Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
Digital Camera
Contents
1. OUTLINE OF CIRCUIT DESCRIPTION .................... 3
2. DISASSEMBLY ........................................................ 11
3. ELECTRICAL ADJUSTMENT .................................. 16
REGISTRATION ...................................................... 21
5. TROUBLESHOOTING GUIDE ................................. 22
6. PARTS LIST ............................................................. 24
ELECTRICAL PARTS .............................................. 24
ACCESSORIES & PACKING MATERIALS ............. 27
CABINET & CHASSIS PARTS 1 ............................. 28
CABINET & CHASSIS PARTS 2 ............................. 30
CIRCUIT DIAGRAMS &
PRINTED WIRING BOARDS ...................................... C1
WARNING
This product has been manufactured using lead-free solder. Be sure to follow the warning given on page 2 when carrrying out
repair work.
The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part
designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.
CAUTION : Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.
NOTE : 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N. S. P. : Not available as service parts.
Design and specification are subject to change without notice.
SX813/U, EX, GX
PRODUCT SAFETY NOTICE
FILE NO.
VPC-S6U
(Product Code : 168 028 01)
(U.S.A.)
(Canada)
VPC-S6
(Product Code : 168 028 02)
(Europe)
(South America)
(China)
(Australia)
(Korea)
(Taiwan)
(General)
VPC-S6GX
(Product Code : 168 028 03)
(Southeast Asia)
(Middle East)
(Hong Kong)
REFERENCE No. SM5310630
Advertisement
Table of Contents
Related Manuals for Sanyo VPC-S6U
Summary of Contents for Sanyo VPC-S6U
-
Page 1: Table Of Contents
FILE NO. SERVICE MANUAL Digital Camera VPC-S6U (Product Code : 168 028 01) (U.S.A.) (Canada) VPC-S6 (Product Code : 168 028 02) (Europe) (South America) (China) (Australia) (Korea) (Taiwan) (General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ....3 VPC-S6GX 2. DISASSEMBLY ............11 3. - Page 2 WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sure to use lead-free solder when carrying tured up until now, remove all of the existing solder at those out repair work, and never use solder containing lead.
-
Page 3: Outline Of Circuit Description
1. OUTLINE OF CIRCUIT DESCRIPTION Pin 1 1-1. CCD CIRCUIT DESCRIPTION 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. IC903 (MN39830PMJAA) CCD imager IC901 (AN20112A) V driver IC905 (AD9948AKCP) CDS, AGC, A/D converter, H driver Pin 13 2. - Page 4 3. Part of IC905 (H Driver) and IC901 (V Driver) 4. IC905 (H Driver, CDS, AGC and A/D converter) An H driver (part of IC905) and V driver (IC901) are neces- IC905 contains the functions of H driver, CDS, AGC and A/D sary in order to generate the clocks (vertical transfer clock, converter.
- Page 5 1-2. CP1 CIRCUIT DESCRIPTION 2. Outline of Operation 1. Circuit Description When the shutter opens, the reset signals and the serial sig- 1-1. Digital clamp nals (“take a picture” commands) from the 8-bit microproces- The optical black section of the CCD extracts averaged val- sor are input to ASIC (IC101) and operation starts.
- Page 6 1-3. PWA POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog System Power Output This is the main power circuit, and is comprised of the follow- +12 V (A), +3.45 V (A) and -6.0 V (A) are output. Feedback for ing blocks. the +12 V (A) is provided to the switching controller (Pin (4) of Switching controller (IC501) IC501) so that PWM control can be carried out.
- Page 7 1-4. STA STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When FLCLT signals are input from the ASIC expansion port, CHG signal from microprocessor becomes High (3.3 V), the the stroboscope emits light.
- Page 8 1-5. SYA CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SYA block, refer to the block diagram. The SYA block centers around a 8-bit microprocessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions. 1.
- Page 9 XCIN Clock oscillation terminal for clock (32.768 kHz) FLMDO Microprocessor Port Main clock oscillation terminal (not used) XOUT Main clock oscillation terminal (not used) VREF Standard voltage Table 5-1. 8-bit Microprocessor Port Specification 2. Internal Communication Bus The SYA block carries out overall control of camera operation by detecting the input from the keyboard and the condition of the camera circuits.
- Page 10 4. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off. When the battery is attached, IC955 is operating and creating 3.6 V, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, clock counting and key scanning is carried out even when the power switch is turned off, so that the camera can start up again.
-
Page 11: Disassembly
2. DISASSEMBLY 2-1. REMOVAL OF CABI BACK 1. Two screws 1.7 x 6 11. Screw 1.7 x 4 2. Open the cover battery. 12. Screw 1.7 x 3 3. Screw 1.7 x 4 13. Screw 1.7 x 2 4. Cabinet bottom 14. - Page 12 2-2. REMOVAL OF LCD 1. Spacer under monitor 2. LCD 3. Remove the solder. 4. FPC 5. Two screws 1.4 x 3.5 6. Two screws 1.7 x 4 7. FPC 8. Holder monitor 9. Screw 1.7 x 2 10. Spring earth CP1 11.
- Page 13 2-3. REMOVAL OF CP1 BOARD AND LENS ASSEMBLY 1. Remove the solder. 9. CP1 board 17. Two screws 1.7 x 3 2. Buzzer 10. Remove the solder. 18. Holder strap 3. Remove the solder. 11. Condensor 19. Dec self LED 4.
- Page 14 2-4. REMOVAL OF CABI FRONT AND TB1 BOARD 1. Three screws 1.7 x 3 2. Cabinet top 3. Cabi front 4. Spacer flash 5. Screw 1.7 x 2.5 6. Shield tape TB1 7. Screw 1.7 x 2.5 8. TB1 board 9.
- Page 15 2-5. BOARD LOCATION TB1 board CP1 board – 15 –...
-
Page 16: Electrical Adjustment
3. ELECTRICAL ADJUSTMENT 6. LCD Panel Adjustment 3-1. Table for Servicing Tools 6-1. LCD VcomPP Adjustment Part code 6-2. LCD VcomDC Adjustment Ref. No. Name Number Note: Item 2-5 adjustments should be carried out in sequence. Pattern box (color viewer) VJ8-0190 VJ8-0263 Calibration software... - Page 17 3-6. The adjustment item which in necessary in part exchange CCD Black CCD White IC501 Point And Lens Point Factory Oscillation White Point Language storage Reset VcomPP VcomDC Adjust- Adjust- Defect Cord Frequency Defect Detect Setting information Setting Adjust- Adjust- Detect Setting ment...
- Page 18 Preparation: DscCalDi POWER switch: ON Adjusting method: Focus Result 1. When setting the camera in place, set it to an angle so that ZOOM_BACKRUSH: 17 nothing appears in any part of the color viewer except the AF_WIDE: 24 white section. (Do not enter any light.) AF_MID1: 20 2.
- Page 19 5. CCD Black Point And White Point Defect Detect 6-1. LCD VcomPP Adjustment Adjustment In Lighted Preparation: POWER switch: ON Adjusting method: 1. Double-click on the DscCalDi.exe. 2. Select “0” in the LCD “VCOMPP”. 3. Adjust LCD “VCOMPP” so that the amplitude of the CL404 waveform is 5.60 V ±...
- Page 20 3-9. Language Setting 5. Choose the OPTION icon. 1. Click on the " " mark located on the right of the 6. Choose the FORMAT. "Language" display BOX. 7. Press the left arrow button for 2 seconds. FIRMWARE UP- 2. Select language. (Default is English.) DATE will display.
-
Page 21: Usb Storage Information Registration
16.) 2. Double-click on the DscCalDi.exe. 3. Click on the Get button in the USB storage window and check the USB storage data. VID: SANYO PID: S6 Serial: Rev. : 1.00 4. -
Page 22: Troubleshooting Guide
5. TROUBLESHOOTING GUIDE POWER LOSS INOPERTIVE TAKING INOPERATIVE PUSH RELEASE PUSH THE POWER SWITCH SB LED IS FLASHING STROBE CHARGE IC301-15 CHECK SYA BLOCK WHEN AUTO INOPERATIVE (SCAN IN 0) LUMINOUS (RED) CHECK STA BLOCK PULSE INPUT CN301-5, 6 CHECK CHECK IC302-7 (SCAN IN 1, 2) - Page 23 MEMO...
-
Page 24: Parts List
6. PARTS LIST ELECTRICAL PARTS Note: 1. Materials of Capacitors and Resistors are abbreviated as follows ; Resistors Capacitors MT-FILM Metallized Film Resistor MT-POLYEST Metallized Polyester Capacitor MT-GLAZE Metallized Glaze Resistor MT-COMPO Metallized Composite Capacitor OXIDE-MT Oxide Metallized Film Resistor TA-SOLID Tantalum Solid Capacitor AL-SOLID... - Page 25 LOCATION PARTS NO. LOCATION PARTS NO. DESCRIPTION DESCRIPTION LOCATION PARTS NO. LOCATION PARTS NO. DESCRIPTION DESCRIPTION L1002 645 059 8111 IMPEDANCE,1000 OHM P (N.S.P) C3012 403 276 1007 CERAMIC 0.01U K 16V (N.S.P) L1003 645 020 1912 INDUCTOR,240 OHM (N.S.P) C3013 403 276 1304 CERAMIC...
- Page 26 LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION C9502 403 338 0306 CERAMIC 0.1U K 10V (N.S.P) R3006 401 258 7009 MT-GLAZE 150K DC 1/16W (N.S.P) C9503 403 383 5202 CERAMIC 4.7U K 6.3V (N.S.P) R3007 401 258 7009 MT-GLAZE 150K DC 1/16W (N.S.P) C9504 403 338 0306...
-
Page 27: Accessories & Packing Materials
MT-GLAZE 0.000 ZA 1/16W (N.S.P) ACCESSORIES & PACKING MATERIALS R9023 401 237 2506 MT-GLAZE 4.7 JA 1/16W (N.S.P) 645 079 1369 CABLE,DSC USB,EXCEPT VPC-S6U R9032 401 226 1503 MT-GLAZE 0.000 ZA 1/16W (N.S.P) 645 078 0943 CABLE,DSC USB-PRINTED,VPC-S6U ONLY R9033 401 226 1503 MT-GLAZE 0.000 ZA 1/16W... -
Page 28: Cabinet & Chassis Parts 1
LOCATION PARTS NO. DESCRIPTION CABINET & CHASSIS PARTS 1 636 089 7564 CABINET FRONT-SX813/J,EXCEPT VPC-S6U 636 092 8497 CABINET FRONT-SX813/U,VPC-S6U ONLY 636 091 7200 ADHESIVE DEC SELF-SX813/J 636 090 1575 COVER DEC SELF-SX813/J 636 092 8923 ADHESIVE DEC FLASH-813/J 636 089 7625... - Page 29 Cabinet 1 12 (N.S.P.) Ver.1 SX813/J 2005.08...
-
Page 30: Cabinet & Chassis Parts 2
LOCATION PARTS NO. DESCRIPTION CABINET & CHASSIS PARTS 2 636 089 7724 HOLDER CHASSIS-SX813/J 420 002 1407 PZ BZR HADU21290161 645 079 8030 ASSY,LAMP-SX813 636 092 6769 LABEL CAUTION BATT B 813J 636 092 6783 LABEL CAUTION BATT A 813J 636 089 7892 TERMINAL BATT A-SX813/J 636 089 7687... - Page 31 Cabinet 2 29 102 C5412 Ver.1 SX813/J 2005.08...
- Page 32 SANYO Electric Co., Ltd. Osaka, Japan Printed in Japan Sep./’05...