Ridge 5. PVC glazing strip member 11. Door and D231 R118 plain end gable base rail R174 Door guide (door end only) 6. Short square headed D860 S/D, D861 D/D bolt F5002 nut F5006 12.
- Page 17 I.D. Chart 34. Doorway Header D864 S/D F5001 D865 D/D 24. Cropped head bolts F5006 30. Tubular Eaves Brace (450mm) 39. Door side 25. Separator Strip D126 and Roof tie (1015m) D128 member (outer) 4mm D101 D093 LH D094 RH 35.
- Page 18 I.D. Chart 52. Moulded door 60. Gutter joint plate track cover D158 D204 44. PVC 65. Eaves joint plate edging strip D146 D232 & D233 E-Ring 45. Top door 66. Re-inforcing D252 crossbar 53. Ridge finial D203 frame 25x25 D307 D136 61.
-
Page 19: Glazing Plans
TOUGHENED GLASS ONLY 4mm Glazing Plans Measurements in mm. REGENT Ref. 893 Ref. D1208 610 X 1070 Shape C Vent 610 X 610 Shape A Shape B Shape A Shape A Shape A Ref. D900 Shape A 610 X 470 Ref. - Page 20 TOUGHENED GLASS ONLY 4mm Glazing Plans Measurements in mm. Ref. D1208 Ref. D1216 ROSETTE 610 X 610 Shape E 610 X 1162 Shape Shape Ref. D902 Shape H Shape H Shape Shape Shape Shape D907 D907 Shape Shape Shape Shape Ref.
- Page 21 TOUGHENED GLASS ONLY 4mm Glazing Plans Measurements in mm. REGAL 12ft Glazing plan Shape J Shape Shape Shape Shape Ref. D890 Shape A Shape A 1374 1374 1374 1374 1374 1374 Shape K Ref. D891 610 X 305 610 X 305 610 X 305 610 X 305 610 X 305...
-
Page 22: Slat Staging Assembly Instruction
THREE 3-Slat - 11” · 28cm Deep Shelf Feed bolts as required into central groove on Joining two sections underside of slat. May be fixed to aluminium greenhouse glazing bars or The shelf may be easily extended as required by direct to a wall. -
Page 23: Slat Staging Assembly Instruction
THREE 7-Slat - 25” · 63.5cm Deep Shelf Fix the wall cleats using Secure slats to cropped-head bolts the horizontal May be fixed to aluminium greenhouse glazing bars or (ensuring that they are brackets as direct to a wall. correctly fully engaged in shown. -
Page 24: Slat Staging Assembly Instruction
THREE 10-Slat - 37” · 94cm Deep Shelf Fix the wall cleats using cropped- Secure slats to head bolts (ensuring that the horizontal May be fixed to aluminium greenhouse glazing bars or they are correctly fully brackets as direct to a wall. Extra support is supplied for this engaged in the nut shown. -
Page 25: Louvre Installation Instruction
Louvre Installation Instructions D361 Louvre Kit Exploded View No.6 x 12 screws INSTALLATION 1 Screw self-tapping screws through holes in the top and bottom cill members into the ‘C’ groove of the Top cill side jambs to form a complete frame. 2 From outside the greenhouse, fit the frame in place, fixing into position using the plastic bar caps and screws. -
Page 26: Plates Assembly Instruction
For Shelving or Staging which needs to be For Right Angle Joining of Slats slide square head reduced in length to clear a Robinsons bolts into Slat ‘A’ (one per slat to be joined). Partition/Sliding Door it is necessary to Slide one square head bolt (per Slats ‘B’) and... -
Page 27: A' Frame Assembly Instruction
‘A’ Frame Adaptor Assembly Instructions Shelving Staging When Shelving extends past or ends at an ‘A’ Staging extending past an ‘A’ Frame as drawn Fig. 2 Frame reinforcing channel. (see note E for ending at an ‘A’ Frame). Mounting Bracket 45mm Fix top slope bracket to horizontal bracket with 1. - Page 28 Whilst the information contained in this leaflet is accurate at the time of publication, changes in the course of Robinsons policy of improvement through development and design might not be indicated. We point out this fact to avoid any infringements of the Trade Descriptions Act and also to advise that Robinsons Greenhouses reserve the right to change specifications and materials without prior notice.
Need help?
Do you have a question about the Regent and is the answer not in the manual?
Questions and answers
Is there an easier way to fit the bar capping cover strips, rather than whacking them with a rubber mallet, which seems wrong, especially where the roof glass panes overlap? (Robinsons **** model)
To fit the bar capping cover strips more easily on the Robinsons Regent model without using a rubber mallet, apply a small amount of water or washing-up liquid to help the parts slide into place.
This answer is automatically generated
Can you buy a Robinson Regent Roof Vent already assembled