Manual Timer Programming - JVC DR-MV1B Instructions Manual

Filename [DR-MV1SEK_06DVD Operation2.fm]
DR-MV1SEK_00.book Page 46 Thursday, April 15, 2004 3:30 PM
OPERATIONS ON DVD DECK
46
EN

Manual Timer Programming

You can programme this unit to timer-record as many as
8 programmes.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
DVD TIMER (#)
VCR/DVD
1
4
7
PROG/CHECK
ENTER
1
Load a recordable disc.
2
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3
Press PROG/CHECK to
access the Programme Check
screen.
When "PROGRAMME FULL
DELETE UNWANTED TIMER
PROGRAMME" appears on the
TV screen, you need to cancel
some of the reserved
programmes. ( pg. 49)
4
Press rt to select "NEW
TIMER PROGRAMME", then
press ENTER. The programme
screen appears.
5
Press rt to set the desired
date.
The current date appears on the
TV screen. The date you enter
appears in its place.
6
Press w e to select "START", then press rt to set the desired
start time.
Each press of rt advances/goes back the start time in 1-min.
increments.
To advance/go back the start time in 30-min. increments, press and
hold rt.
7
Press w e to select "STOP", then press rt to set the desired
stop time.
Each press of rt advances/goes back the stop time in 1-min.
increments.
To advance/go back the stop time in 30-min. increments, press and
hold rt.
8
Press w e to select "TV PROG", then press rt to select the
desired channel.
9
Set the other recording options as required.
Refer to step 6 in "VIDEO Plus+
Page 46
SAT
2 3
5 6
8 9
AUX
0
DISPLAY
rtw e
® Timer Programming" ( pg. 45).
10
Press ENTER to access the Programme Confirmation screen.
11
Press ENTER to complete timer programming.
To programme another timer, repeat steps 3 – 11.
12
Press DVD TIMER (#) to engage the unit's timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. Press 1 to turn off the unit. When the
VCR deck is in timer standby mode, the unit is automatically turned
off.
To disengage the timer mode, press DVD TIMER (#) again.
NOTES:
When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform "Satellite Receiver Control Setting (DVD Deck Only)"
( pg. 23).
B Perform "Manual Timer Programming" (
press AUX to change "TV PROG" to "SAT". Then press rt to
enter the channel position for the satellite broadcast. In step 9,
you cannot set "VPS/PDC" to "ON".
C Leave the satellite receiver's power on.
PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) is a service designed to assure safe, accurate timer
recording. With this system, special code signals are transmitted
together with the audio/video signals. These code signals control
your unit and have precedence over the advertised times which
you may have preset into the timer. This means that your unit will
start and stop recording when the preset TV programmes actually
start and end — even if the broadcast time of a preset TV
programme is changed from what has been advertised. PDC is
currently available nationally on BBC1, BBC2, Ch.4 and Ch.5,
except from a few small relay transmitters. Ch.3 operates a PDC
service in some areas. All channels intend to offer this service in
due course. Check your TV programme listing guide for latest
information. If the channel you intend to record does not offer a
PDC service your unit will not start recording if PDC has been
selected. Be sure to set PDC to "OFF" if PDC is not available on
your selected channel. (See step 6 on page 45.)
NOTES:
When you use Manual Timer Programming, set the start time (PDC
time) exactly as advertised in the TV listing. A different time than
advertised will result in no recording.
PDC recording is also possible when a satellite receiver or a cable
system is connected to L-2 IN/DECODER connector on your unit.
PDC recording is also possible via the L-1 IN/OUT connector.
Masterpage:Left+
pg. 46). In step 8,
April 15, 2004 3:30 pm