Manual Channel Set - JVC DR-MV1B Instructions Manual

Filename [DR-MV1SEK_10Subsidiary.fm]
DR-MV1SEK_10Subsidiary.fm Page 84 Thursday, April 22, 2004 5:13 PM
SUBSIDIARY SETTINGS
84
EN
4
View the Confirmation screen. "SCAN COMPLETED" is
displayed on the TV screen. Press "OK".
5
Press SET UP to complete the setting.
When Auto Channel Set is completed, "PLEASE WAIT" will be
displayed for about 90 seconds, since channel data is exchanged
between the DVD deck and the VHS deck. No operations will be done
during this time.
Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations. Refer to
pages 84 – 85 for the procedures.
Depending on reception conditions, the stations may not be stored in
order, and the station names may not be stored correctly.
IMPORTANT:
In certain reception conditions, station names may not be stored
correctly, and Auto Guide Program Number Set may not work
properly. When the Guide Programme numbers are not set
properly, the programme that you do not intended to record will be
timer-recorded by the VIDEO Plus+ system of the unit. When
programming the timer using the VIDEO Plus+ system, be sure to
check the desired channel is selected correctly. (
Your unit memorises all receivable stations even if reception of
some of them is poor. You can delete those stations with an
unacceptable picture from the list. (
NOTES:
Fine tuning is performed automatically during Auto Channel Set. If
you want to perform tuning manually, refer to "Fine-Tuning Channels
Already Stored" ( pg. 85).
If you perform Auto Channel Set when the aerial cable is not
connected properly, "SCAN COMPLETED –NO SIGNAL–" appears
on the TV screen in step 4. In such a case, make sure of the aerial
connection and press ENTER; Auto Channel Set will start again.
Page 84
pg. 45, 56)
pg. 85, "Delete A Channel")
Masterpage:Left+

Manual Channel Set

Store channels that were not stored during Auto Set Up
( pg. 19), Preset Download (
( pg. 83).
VCR/DVD
1
4
7
ENTER
SET UP
1
Press SET UP to access the Main Menu screen.
2
Press w e to select "INITIAL SET UP", then press ENTER.
3
Press w e to select "MANUAL CH SET", then press ENTER.
The Confirmation screen appears.
4
Press rt w e to select a
blank position in which you want to
store a channel, then press
ENTER twice. The Manual
Channel Set screen appears.
5
Press rt to select "BAND",
then press ENTER.
6
Press rt to change the band
between CH (regular) and CC
(cable), then press ENTER.
7
Press rt to select "CH", then
press ENTER.
8
Press rt to input the channel
number you want to store.
To enter the registered station
name ( pg. 100), press rt to
select "ID", then press ENTER. Press rt.
For fine tuning adjustment, press rt to select "FINE", then press
ENTER. Press rt to perform fine-tuning.
When "L-2 SELECT" is set to "VIDEO", "S-VIDEO", "SAT VIDEO" or
"SAT S-VIDEO", the "DECODER" setting cannot be changed.
( pg. 74)
9
Press ENTER to enter new channel information. The
Confirmation screen appears.
Repeat steps 4 – 9 as necessary.
10
Press SET UP to close the Confirmation screen.
When Auto Channel Set is completed, "PLEASE WAIT" will be
displayed for about 90 seconds, since channel data is exchanged
between the DVD deck and the VHS deck. No operations will be done
during this time.
To change positions, see "Change Station Channel Position"
( pg. 85).
If you wish to set station names other than the ones registered in your
unit, see "Set Stations (B)" ( pg. 85).
ATTENTION:
Guide Program numbers are not set when channels are stored
manually. ( pg. 83, "VIDEO Plus+
pg. 20) or Auto Channel Set
SAT
2 3
5 6
8 9
0
rtw e
(Example) To store in position 6.
The programme currently
received on the selected channel
position appears behind the
confirmation screen.
® System Setup")
April 22, 2004 5:12 pm